INTEGRAL KIT ActiveSmart models RF331T, RF381T, RF411T, R440T, RF521T, RF373, RF450, E450, RF308, RF388, E388 Cabinet widths 525, 635, 680 and 790mm INSTALLATION GUIDE NZ AU
1 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS! WARNING! Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good earth wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death.
2 Rail slide (4) No. 880791 Screw (8) (#8X3/4 CSK POSI) No. 880796 PARTS SUPPLIED (PART NO. 814990) Bracket slide (4) No. 880792 Screw (2) (#8X30 CSK POSI) No. 880797 Foot integration (2) No. 880793 Screw (8) (#8X40 CSK POSI) No. 880798 Cap elliptical for foot integration (8) No. 880794 Screw (4) (#8X 1/2 PAN PH) No. 900373 Spacer 20mm (2) No. 880795 Plug (5) No. 880618 Ventilation Grille (1)* No.
3 INSTALLATION DIMENSIONS Cabinet construction Sample dimensions module 790, 522B The base of the cabinet must be level, eg a shim may be required to lift the rear. This diagram depicts the use of a ventilation grille. We recommend the use of this grille when integrating 790mm wide models. This grille is not included in the kit, but it can be ordered as Part No. 873917. Ceiling Airflow 75mm (3”) Airflow Note: See ‘Safety and Warnings’ (page 1) regarding air clearance and optimum performance.
4 CAVITY DIMENSIONS MODEL 635 E331T, RF331T RF373, RF308 E381T, RF381T E372B, RF372B E411T, RF411T E402B, RF402B E415H E450, E388, RF450, RF388 mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) A Width 735 (29”) 735 (29”) 735 (29”) 735 (29”) 735 (29”) 735 (29”) 735 (29”) 735 (29”) B Depth 730 (28 3/4”) 730 (28 3/4”) 730 (28 3/4”) 730 (28 3/4”) 730 (28 3/4”) 730 (28 3/4”) 730 (28 3/4”) 730 (28 3/4”) 1456 (57 3/8”) 1456 (57 3/8
5 BEFORE INSTALLATION 100mm (4”) 150mm (6”) Refrigerator and cabinet hinge side Prepare refrigerator for installation 1 Check that the internal cupboard dimensions are correct. Refer to ‘Product dimensions’ (page 4). 2 Unpack the refrigerator protecting the floor and/or paint work from damage. 3 Check that the refrigerator door is hinged on the side best suited for its position. Refer to the ‘User guide’ for instructions to change hinge side if required.
6 REMOVE REFRIGERATION HANDLES Remove door handles by undoing the screws as indicated here 2.75mm (1/8”) Allen key Remove the door handles ●● ●● ●● ●● After removing the door handles fit the small plugs (supplied) into the visible screw holes. Attach the spacers with the screws supplied to the side of the built-in cabinet on the side without hinges. Position approximately 100mm (4”) from the top front, 150mm (6”) from the front edge, and 75mm (3”) rear corners of the refrigerator cabinet.
7 DOOR CABINETRY PLACEMENT Placement — 110° full door rotation 20mm (3/4”) Placement — 90° door rotation 80mm (3 1/8”) 600mm (23 5/8”) 20mm (3/4”) 55mm (2 1/8”) Internal dimensions width of the built in cabinet 790, 680 or 635 models Internal cabinet width = Product width (790, 680 or 635) + 80mm (3 1/8”) hinge side clearance and 20mm (3/4”) hinge clearance door open side.
8 HINGE TYPES Door open Door closed Hinge Full overlay Butt hinge Insert door Half overlay Add 30mm (2”) to dimensions (A) and (B) refer ‘Cavity dimensions’ (page 4) Types of hinging that can be used 790, 680 or 635 models Hinges are available in a vast array of opening angles and overlay options. We recommend that 110˚ hinges having a low profile are used, either full or half overlay such as the GRASS brand. Use hinges that can carry a high load, especially when integrating 790 models.
9 FOOT LEVELLING 95mm (3 3/4”) to Gasket face Sample two-door fridge 1 Using two people, tilt the product back and remove the levelling foot circular base insert from the front levelling feet, a small flat blade screw driver can be used to lever and ‘pop out’ the central circular insert. 2 Lift the product into the cabinet. 9 3 Lift the front edge of the product and slide the integration foot under the levelling foot. 4 Push the product back to allow the outer cabinet door to close.
!0 ALIGN REFIGERATOR TO CABINETRY 20mm (3/4”) Sample flat door fridge 1 Slide the product toward the opening side of the cupboard. The integrated foot should touch the cupboard wall. This will set a 20mm (3/4”) gap between cupboard and refrigerator. 2 Adjust the product so it is parallel to the cabinet front to back and side to side. This is obtained by the adjustment of the front levelling feet.
!1 SECURE SLIDE BRACKET TO REFRIGERATOR DOORS Attach the slide bracket to the side of the door opposite to the hinges, 100mm (4”) in from the edge. Slide bracket 100mm (4”) 100mm (4”) 100mm (4”) Slide bracket Hinge side Slide bracket Slide bracket Double door Single door On a two-door refrigerator use one slide bracket per door. On a single door refrigerator use one slide bracket at each end of the door. Screw brackets firmly into the steel door face using the countersunk screw.
!2 SECURE SLIDE BRACKET TO CABINETRY DOOR 110° A 120mm (4 3/4”) B Screw slide bracket in level Complete Installation 1 Open both cupboard and refrigerator door to 110° (525 compact models to 90°). 2 Put the slide bracket into the retainer, 120mm (43/4”) approximately past refrigerator door (A). 3 Check that the screw supplied will not penetrate front surface of cupboard door (B). 4 Screw the slide bracket level into the cupboard door. 5 Check the slide mechanism does not bind through swing of door.
!3 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER FF Check the appliance is level and securely fitted to the cabinetry. FF Check all parts are installed. FF Ensure all internal and external packaging is removed from the appliance before use. FF Check that the isolating switch is accessible by the customer. FF If required, ensure the stability bracket has been fitted correctly. FF Ensure doors can open and close freely with no resistance from surrounding cabinetry.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. NZ AU 846233B 01.
