24” INTEGRATED REFRIGERATOR/FREEZER RB2470BRV model INSTALLATION GUIDE US CA 849695C 07.
TABLE OF CONTENTS 1 SAFETY AND WARNINGS 2 COMPONENTS LIST 3 COMPONENTS LIST — DOOR PANELS AND HANDLES 4 APPLIANCE DIMENSIONS 5 CABINETRY DIMENSIONS 6 DOOR OPENING ROTATION 7 ELECTRICAL SPECIFICATIONS 8 BEFORE INSTALLATION 9 UNPACKING AND MOVING YOUR APPLIANCE !0 INSTALLATION OVERVIEW !1 CHANGING OVER DOOR HINGE (OPTIONAL) !2 INSTALL TRIM CLIPS !3 INSTALL CABINETRY ATTACHMENT BRACKETS !4 INSTALL CLEARANCE ADJUSTMENT PLATES !5 POSITION YOUR APPLIANCE INSIDE THE CABINETRY !6 FIX YOUR APPLIANCE INSIDE THE CABIN
1 2 SAFETY AND WARNINGS ! WARNING! COMPONENTS LIST MI (miscellaneous items) pack — included in the appliance. Electric Shock Hazard Read and follow the safety and warnings outlined in this installation guide before operating this appliance. Failure to do so can result in death, electric shock, fire or injury to persons.
2 Pre-installed parts — included with the appliance. Top hanging bracket cover (2x) Hinge covers (4) Door gasket baffle* (2x) Trim installation fittings — included in the appliance. Top attachment ruler (4x) * Used only when transporting the appliance. Remove from the door after delivery of the appliance.
COMPONENTS LIST — DOOR PANELS AND HANDLES Door handle kits — not included with the appliance and must be purchased separately. Stainless Steel door panels — Fisher & Paykel (Stainless steel) door panel is not included with the appliance and must be purchased separately.
4 5 APPLIANCE DIMENSIONS CABINETRY DIMENSIONS E C D Door panel flush with side of cabinetry B A A E F PLAN VIEW B c FRONT VIEW SIDE VIEW D APPLIANCE DIMENSIONS A Overall height of appliance in (mm) 69 3/4” (1773) B Overall width of appliance 21 7/8” (555) C Overall depth of appliance (excluding door panels) 21 1/4” (540) d Height of top door (including top and bottom hinges) e Height of hinge gap f Height of bottom door (including top and bottom hinges) 42” (1066) 1/2” (12) 27 1/4”
6 DOOR OPENING ROTATION WARNING! ●● ●● Ensure that the appliance is stable before opening the doors. Ensure that you follow the instructions to avoid risks that can cause serious injury or death.
7 ELECTRICAL SPECIFICATIONS WARNING! Electric shock hazard! Assume all parts are live. Disconnect supply before servicing and installation. ●● Alternative area for electrical connection should be on the wall above the cabinetry. Left side of cavity Power cord (excl. plug) — 41 3/8” (1050mm) from top edge of appliance !! !! Electrical Electrical LEFT HAND SIDE 7 7/8” (200mm) RIGHT HAND SIDE Power cord (excl. plug) — 105 1/8” (2670mm) from right side edge of appliance Power cord (excl.
8 BEFORE INSTALLATION IMPORTANT! ●● ●● ●● ●● ●● Ensure your appliance is not exposed to any heat generating appliances eg cooktop, oven or dishwasher. The appliance must be installed by a qualified installer, or Fisher & Paykel trained and supported service technician to avoid faulty electrical connection. All connections for electrical power and grounding must comply with local codes and ordinances and be made by licensed personnel when required.
9 UNPACKING AND MOVING YOUR APPLIANCE IMPORTANT! ●● ●● ●● ●● ●● Be careful when unpacking to prevent damage to the surface of your appliance. Ensure that the appliance is stable to prevent from tipping over when unpacking. Do not open the doors to prevent the appliance from tipping over. If the appliance is damaged, contact your Fisher & Paykel dealer. Take note of your model and registration numbers located at the bottom right side of the appliance.
