COMPANION PRODUCTS Warming Drawer WB24 Coffee Maker EB24 Steam Oven OS24N Speed Oven OM24N models INSTALLATION GUIDE US CA 591496F 08.
CONTENTS Warming drawer 1 Coffee maker 12 Speed oven 29 1 Safety and warnings 2 1 Safety and warnings 13 1 Safety and warnings 30 2 Parts supplied 3 2 Parts supplied 14 2 Prior to installation 31 3 Prior to installation 3 3 Prior to installation 14 3 After installation 31 4 Product dimensions 4 4 After installation 14 4 Product dimensions 32 5 Product dimensions 15 5A Cabinetry dimensions (18 1/8" (460mm) high cavity) 33 5B Cabinetry dimensions (18 7/8" (480mm)
WARMING DRAWER WB24 models
1 SAFETY AND WARNINGS WARNING! Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good earth wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death.
2 Screws (4) Anti-tip bracket (1) Oven support brackets (2) 3 ● ● ● ● ● ● The The The The The You PARTS SUPPLIED PRIOR TO INSTALLATION cavity is square and level, and of the required dimensions. installation will comply with all clearance requirements and applicable standards and regulations. power switch will be easily accessible to the customer when the warming drawer is installed. warming drawer (and any product on top of it) will rest on a surface that can support its weight.
4 PRODUCT DIMENSIONS D B C I A F FRONT G SIDE E Terminal Block D PRODUCT DIMENSIONS C J A Overall height of product B Overall width of product C Depth of drawer front panel (excluding handle)* K D Depth of chassis (including terminal block) E Width of chassis at rear PLAN H F Height from bottom drawer panel to bottom of chassis at rear G Height from bottom of drawer panel to top of chassis H Depth of drawer (open) (measured from front of drawer) I Height of drawer front panel J Depth
D J H F I A THE FOLLOWING PAGES DETAIL COMMON CABINETRY SCENARIOS L 5A G CABINETRY DIMENSIONS – UNDERBENCH (ieEINSTALLED WITH F&P SINGLE OVEN) N ** C O Oven 28 3/8" (720mm) Oven M Oven support brackets G K B Warming drawer *PO PLAN Warming drawer Fit the supplied oven support brackets Tab SIDE Unscrew-fitrescrew Oven support bracket CABINETRY DIMENSIONS inches (mm) M Minimum inside height of cavity 27" (687) N Inside width of cavity 22" (560) O Minimum inside depth of cavity
5B CABINETRY DIMENSIONS – WALL MOUNTED (ie INSTALLED WITH A F&P COMPACT OVEN) N Compact oven O M 23 5/8" (600mm) Warming drawer Compact oven *PO PLAN SIDE Warming drawer Compact oven Lower trim kit (optional, supplied separately) M Warming drawer Additional 11/16" (18mm) Wood Spacer Cabinet below CABINETRY DIMENSIONS M Minimum inside height of cavity with optional Lower trim kit fitted without optional Lower trim kit fitted inches (mm) 23 1/4" (590) 22 1/2" (570) N Inside width of cavity O
5C CABINETRY DIMENSIONS – WALL MOUNTED (ie INSTALLED WITH A F&P COFFEE MAKER) IMPORTANT! If installing under the F&P Coffee Maker, ensure there is the 2" (50mm) gap at the back of the cabinet and the 7 7/8"2 (200mm2) toekick cutout required for airflow. Refer to the Coffee Maker Install instructions.
5D CABINETRY DIMENSIONS – WALL MOUNTED (STANDALONE) Supplied anti-tip bracket (screwed to the back wall) IMPORTANT! In a standalone wall mounted installation, you must ensure that the supplied anti-tip bracket is installed unless there is a fixed shelf above acting as an anti-tip obstacle.
6 DISCARD PACKAGING RESPONSIBLY Unpack the warming drawer and inspect for any signs of damage. Do not install the warming drawer if it has been damaged. IMPORTANT! Packing materials (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as they may cause serious injuries.
9 SECURE THE WARMING DRAWER TO THE CABINETRY 1 Ensure the warming drawer is level and positioned in place in the cavity. IMPORTANT! Do not lift the warming drawer by the drawer handle. 2 Fully open the drawer. 3 Fasten the warming drawer in place with the two screws supplied, through the front trim, beneath the drawer. Do not overtighten the screws.
