FREESTANDING COOKER OR90 Dual Fuel models INSTALLATION GUIDE GB IE
SAFETY AND WARNINGS ! WARNING! z Electric Shock Hazard Failure to follow this advice may result in electric shock or death. • Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. • Connection to a good earth wiring system is absolutely essential and mandatory. z • Alterations to the domestic wiring system must only be made by a qualified electrician. ! WARNING! z Cut Hazard Failure to use caution could result in injury.
GENERAL INSTALLATION INFORMATION Cleaning and servicing z z z z z z z z z Service should only be performed by an authorised technician. When removing appliance for cleaning and/or service: Shut off gas at main supply. Disconnect AC power supply. Disconnect gas line to the inlet pipe. Carefully remove the cooker by pulling outward. CAUTION: Cooker is heavy; use care in handling. The misuse of oven door (eg stepping, sitting, or leaning on them) can result in potential hazards and/or injuries.
PARTS SUPPLIED FOR INSTALLATION Anti-tip bracket (1) Screws and plastic sleeve anchors (2) 1/2" cylindrical connector and fibre washer (1) TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE) IMPORTANT! THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier.
MODEL IDENTIFICATION Model features may vary. OR90 models OR90SCG4 OR90SDG4 OR90SCG6 OR90SDG6 PRIOR TO INSTALLATION Unpacking and handling z z z Inspect the cooker to verify that there is no shipping damage. If any damage is detected, call the shipper and initiate a damage claim. Fisher & Paykel is not responsible for shipping damage. DO NOT discard any packing material until the cooker has been inspected. Remove the outer carton and any packing material from cooker.
PRODUCT DIMENSIONS Model features may vary. Optional kickstrip is available (purchased separately). C D E A F G FRONT PROFILE B OR90 DUAL FUEL PRODUCT DIMENSIONS mm C PLAN 6 A Overall height of cooker (from floor to top of cooktop, excluding grates and optional backguard) B Overall width of cooker 897 C Overall depth of cooker (from front of cooker to rear of backguard, excluding handles and dials) 600 D Height of optional backguard from top of cooktop 60 E Height of chassis (excl.
CLEARANCE DIMENSIONS OR90 DUAL FUEL CLEARANCE DIMENSIONS MM A Minimum vertical distance between benchtop and cabinet extending above counter B Minimum clearance from left and right edge of cooker to nearest vertical combustible surface 450 C 200 C Minimum clearance from cooking surface to: z Overhead cabinet centered above the cooktop z Ventilation hood centered above the cooking surface 650 650 D Width of cabinetry opening 900 E Maximum height of cabinetry immediately adjacent to the cooker (from fl
FITTING THE OPTIONAL BACKGUARD LOCATION OF ELECTRICAL SUPPLY Backguard z z z Remove the screws and spacers on the rear of the cooktop. Assemble the backguard as shown and fix onto the back of the cooker using the same screws and spacers. Fix the backguard onto the cooker using the screws provided.
VENTILATION REQUIREMENTS A suitable ventilation hood may be installed above the cooker. Fisher & Paykel has a choice of ventilation hoods designed to match the rest of our kitchen appliance family. See fisherpaykel.com or your local dealer for more details. Hood (inc. combustible) 650mm Wall Installation Hood (inc.
FITTING THE ADJUSTABLE FEET Fitting the adjustable feet Fitting the adjustable feet covers (optional) The adjustable feet must be fitted to the base of the cooker before use. If using the adjustable feet covers fit these while the cooker is tipped over. Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the fitting of the feet. IMPORTANT Take care not to damage the cooker during this operation.
MOVING THE COOKER IMPORTANT! z z z When raising cooker to upright position always ensure two people carry out this manoeuvre to prevent damage to the adjustable feet. Be careful: do not lift the cooker by the oven door handle, the hob rail or by lifting the cooktop trim as this may damage the appliance. When moving cooker to its final position DO NOT DRAG. Lift feet clear of floor.
INSTALLING THE ANTI-TIP BRACKET IMPORTANT! z z z To restrain the cooker and prevent it tipping accidentally secure the cooker to the wall using the supplied anti-tip bracket. If installing the cooker above a plinth (without fitting the adjustable feet) revise the installation dimensions for the anti-tip bracket accordingly, considering that the feet have the following measurements: min 85mm – max 133mm.
ELECTRICAL CONNECTION IMPORTANT! z This cooker must be connected to the mains power supply only by a suitably qualified person in accordance with current regulations. This cooker must be earthed. z The appliance must be connected to the mains checking that the voltage corresponds to the value given in the rating plate and that the electrical cable sections can withstand the load specified on the plate.
CONNECTION OF THE POWER SUPPLY CABLE IMPORTANT! The power supply cable must be connected by an authorised service person. DO NOT unscrew the screws fixing the cover plate behind the terminal block. z z Feeder cable section Use type HO5RR-F cable. MODEL CABLE SPECIFICATIONS OR90S models 220 – 240 V 50Hz 3 x 2,5 mm2* *Connection with wall box connection. OR90SG6 MODELS ONLY 1 2 L cable clamp 1 Unhook the terminal board cover by inserting a screwdriver into the two hooks at the base of the block.
GAS CONNECTION Gas supply z z z The connection must be performed by an authorised person according to the relevant standards. This appliance is suitable for use with Natural Gas or LPG. The gas cooker is shipped from the factory set and adjusted for Natural Gas. It can be converted for use with LPG following the instructions in this manual. If the Natural gas/LPG conversion kit is not supplied with the appliance this kit can be purchased by contacting the After-Sales Service.
GAS CONNECTION IMPORTANT! z z The connection must be performed by an authorised person according to the relevant standards. The gas supply must use the gas inlet pipe which is located at the left hand side at the rear of the appliance. gas inlet pipe 20mm 10mm 10mm 20mm connector IMPORTANT! Use two wrenches to tighten the connection. 1 Before connecting the appliance to the gas main, fit the female connector to the left inlet pipe using the fibre washer supplied.
FLAME TESTING z z z z The operation of the appliance must be tested when installation is completed. Turn on the appliance gas controls and light each burner individually and in combination. Check for a well defined blue flame without any yellow tipping. If any abnormality is evident then check that the burner cap is located properly and the injector nipple is aligned correctly. Check the minimum burner setting by quickly rotating the gas control knob from the maximum to the minimum position.
GAS CONVERSION Conversion to LP/Propane Gas Replacing the cooktop burner injectors Conversion to LPG 1 Remove the pan supports, the burner caps and the flame spreaders. 2 Using a wrench substitute the nozzle injectors with those most suitable for the kind of gas for which it is to be used. 3 Adjust the minimum burner setting (see ‘Adjusting the minimum burner setting’) 4 Refit the flame spreaders, the burner caps and the pan supports.
ADJUSTING THE MINIMUM BURNER SETTINGS Adjusting the cooktop burner minimums Check whether the flame spreads to all burner ports when the burner is lit with the gas tap set to the minimum position. z z z If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit even when the gas tap is turned quickly from the maximum to the minimum position. If the burner does not remain lit, increase the minimum gas rate setting.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL OPERATION F Placement of unit. F All internal packing materials removed. Check below the cooktop grates and inside the oven. F Specified clearance maintained to cabinet surfaces. F If converted for use with ULPG, confirm that the test point adapter and cooktop F Unit Level — front to back, side to side. burner injectors have been correctly set for use with ULPG. F All packaging material and tie straps removed.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. GB IE 591554C 06.