!0 INSTALLATION OVERVIEW a a Clearance adjustment plate b Bottom attachment bracket c D c Hanging bracket cover d Sensor magnet e Bottom attachment bracket cover (Custom door only) f f Top attachment ruler g Cabinetry attachment bracket cover h Cabinetry attachment bracket i Position adjustment plate j Door gasket baffle k m Wood screw l Bottom attachment bracket screw m Top hanging bracket j c f M j i h 10 e g l k b
!1 CHANGING OVER DOOR HINGE (OPTIONAL) This model is right hinged with a left-opening door. If required, you can change this model to left hinged with a right-opening door. C Right hand cover Hinge cover Left hand cover Remove the right hand cover by levering from the outer edge. Remove the hinge cover by levering from the inner edge. Remove the left hand cover by levering from the outer edge.
!2 A INSTALL TRIM CLIPS Cabinetry top inside surface A 5 1/8” (130mm) 5 1/8” (130mm) A B B Installing trim clips to the cabinetry 1 Install top trim clips (A) to the top inside surface of the cabinetry at a minimum clearance of 5 1/8” (130mm) from the top side edge of the cabinetry. 2 Install side trim clips (B) to the right and left side inner surfaces of the cabinetry. Drill each screw hole 9/16” (15mm) from the front edge of the cabinetry side (C).
!3 INSTALL CABINETRY ATTACHMENT BRACKETS Adjust the air flow stops Install cabinetry attachment bracket to the appliance 4 Adjust the air flow stops located on the back cover of the compressor. Ensure the air flow 1 Remove the pre-existing screw/plastic stops make contact with the cabinetry. washer (A) and plastic plugs (B) on the non-hinge side bottom corner of the appliance. IMPORTANT! It is possible for the air flow stops to get flattened during transport.
!4 INSTALL CLEARANCE ADJUSTMENT PLATES IMPORTANT! Clearance adjustment plates are installed depending on the overall dimensions of your cabinetry (see table for more information). 1 Attach clearance adjustment plates to the door hinges of the refrigerator and freezer doors. –– Ensure the correct orientation when attaching the plates.
!5 POSITION YOUR APPLIANCE INSIDE THE CABINETRY Connecting the appliance to the power supply Aligning the appliance inside the cabinetry 1 Move the appliance in front of the cabinetry close enough that you can access behind to connect the power supply. 3 Push the appliance all the way into the cabinetry and adjust its position. –– Ensure the front edges of all clearance adjustment plates (refrigerator and freezer doors) are flush with the cabinetry front edge (B).
!6 1 Fix the appliance to the cabinetry by screwing in all door hinges. FIX YOUR APPLIANCE INSIDE THE CABINETRY 2 Slide the cabinetry attachment bracket towards the cabinetry wall so that the position adjustment plate is pressed against the cabinetry wall, and then fix with a wood screw (A). A 3 Tighten the attachment bracket screws (B). B 4 Once the appliance is fixed into the cabinetry, break off the tab of the position adjustment plate (C).
!7 INSTALL THE TRIMS Top trim 1 Slide the LH and RH top corners (A) into the ends of the top trim (B). 2 Fix the top trim to the trim clips (C). A Note: You may need to cut the top trim depending on the overall dimensions of your cabinetry. (See table for more information). B A Top and bottom side trims (hinged side) 3 Slide the trim ends (D) to the top and bottom ends of each side trim (E). 4 Fix the side trims to the trim clips (C).
!8 INSTALL DOOR PANELS (STAINLESS STEEL) IMPORTANT! ●● ●● Ensure to protect the finish of the Fisher & Paykel Stainless steel door panels. Leave the protective film on the panels when hanging and remove the film only when the installation is complete. Removing the hanging bracket 1 Open the refrigerator door and remove the top hanging bracket cover by drawing out upwards.
!8 INSTALL DOOR PANELS (STAINLESS STEEL) Hanging the door panel Installing the hanging and attachment brackets B 3 Remove the rulers (B) from the top hanging 8 Open the refrigerator door. 9 Hang the top door panel onto the height bracket and discard. adjustment nuts (F) at the top of the refrigerator door. F 4 Align the screw holes of the top hanging bracket with the screw holes of the top door panel and fix the bracket with supplied M5x12 screws (C).
