JOINER KIT RF135B, RF170B & RF170W models INSTALLATION GUIDE US CA
COMPONENTS REQUIRED This kit is designed for use on 67 3/4"-high models and can be used to combine any variants of RF135B, RF170B and RF170W with handles. We recommend you save this installation guide for future reference.
PRODUCT DIMENSIONS – RF135B COMBINATIONS B PLAN ISOMETRIC C D PRODUCT DIMENSIONS E RF135B + RF135B IN MM A Overall height 67 3/4 1720 B Overall depth* 27 3/8 695 C Overall width 51 1295 D RF135B width 25 635 *Including rear compartment cover, excluding handle.
PRODUCT DIMENSIONS – RF170B/W COMBINATIONS B PLAN ISOMETRIC C D D A PRODUCT DIMENSIONS FRONT PROFILE RF170B/W + RF170B/W IN MM A Overall height 67 3/4 1720 B Overall depth* 27 3/8 695 C Overall width 63 1/8 1605 32 790 D RF170B/W width *Including rear compartment cover, excluding handle. 4 Actual product dimensions may vary by up to +3/16" (5 mm).
CAVITY DIMENSIONS – RF135B COMBINATIONS FLUSH - 90PROUD - FLUSH FULL - FULL PROUD - FULL FLUSH - 90 PROUD INSTALL PROUD - FULL FLUSH - 90 CAVITY DIMENSIONS FLUSHFLUSH - FULL - 90 FLUSH INSTALL FLUSHFLUSH - FULL - 90 FLUSH - 90PROUD - FLUSH FULL - FULL Full door rotation Full door rotation 90° door rotation a a a C C C B B B RF135B + RF135B RF135B + RF170B/W IN MM IN MM A Width of cavity 52 9/16 1335 58 5/8 1490 B Height of cavity 68 5/16 1735 68 5/16 C Depth of cavity 24
PROUD - FULL FLUSH - 90 CAVITY DIMENSIONS – RF170B/W COMBINATIONS FLUSH - 90 PROUD -FLUSH FULL - FULL PROUD INSTALL PROUD - FULL FLUSH - 90 CAVITY DIMENSIONS FLUSH INSTALL FLUSH -FLUSH FULL - 90 FLUSH - 90 PROUD -FLUSH FULL - FULL Full door rotation Full door rotation 90° door rotation a a a C C B B RF170B/W + RF170B/W IN MM A Width of cavity 64 3/4 1645 B Height of cavity 68 5/16 C Depth of cavity 24 3/8 6 FLUSH -FLUSH FULL - 90 CAVITY DIMENSIONS C B RF170B/W + RF170B/W IN M
PROUD - FULL CLEARANCES FLUSH - 90 PROUD INSTALL FLUSH - 90 PROUD - FULL FLUSH - 90 PROUD -FLUSH FULL - FULL FLUSH - FLUSH FULL - 90 FLUSH - 90 PROUD -FLUSH FULL - FULL FLUSH INSTALL FLUSH - FLUSH FULL - 90 Full door rotation a Full door rotation a a 90° door rotation a B A Side clearance B Rear clearance (incl.
INSTALLATION Before you begin z z z z z Check cavity dimensions are correct for the type of dual installation you require. Unpack appliances from packaging following guidance on individual cartons. Ensure the floor is protected from damage during unpacking and installation. Check that the Joiner Kit is complete. Always position the two appliances side-by-side with the door hinges on the far left and right, ensuring you have enough space to access the rear of the appliances.
INSTALLATION 6 Adjust front feet of both appliances until level. Turn clockwise to decrease height or anti-clockwise to increase height. IMPORTANT! Two people required. !0 Carefully tilt the connected appliances backwards to access the rear feet and the lower front bracket location. Washers 7 At the top of each appliance, remove the three screw caps using a flat-blade screwdriver. Remove the leveling feet from both appliances using a socket wrench by rotating them anti-clockwise.
INSTALLATION ADJUSTING DOOR ALIGNMENT 14 !4 14 14 Locate the centre trim panel assembly to the tab on the lower bracket. 3 1 !5 15 15 Position the centre trim panel under the upper bracket before re-tightening the six screws. !6 16 16 Secure the centre trim panel using the remaining 8x16 screw. !7 17 Close the doors and position the 1 within the cavity. appliances 15 16 10 2 2 2 Ensure front leveling feet are adjusted correctly. Incorrect leveling may affect door alignment.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2022. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.