ACTIVESMART™ REFRIGERATOR CONTEMPORARY QUAD DOOR REFRIGERATOR FREEZER ICE & WATER RF605QDU, RF605QN, RF605QZ QUAD DOOR REFRIGERATOR FREEZER NON-ICE & WATER RF605QD INSTALLATION GUIDE NZ AU BI SG
SAVE THESE INSTRUCTIONS The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advise may result in death, electric shock, fire or injury to persons. • Read and follow the safety and warnings outlined in this guide before operating this appliance. ! WARNING! Risk of fire/flammable material This refrigerator contains flammable refrigerant isobutane (R600a).
ACTIVESMART™ REFRIGERATOR Quad Door Fridge Freezer, 905mm, 605L, Ice & Water Contemporary RF605QDU Quad Door Fridge Freezer, 905mm, 605L, Non-Ice & Water Quad Door Fridge Freezer, 905mm, 605L, Ice & Water Contemporary RF605QNU & RF605QZU RF605QD 4 Contemporary
SUPPLIED PARTS HANDLE KIT MISCELLANEOUS ITEMS PACK CONTEMPORARY The handle kit is not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information.
PRODUCT DIMENSIONS b C PLAN PRODUCT DIMENSIONS D A Overall height of product 1790 B Overall width of product 905 C Overall depth of product (excludes handle) 688 D Depth with door open – from rear of fridge – 90° rotation E Depth with door open – from flush with door – 90° rotation F G b FRONT 6 E C PROFILE 1084 396 F Height to top of chassis 1754 G Height to top of hinge cover 1775 Actual product dimensions may vary by ± 2 mm A MM
CABINETRY DIMENSIONS — PROUD CUTOUT CLEARANCES B C a a a b b C D CABINETRY DIMENSIONS* A Inside height of cavity** RF605QD RF605QN/QZ MM MM 1810 1810 1025 985 945 945 640 640 B Inside width z z 90° rotation*** full rotation C Overall depth MINIMUM CLEARANCE DIMENSIONS A Vent (above refrigerator cabinet or around top of cupboard) RF605QD RF605QN/QZ MM MM 50 50 100 60 20 20 30 30 N/A N/A 320 320 B Side clearance z z 90° rotation* full rotation C Rear clearance * Incl
CABINETRY DIMENSIONS — FLUSH CUTOUT CLEARANCES b b b a a a c C d CABINETRY DIMENSIONS A Inside height of cavity* RF605QD RF605QN/QZ MM MM 1810 1835 1105 1065 1105 1105 718 718 B Inside width z z 90° rotation** full rotation C Inside depth * Including minimum air clearances ** Measurement includes a feet increase of 10mm. ***For full drawer/shelf access, the doors need to be open past 90°. To avoid damaging the product ensure doors do not contact the adjacent cabinetry/wall.
UNPACKING AND MOVING YOUR APPLIANCE Check that your appliance is the correct model as per your order. Follow the steps below to move your appliance to the install location. Be careful when tilting the appliance forward/backward. Tape the door shut to prevent opening while moving the appliance. 1 Tilt the appliance slightly forward and Insert the hand truck between pallet and appliance. 2 Restrain the appliance with a strap.
BEFORE INSTALLATION ELECTRICAL CONNECTION Electrical connection must be within this space if located behind the appliance and must not protrude from the back wall. Alternative locations for connection at rear of cavity We recommend the use of an isolating switch that is easily accessible to the user after the refrigerator is installed. Please follow the installation steps below to ensure your appliance operates correctly. Power z z z z z z Install your appliance where the plug is easily accessible.
WATER CONNECTION (ICE & WATER MODELS) 1 Ensure the refrigerator is NOT plugged into a power supply. Locate the isolation tap for cold water connection (tee and tap fitting not supplied). 2 Locate the water fitting kit to complete water connection installation. 3 4 5 Tighten the compression nut until it is hand tight, then tighten one additional turn with a spanner. 6 Fasten the water tap adaptor to the isolation tap. Take care not to overtighten the water tap adaptor.
FLUSHING THE WATER FILTER (ICE & WATER MODELS) FLUSHING THROUGH THE WATER DISPENSER 1 Press the water dispenser pad to dispense 4L of water. Wait for 4 minutes before dispensing again. 2 Dispense 4L of water and then wait for another 4 minutes. There may be carbon residue dispensed together with water. This is not harmful, and is normal during the flushing process. 3 Dispense another 4L of water. This prevents excessive dripping of water from your dispenser.
POSITIONING YOUR REFRIGERATOR Your Fisher & Paykel ActiveSmart™ refrigerator is fitted with front and rear rollers to allow you to easily move your refrigerator forward and backward. Avoid moving your refrigerator sideways to prevent damaging the rollers or the floor covering surface. Your refrigerator will arrive with the front feet wound up to assist with moving the product into its final location.
COMPLETE INSTALLATION Before placing food in the fresh food or freezer compartments z z z z Remove all internal packaging. Ensure that all transit clips are removed from the refrigerator. These are small rubber stoppers located at the back of the shelves. Clean the inside of the appliance with a mix of warm water and a small amount of liquid detergent. Use a soft cloth to remove dust collected during manufacture and transport.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