!1 FP WARMER DRAWER INTERFACE LOGIC_V1 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER F Make sure the warming drawer is level and securely fitted to the cabinetry. P WARMER DRAWER INTERFACE LOGIC_V1 FP WARMER DRAWER INTERFACE LOGIC_V1 F Make sure any internal packaging has been removed from the drawer. PRODUCT OFF F Make sure that the isolating switch is accessible by the customer. 1h Make sure the anti-tip bracket has been fitted correctly if it is required.
COFFEE MAKER EB24 models 560.00 12.95 00.00 20.
1 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS! ● Installation ● WARNING! ● ● Cut Hazard Take care – some edges are sharp. Failure to use caution could result in injury or cuts. ● ● ● Checking for transport damage After removing the packaging, make sure the product is complete and undamaged and that all accessories are present. Do not use the appliance if it is visibly damaged. Contact Customer Care.
2 Screws (28) PARTS SUPPLIED Clip (1) Rails (2) Spacers (4) for side (4) for bottom 3 ● ● ● ● ● ● ● ● ● PRIOR TO INSTALLATION The countertop and coffee maker cavity are square and level, and are the required dimensions. 560.00 The installation will comply with all clearance requirements and applicable standards and regulations. The isolating switch will be easily accessible to the customer with the coffee maker installed. 352.
5 PRODUCT DIMENSIONS E H C F D SIDE TOP B I PRODUCT DIMENSIONS A Overall height of product A B Overall width of product C FRONT Overall depth of product (excluding dials) EB24 MODELS inches (mm) 18" (458) 23 1/2" (596) 18 7/8" (480) D Height of chassis 17 1/2" (445) E Width of chassis 22 1/16" (560) F Depth of chassis 18 1/8" (460) G Depth of coffee maker frame and control panel H Stepdown control panel to chassis I Height of control panel 13/16" (20) 1/2" (13) 4" (100) COFFEE MAKER
6A CABINETRY DIMENSIONS (18 1/8" (460mm) HIGH CAVITY) Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be installed in a column and the column must be firmly fixed to the wall with commercially available brackets. IMPORTANT! PROUD INSTALL All installation or maintenance operations must be performed with the appliance disconnected from the mains electricity supply.
6B CABINETRY DIMENSIONS (18 7/8" (480mm) CAVITY TRIM KIT) Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be installed in a column and the column must be firmly fixed to the wall with commercially available brackets. Lower Trim Kit The Lower Trim kit shown is available to order separately from fisherpaykel.com. To install the trim kit, refer to the instructions which accompany it.
7 INSTALLATION INSTRUCTIONS " 0.07 ) m (1.8m approx. 13 3/4" (350mm) 1 Position the rails on the sides of the cabinet. Fix with the screws provided, then extract them completely. ● If the coffee maker is installed over a warmer drawer, use the top surface of this as a reference to position the rails. ● In this case, there will be no surface to rest the rails on. 2 Fix the power cable with the clip.
8 CONNECT THE WARMING DRAWER TO THE MAINS SUPPLY IMPORTANT! ● ● All electrical work may only be carried out by suitably qualified and competent persons in accordance with national and local safety regulations. This warming drawer must be grounded. Before placing the coffee maker into the cavity, route the power cord into the back of the cavity and plug it in to the switched socket. The switched socket should be in an easily accessible area within 35 7/16" (900mm) of the centre rear of the product.
9 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER F Make sure the coffee maker is level and securely fitted to the cabinetry. F Check the lower trim is undamaged. F Check there is adequate clearance. This is to ensure correct air circulation. F Make sure any cable ties and internal packaging has been removed from the coffee maker cavity. F Make sure all coffee maker vents and openings are clear and free of any obstruction or damage.
STEAM OVEN OS24N models 42.00 556.00 565.30 5 22.
1 SAFETY AND WARNINGS Installation ● WARNING! Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good ground wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician Failure to follow this advice may result in electrical shock or death.
2 ● ● ● ● ● ● ● ● ● PRIOR TO INSTALLATION The countertop and oven cavity are square and level, and are the required dimensions. 560.00 The installation will comply with all clearance requirements and applicable standards and regulations. The isolating switch will be easily accessible to the customer with the oven installed. 352.00 The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 59 1/16" (1.