!8 INSTALL DOOR PANELS (STAINLESS STEEL) Fixing the top door panel Adjusting the door panel !6 Once you are satisfied with the adjustment, fully tighten the screws of the bottom attachment brackets (K) to secure the door panel. H I J L Height adjustment of the door panel !1 Turn the height adjustment nuts (H) with a hex key. Hold the side adjustment nuts (J) in place with a spanner to ensure it does not rotate when turning the height adjustment nuts.
!9 INSTALL TOP DOOR PANEL (CUSTOM) Removing the hanging bracket 1 Open the refrigerator door and Top of cabinetry 4 Push the rulers down so that remove the top hanging bracket cover by drawing out upwards. the underside of the overhang of the ruler is flush with the top of the cabinetry (A). Refrigerator door Flush A Ruler Side view ●● 2 Pull out the rulers from the ●● internal slots of the top hanging bracket and turn the rulers around.
!9 INSTALL TOP DOOR PANEL (CUSTOM) Installing the hanging and attachment brackets 6 Lay the top custom door panel (face down) onto the floor and place the top hanging bracket on the door panel. Latch the rulers on top of the door panel (D). D 7 Align the center line of the top hanging bracket with the center of the top door panel. 8 Once aligned, fix the top hanging bracket to the top door panel with wood screws. 9 Remove the rulers from the top hanging bracket and discard.
!9 Hanging the door panel INSTALL TOP DOOR PANEL (CUSTOM) Adjusting the door panel !0 Open the refrigerator door. !1 Hang the top door panel onto the height adjustment nuts (E) at the top of the refrigerator door. E J Height adjustment of the door panel !2 Align the bottom attachment brackets (F) with the screw holes at the bottom of the top door panel. Fasten with cabinetry attachment screws (G) and wood screws (H). –– Do not tighten fully to allow adjustment of the top door panel.
@0 INSTALL BOTTOM DOOR PANEL (CUSTOM) Removing the hanging brackets 1 Open the freezer door and remove the 4 Push the rulers down and close top hanging bracket cover by drawing out upwards. the freezer door. Adjust the rulers so that the top side of the overhang of each ruler contacts the bottom of the top door panel. (A). Freezer door Top door panel A 1/8” (3mm) gap Side view Internal slots 2 Pull out the rulers from the internal slots of the top hanging bracket and turn the rulers around.
@0 INSTALL BOTTOM DOOR PANEL (CUSTOM) Hanging the door panel Installing the hanging and attachment brackets 6 Lay the bottom custom door panel (face down) onto the floor and place the top hanging bracket on the door panel. Latch the rulers on top of the door panel (C). 7 Align the center line of the top hanging bracket with the center of the top door panel. 8 Once aligned, fix the top hanging bracket to the bottom door panel with wood screws. 9 Remove the rulers from the top hanging bracket and discard.
@0 INSTALL BOTTOM DOOR PANEL (CUSTOM) Fixing the bottom door panel Adjusting the door panel !8 Once you are satisfied with the adjustment, fully tighten the screws of the bottom attachment brackets (K) to secure the door panel. H K J I !9 Place the bracket covers Height adjustment of the door panel !3 Turn the height adjustment nuts (H) with a hex key. Hold the side adjustment nuts (J) with a spanner wrench to ensure it does not rotate when turning the height adjustment nuts.
@1 INSTALL COVERS AND INLET VENT GRILLE Reinstall the hanging bracket covers 1 Re-insert the hanging bracket covers onto the top hanging brackets. Installing the (optional) inlet vent grille 2 Install the inlet vent grille to the inlet vent at the toe kick section of the cabinetry. –– The grille can be purchased as an accessory.
@2 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models FF Check all parts are installed. FF Ensure the appliance is level. FF Ensure the appliance is securely fastened to the cabinetry with the supplied fittings. FF Ensure the doors can open and close freely with no resistance from surrounding cabinetry. FF Ensure all internal and external packaging is removed from the appliance before use. Complete and keep for safe reference: Model Serial No. Purchase Date FISHERPAYKEL.