Installation Guide
Table Of Contents
- ActiveSmart-int-ref-install-guide-RB2470BRV-849695C-USCA
- 1 Safety and warnings
- 2 Components list
- 3 Components list — Door panels and handles
- 4 Product dimensions
- 5 Cabinetry dimensions
- 6 Door opening rotation
- 7 Electrical specifications
- 8 Before installation
- 9 Unpacking and moving your product
- 10 Installation overview
- 11 Changing over door hinge (optional)
- 12 Install trim clips
- 13 Install cabinetry attachment brackets
- 14 Install clearance adjustment plates
- 15 Position your product inside the cabinetry
- 16 Fix your product inside the cabinetry
- 17 Install the trims
- 18 Install door panels (stainless steel)
- 19 Install top door panel (custom)
- 20 Install bottom door panel (custom)
- 21 Install covers and inlet vent grille
- 22 Final checklist
- ActiveSmart-int-ref-install-guide-RB2470BRV-849695C-FRCA
- 1 Consignes de sécurité et mises en garde
- 2 Liste des pièces
- 3 Liste des pièces — Panneaux de portes et poignées
- 4 Dimensions du produit
- 5 Dimensions des armoires
- 6 Rotation d’ouverture de la porte
- 7 Spécifications électriques
- 8 Avant l’installation
- 9 Déballage et déplacement de votre produit
- 10 Vue d’ensemble de l’installation
- 11 Changement de côté des charnières de porte (étape optionnelle)
- 12 Installation des clips de garniture
- 13 Installation des supports de fixation d’armoires
- 14 Installation des plaques d’ajustement de dégagement
- 15 Positionnement de votre produit dans les armoires
- 16 Fixation de votre produit dans les armoires
- 17 Installation des garnitures
- 18 Installation des panneaux de portes (en acier inoxydable)
- 19 Installation du panneau de porte supérieur (sur mesure)
- 20 Installation du panneau de porte inférieur (sur mesure)
- 21 Installation des couvercles et de la grille d’évent d’entrée d’air
- 22 Liste de vérification finale
19
!8 INSTALL DOOR PANELS (STAINLESS STEEL)
Installing the hanging and attachment brackets
3 Remove the rulers (B) from the top hanging
bracket and discard.
4 Align the screw holes of the top
hanging bracket with the screw holes of
the top door panel and fix the bracket
with supplied M5x12 screws (C).
5 Align the screw holes of the bottom
attachment bracket assembly (Bottom
attachment bracket, Side spacer
bracket, Bottom attachment strap) with
the screw holes of the top door panel,
and fix with M5x12 screws (D).
Attaching the door handle
6 Remove the plastic plugs from handle
holes (4x).
7 Align the handle to the holes and secure
with M5x25 hex screws (E).
E
C
Repeat steps 3 – 7 for the door panel
of freezer door.
D
B
Repeat steps 8 – !0 for the door panel of freezer door.
Note: The magnet sensor is installed only on the refrigerator door.
Hanging the door panel
8 Open the refrigerator door.
9 Hang the top door panel onto the height
adjustment nuts (F) at the top of the
refrigerator door.
F
Bottom view of door
!0 Align the bottom attachment
brackets with screw holes at the
bottom of the top door panel.
Fasten with bottom attachment
screws (G).
– Do not tighten fully to
allow adjustment of the
top door panel.
G