4 PRODUCT DIMENSIONS E C F D G TOP SIDE H B PRODUCT DIMENSIONS A Overall height of product A B Overall width of product C FRONT Overall depth of product (excluding handle and dials) STEAM OVEN INSTALLATION GUIDE 18" (458) 23 7/16" (596) 22 1/8" (562) 17 1/2" (445) E Width of chassis 21 7/8" (556) F Depth of chassis 21 1/4" (540) G Depth of oven frame and control panel 7/8" (22) (=distance between front of chassis and front of oven door, excl.
5A CABINETRY DIMENSIONS (18 1/8" (460mm) HIGH CAVITY) The oven can be installed under a cooktop, in a column, or combined with the companion warmer drawer. The cabinet material must be able to withstand heat. The oven must be centered within the walls of the cabinet and fixed with the screws and bushings that are provided.
5B ● ● ● CABINETRY DIMENSIONS (18 7/8" (480mm) CAVITY TRIM KIT) The oven must be installed under a cook top, in a column, or combined with the companion warmer drawer. The cabinet material must be able to withstand heat. The oven must be centred within the walls of the cabinet and fixed with the screws and bushings that are provided. Lower Trim Kit The Lower Trim kit shown is available to order separately from fisherpaykel.com. To install the trim kit, refer to the instructions which accompany it.
6 ● ● ELECTRICAL HOOK-UP Before connecting to the electricity, make sure that the: specifications of the electrical system match with what is detailed on this section. (Fig. 1) system has an effective ground connection compliant with current standards and laws. The ground connection is required by law. The cable must not, at any point, reach a temperature greater than 122°F (50°C) above room temperature.
8 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER F Make sure the oven is level and securely fitted to the cabinetry. F Check the lower trim is undamaged. F Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction.
SPEED OVEN OM24N models 42.00 556.00 565.30 35 22.
1 SAFETY AND WARNINGS Installation ● WARNING! Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good ground wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician Failure to follow this advice may result in electrical shock or death.
2 ● ● ● ● ● ● ● ● ● PRIOR TO INSTALLATION The countertop and oven cavity are square and level, and are the required dimensions. 560.00 The installation will comply with all clearance requirements and applicable standards and regulations. The isolating switch will be easily accessible to the customer with the oven installed. 352.00 The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 59 1/16" (1.
4 PRODUCT DIMENSIONS E C F D G TOP SIDE H B PRODUCT DIMENSIONS A Overall height of product A B Overall width of product C FRONT Overall depth of product (excluding handle and dials) SPEED OVEN INSTALLATION GUIDE 18" (458) 23 7/16" (596) 22 1/8" (562) 17 1/2" (445) E Width of chassis 21 7/8" (556) F Depth of chassis 21 1/4" (540) G Depth of oven frame and control panel 7/8" (22) (=distance between front of chassis and front of oven door, excl.
5A CABINETRY DIMENSIONS (18 1/8" (460mm) HIGH CAVITY) The oven can be installed under a cooktop, in a column, or combined with the companion warmer drawer. The cabinet material must be able to withstand heat. The oven must be centered within the walls of the cabinet and fixed with the screws and bushings that are provided.
5B ● ● ● CABINETRY DIMENSIONS (18 7/8" (480mm) CAVITY TRIM KIT) The oven must be installed under a cook top, in a column, or combined with the companion warmer drawer. The cabinet material must be able to withstand heat. The oven must be centred within the walls of the cabinet and fixed with the screws and bushings that are provided. Lower Trim Kit The Lower Trim kit shown is available to order separately from fisherpaykel.com. To install the trim kit, refer to the instructions which accompany it.
6 ● ● ELECTRICAL HOOK-UP Before connecting to the electricity, make sure that the: specifications of the electrical system match with what is detailed on this section. (Fig. 1) system has an effective ground connection compliant with current standards and laws. The ground connection is required by law. The cable must not, at any point, reach a temperature greater than 122°F (50°C) above room temperature.
8 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER F Make sure the oven is level and securely fitted to the cabinetry. F Check the lower trim is undamaged. F Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction.
PRODUITS COMPAGNONS Modèles Tiroir chauffant WB24 Machine à café EB24 Four à vapeur OS24N Four à micro-ondes OM24N GUIDE D’INSTALLATION US CA 591496F 08.
TABLE DES MATIÈRES Tiroir chauffant 1 Machine à café 12 Four à micro-ondes 28 1 Sécurité et avertissements 2 1 Sécurité et avertissements 13 1 Sécurité et avertissements 29 2 Pièces fournies 3 2 Pièces fournies 14 2 Avant l’installation 30 3 Avant l’installation 3 3 Avant l’installation 14 3 Après l’installation 30 4 Dimensions du produit 4 4 Après l’installation 14 4 Dimensions du Produit 5 Dimensions du produit 15 5A Dimensions de l’armoire (cavité de 18 1/8" (4
TIROIR CHAUFFANT Modèles WB24
1 SÉCURITÉ ET AVERTISSEMENTS AVERTISSEMENT! Danger de choc électrique Avant d’effectuer tout travail sur la partie électrique de l’appareil, celui-ci doit être déconnecté du secteur. La connexion à un bon système de mise à la terre est absolument essentielle et obligatoire. Les modifications apportées au système de câblage domestique ne doivent être effectuées que par un électricien qualifié. Le non-respect de ce conseil peut entraîner un choc électrique ou la mort.
2 Des vis (4) Support anti-basculement (1) Supports de support de four (2) 3 ● ● ● ● ● ● PIÈCES FOURNIES AVANT L’INSTALLATION La cavité est carrée et de niveau, et des dimensions requises. L’installation sera conforme à toutes les exigences de dégagement et aux normes et règlements applicables. L’interrupteur d’alimentation sera facilement accessible au client lorsque le tiroir-réchaud est installé.
4 DIMENSIONS DU PRODUIT D B C I A F AVANT G LE CÔTÉ E Bornier D DIMENSIONS DU PRODUIT C J 4 5/8" (118) 4 5/8" (118) 23 1/2" (596) 13/16" (20) 7/8" (22) D Profondeur du châssis (y compris le bornier) 21 1/8" (536) 21 1/8" (536) E Largeur du châssis à l’arrière 21 3/4" (551) 21 3/4" (551) G Hauteur entre le bas du panneau du tiroir et le haut du châssis H Profondeur du tiroir (ouverte) (mesurée depuis l’avant du tiroir) I Hauteur du panneau avant du tiroir J Profondeur de la poignée
D J H F I A LES PAGES SUIVANTES DÉTAIL SCÉNARIOS D’ARMOIRES COMMUNES L 5A G E INSTALLÉ AVEC F&P FOUR UNIQUE) DIMENSIONS DE L’ARMOIRE – UNDERBENCH (ie N ** C O Four 28 3/8" (720mm) Four M Supports de support de four G K B Tiroir chauffant *PO HAUT Tiroir chauffant Monter les supports de four fournis Attache LE CÔTÉ CABINETRY DIMENSIONS Dévisseradapter-rescrew M Hauteur intérieure minimale de la cavité 27" (687) N Largeur intérieure de la cavité 22" (560) O Profondeur intérieure m
5B DIMENSIONS DE L’ARMOIRE – MURAL (ie INSTALLÉ AVEC UN FOUR COMPACT F&P) N Four compact O M 23 5/8" (600mm) Tiroir chauffant Four compact *PO HAUT LE CÔTÉ Tiroir chauffant Four compact M Trousse de garniture inférieure (en option, fournie séparément) Tiroir chauffant Espaceur de bois supplémentaire de 11/16" (18mm) Cabinet ci-dessous CABINETRY DIMENSIONS M Hauteur intérieure minimale de la cavité avec kit de garniture inférieur en option sans kit de garniture inférieur en option N Largeur
5C DIMENSIONS DE L’ARMOIRE – MURAL (ie INSTALLÉ AVEC UNE CAFETIÈRE F&P) IMPORTANT! Si vous installez sous la cafetière F&P, assurez-vous qu’il y a un espace de 2"(50mm) à l’arrière de l’armoire et une découpe de 7 7/8"2 (200mm2) pour le passage de l’air. Reportez-vous aux instructions d’installation du fabricant de café.
5D DIMENSIONS DE L’ARMOIRE – MURAL (STANDALONE) Support anti-basculement fourni (vissé sur la paroi arrière) IMPORTANT! Dans une installation murale autonome, vous devez vous assurer que le support antibasculement fourni est installé à moins qu’une étagère fixe agisse au-dessus comme un obstacle anti-basculement.
6 JETER L’EMBALLAGE DE MANIÈRE RESPONSABLE Déballez le tiroir chauffant et inspectez pour déceler tout signe de dommage. N’installez pas le tiroir chauffant s’il a été endommagé. IMPORTANT! Les matériaux d’emballage (sacs en plastique, mousse de polystyrène, agrafes, sangles d’emballage, etc.) et les outils ne doivent pas être laissés en place pendant et après l’installation, surtout s’ils sont facilement accessibles aux enfants, car ils peuvent causer des blessures graves.
9 FIXEZ LE TIROIR CHAUFFANT AUX ARMOIRES 1 Assurez-vous que le tiroir chauffant est de niveau et positionné dans la cavité. IMPORTANT! Ne soulevez pas le tiroir chauffant par la poignée du tiroir. 2 Ouvrez complètement le tiroir. 3 Fixez le tiroir chauffant en place avec les deux vis fournies, à travers la garniture avant, sous le tiroir. Ne pas trop serrer les vis.
FP WARMER DRAWER INTERFACE LOGIC_V1 !1 LISTE DE CONTRÔLE FINALE A REMPLIR PAR L’INSTALLATEUR F Assurez-vous que le tiroir-réchaud est de niveau et solidement fixé aux armoires. FP WARMER DRAWER INTERFACE LOGIC_V1 FP WARMER DRAWER INTERFACE LOGIC_V1 F Assurez-vous que tout emballage interne a été retiré du tiroir. F Assurez-vous que l’interrupteur d’isolement est accessible au client. 1h Assurez-vous que le support anti-basculement a été correctement installé si nécessaire.
MACHINE À CAFÉ Modèles EB24 560.00 12.95 00.00 20.
1 SÉCURITÉ ET AVERTISSEMENTS CONSIGNES DE SÉCURITÉ IMPORTANTES! ● ● Installation ● AVERTISSEMENT! Couper le danger Attention – certains bords sont coupants. Ne pas faire preuve de prudence peut entraîner des blessures ou des coupures. Vérification des dommages de transport Après avoir retiré l’emballage, assurez-vous que le produit est complet et non endommagé et que tous les accessoires sont présents. N’utilisez pas l’appareil s’il est visiblement endommagé. Contacter le service client.
2 Des vis (28) PIÈCES FOURNIES Agrafe (1) Rails (2) Espaceurs (4) pour le côté (4) pour le bas 3 ● ● ● ● ● ● ● ● ● AVANT L’INSTALLATION La cavité du comptoir et de la cafetière sont carrées et de niveau, et sont les dimensions requises. 560.00 L’installation sera conforme à toutes les exigences de dégagement et aux normes et règlements applicables. L’interrupteur d’isolement sera facilement accessible au client avec la cafetière installée. 352.
5 DIMENSIONS DU PRODUIT E H C F D LE CÔTÉ HAUT B I MODÈLES EB24 DIMENSIONS DU PRODUIT Pouces (mm) A Hauteur totale du produit A 18" (458) B Largeur totale du produit C 23 1/2" (596) Profondeur totale du produit (à l’exclusion des cadrans) 18 7/8" (480) D Hauteur du châssis 17 1/2" (445) E Largeur du châssis 22 1/16" (560) F Profondeur du châssis Avant 18 1/8" (460) G Profondeur du cadre de la cafetière et du panneau de commande H Panneau de contrôle Stepdown au châssis I Hauteur d
6A DIMENSIONS DE L’ARMOIRE (CAVITÉ DE 18 1/8" (460MM) DE HAUTEUR) Vérifiez les mesures minimales requises pour une installation correcte de l’appareil. La cafetière doit être installée dans une colonne et la colonne doit être fermement fixée au mur avec des supports disponibles dans le commerce. IMPORTANT! Toutes les opérations d’installation ou de maintenance doivent être effectuées avec l’appareil déconnecté du secteur.
6B DIMENSIONS DE L’ARMOIRE (KIT DE GARNITURE DE CAVITÉ DE 18 7/8" (480MM)) Vérifiez les mesures minimales requises pour une installation correcte de l’appareil. La cafetière doit être installée dans une colonne et la colonne doit être fermement fixée au mur avec des supports disponibles dans le commerce. Trousse de garniture inférieure Le kit Lower Trim montré est disponible à commander séparément auprès de fisherpaykel.com.
7 INSTRUCTIONS D’INSTALLATION " 0.07 ) m (1.8m environ 13 3/4" (350mm) 1 Positionnez les rails sur les côtés de l’armoire. Fixer avec les vis fournies, puis les extraire complètement. ● Si la cafetière est installée sur un tiroir chauffant, utilisez la surface supérieure comme référence pour positionner les rails. ● Dans ce cas, il n’y aura pas de surface sur laquelle reposer les rails. 2 Fixez le câble d’alimentation avec le clip.
8 LISTE DE CONTRÔLE FINALE A REMPLIR PAR L’INSTALLATEUR F Assurez-vous que la cafetière est de niveau et solidement fixée aux armoires. F Vérifiez que la garniture inférieure n’est pas endommagée. F Vérifiez qu’il y a un dégagement suffisant. Ceci afin d’assurer une circulation d’air correcte. F Assurez-vous que les attaches de câble et l’emballage interne ont été retirés de la cavité de la cafetière.
FOUR À VAPEUR Modèles OS24N 42.00 556.00 565.30 5 22.
1 SÉCURITÉ ET AVERTISSEMENTS Installation ● AVERTISSEMENT! Danger de choc électrique Avant d’effectuer tout travail sur la partie électrique de l’appareil, celui-ci doit être déconnecté du secteur. La connexion à un bon système de mise à la terre est absolument essentielle et obligatoire. Les modifications apportées au système de câblage domestique ne doivent être effectuées que par un électricien qualifié. Le non-respect de ce conseil peut entraîner un choc électrique ou la mort.
2 ● ● ● ● ● ● ● ● ● AVANT L’INSTALLATION Le comptoir et la cavité du four sont carrés et de niveau, et sont les dimensions requises. 560.00 L’installation sera conforme à toutes les exigences de dégagement et aux normes et règlements applicables. L’interrupteur d’isolement sera facilement accessible au client avec le four installé. 352.00 L’électricien fournit suffisamment de longueur libre du câble d’alimentation pour atteindre l’arrière de la cavité à au moins 59 1/16" (1.
4 DIMENSIONS DU PRODUIT E C F D G HAUT LE CÔTÉ H B MODÈLES OS24N DIMENSIONS DU PRODUIT A A Hauteur totale du produit 18" (458) B Largeur totale du produit 23 7/16" (596) C Avant Pouces (mm) Profondeur totale du produit (à l’exclusion de la poignée et des cadrans) 22 1/8" (562) D Hauteur du châssis 17 1/2" (445) E Largeur du châssis 21 7/8" (556) F Profondeur du châssis 21 1/4" (540) G Profondeur du cadre du four et du panneau de commande 7/8" (22) (=distance entre l’avant du ch
5A DIMENSIONS DE L’ARMOIRE (CAVITÉ DE 18 1/8" (460MM) DE HAUTEUR) Le four doit être installé sous une table de cuisson, dans une colonne ou combiné avec le tiroir-réchaud. Le matériau de l’armoire doit être capable de résister à la chaleur. Le four doit être centré dans les parois de l’armoire et fixé avec les vis et les bagues fournies.
5B ● ● ● DIMENSIONS DE L’ARMOIRE (KIT DE GARNITURE DE CAVITÉ DE 18 7/8" (480MM)) Le four doit être installé sous une table de cuisson, dans une colonne ou combiné avec le tiroir-réchaud. Le matériau de l’armoire doit être capable de résister à la chaleur. Le four doit être centré dans les parois de l’armoire et fixé avec les vis et les bagues fournies. Trousse de garniture inférieure Le kit Lower Trim montré est disponible à commander séparément auprès de fisherpaykel.com.
6 ● ● BRANCHEMENT ÉLECTRIQUE Avant de vous connecter à l’électricité, assurez-vous que: les spécifications du système électrique correspondent à ce qui est détaillé sur cette section. (Fig. 1) le système a une connexion au sol efficace conforme aux normes et lois en vigueur. La connexion au sol est requise par la loi. Le câble ne doit à aucun moment atteindre une température supérieure à 122 ° F (50 ° C) au-dessus de la température ambiante.
8 LISTE DE CONTRÔLE FINALE A REMPLIR PAR L’INSTALLATEUR F Assurez-vous que le four est de niveau et solidement fixé aux armoires. F Vérifiez que la garniture inférieure n’est pas endommagée. F Ouvrez lentement la porte du four jusqu’à ce qu’elle soit complètement ouverte et vérifiez qu’il y a un espace suffisant entre le bas de la porte et la garniture inférieure. Ceci afin d’assurer une circulation d’air correcte.
FOUR À MICRO-ONDES Modèles OM24N 42.00 556.00 565.30 35 22.
1 SÉCURITÉ ET AVERTISSEMENTS Installation ● AVERTISSEMENT! Danger de choc électrique Avant d’effectuer tout travail sur la partie électrique de l’appareil, celui-ci doit être déconnecté du secteur. La connexion à un bon système de mise à la terre est absolument essentielle et obligatoire. Les modifications apportées au système de câblage domestique ne doivent être effectuées que par un électricien qualifié. Le non-respect de ce conseil peut entraîner un choc électrique ou la mort.
2 ● ● ● ● ● ● ● ● ● AVANT L’INSTALLATION Le comptoir et la cavité du four sont carrés et de niveau, et sont les dimensions requises. 560.00 L’installation sera conforme à toutes les exigences de dégagement et aux normes et règlements applicables. L’interrupteur d’isolement sera facilement accessible au client avec le four installé. 352.00 L’électricien fournit suffisamment de longueur libre du câble d’alimentation pour atteindre l’arrière de la cavité à au moins 59 1/16" (1.
4 DIMENSIONS DU PRODUIT E C F D G HAUT H LE CÔTÉ B MODÈLES OM24N DIMENSIONS DU PRODUIT A A Hauteur totale du produit 18" (458) B Largeur totale du produit 23 7/16" (596) C Avant Pouces (mm) Profondeur totale du produit (à l’exclusion de la poignée et des cadrans) 22 1/8" (562) D Hauteur du châssis 17 1/2" (445) E Largeur du châssis 21 7/8" (556) F Profondeur du châssis 21 1/4" (540) G Profondeur du cadre du four et du panneau de commande 7/8" (22) (=distance entre l’avant du ch
5A DIMENSIONS DE L’ARMOIRE (CAVITÉ DE 18 1/8" (460MM) DE HAUTEUR) Le four doit être installé sous une table de cuisson, dans une colonne ou combiné avec le tiroir-réchaud. Le matériau de l’armoire doit être capable de résister à la chaleur. Le four doit être centré dans les parois de l’armoire et fixé avec les vis et les bagues fournies.
5B ● ● ● DIMENSIONS DE L’ARMOIRE (KIT DE GARNITURE DE CAVITÉ DE 18 7/8" (480MM)) Le four doit être installé sous une table de cuisson, dans une colonne ou combiné avec le tiroir-réchaud. Le matériau de l’armoire doit être capable de résister à la chaleur. Le four doit être centré dans les parois de l’armoire et fixé avec les vis et les bagues fournies. Trousse de garniture inférieure Le kit Lower Trim montré est disponible à commander séparément auprès de fisherpaykel.com.
6 ● ● BRANCHEMENT ÉLECTRIQUE Avant de vous connecter à l’électricité, assurez-vous que: les spécifications du système électrique correspondent à ce qui est détaillé sur cette section. (Fig. 1) le système a une connexion au sol efficace conforme aux normes et lois en vigueur. La connexion au sol est requise par la loi. Le câble ne doit à aucun moment atteindre une température supérieure à 122 ° F (50 ° C) au-dessus de la température ambiante.
8 LISTE DE CONTRÔLE FINALE A REMPLIR PAR L’INSTALLATEUR F Assurez-vous que le four est de niveau et solidement fixé aux armoires. F Vérifiez que la garniture inférieure n’est pas endommagée. F Ouvrez lentement la porte du four jusqu’à ce qu’elle soit complètement ouverte et vérifiez qu’il y a un espace suffisant entre le bas de la porte et la garniture inférieure. Ceci afin d’assurer une circulation d’air correcte.