INTEGRATED COLUMN REFRIGERATOR & FREEZER RS2484S, RS2484SH, RS3084S, RS3084SH RS1884F, RS2484F & RS3084F REFRIGERATOR-FREEZER RS3084W & RS3084W WINE CABINET RS2484V INSTALLATION GUIDE US CA
CONTENTS Safety and warnings 4 Appliance preparation 31 Integrated refrigerator & freezer 5 Door panel preparation — Stainless steel panel 33 Integrated refrigerator-freezer 6 Door panel preparation — Custom panel 34 Integrated wine cabinet 6 Door panel preparation — Wine cabinet only 35 Supplied parts 7 Power and water supply connection 37 Required parts 8 Install water filter 38 9 Single installation — Align appliance into cabinetry 39 Single installation — Secure appliance into
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electrical shock or death. • Read and follow the safety and warnings outlined in this User guide before operating this appliance. READ AND SAVE THIS GUIDE WARNING! To avoid hazard, follow these instructions carefully before Installing or using this appliance. Please make this information available to the persons installing the appliance. z Assume all electrical parts are live.
SAFETY AND WARNINGS INTEGRATED REFRIGERATOR & FREEZER INSTALLATION z z z z z z z z z The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 220lbs (100kg) load. Ensure that the anti-tip bracket is installed correctly to prevent the possibility of the appliance tipping forward when the door is open. Ensure the door of the appliance is closed when rolling into the cabinetry.
INTEGRATED REFRIGERATOR-FREEZER 24" Refrigerator-Freezer RS2484WLU1, RS2484WLUK1, RS2484WRU1 & RS2484WRUK1 30" Refrigerator-Freezer RS3084WLU1, RS3084WLUK1, RS3084WRU1 & RS3084WRUK1 Left or Right hinged door available for each model.
SUPPLIED PARTS INSTALLATION KIT (INTERNAL BOX) TRIMS INSTALL KIT (EXTERNAL BOX) Door panel attachment kit Refrigerator or Freezer #8 x 16 Mush Washer Twin Thread Philips Screw Side bracket (7x) Bracket slider (7x) Side spacer bracket (7x) Anti-tip bracket assembly M5x12 Cross-head screw (35x) #8 x 16 Mush Washer Twin Thread Philips Screw Cabinet side trim (2x) Door panel side cover (2x) Wine Cabinet #10x40 Pan Head Philips Screw Anti-tip bracket (1x) Masonry plug (5x) 10-12x35mm #10x40 cros
SUPPLIED PARTS REQUIRED PARTS MISCELLANEOUS ITEMS (MI) PACK STAINLESS STEEL TOE KICK PANEL Not supplied and can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information. REFRIGERATOR & FREEZER INTEGRATED REFRIGERATOR REFRIGERATOR & FREEZER RS2484S, RS2484SH, RS3084SH & RS3084S RS2484S, RS2484SH, RS3084S, RS3084SH RS1884F, RS2484F & RS3084F Standard toe kick height is 4"(102mm) for standard stainless steel door panel.
DOOR PANEL KIT REFRIGERATOR OR FREEZER REFRIGERATOR-FREEZER Stainless steel door panel kit WINE CABINET Stainless steel door panel kit RH LH RS18 RD1884R4D RD1884L4D RS24 RD2484R4D RD2484L4D RS30 RD3084R4D RD3084L4D RH LH RS24 RD2484WRD RD2484WLD RS30 RD3084WRD RD3084WLD RS24 RH LH RD2484VR4 RD2484VL4 M5 x 14 Mush Head SS Philips Screw M5 x 14 Mush Head SS Philips Screw M5 x 14 Mush Head SS Philips Screw M5 x 14 Mush Head SS Philips Screw M5 x 14 Mush Head SS Philips Screw
HANDLE KIT CONTEMPORARY PROFESSIONAL Aluminium/Black square handle set CODES REFRIGERATOR/FREEZER WINE CABINET AHD3-RD84 REFRIGERATOR/FREEZER WINE CABINET AHV2-RD84 24" REFRIGERATOR-FREEZER AHD3-RD2484W 24" REFRIGERATOR-FREEZER AHV2-RD2484W 30" REFRIGERATOR-FREEZER AHD3-RD3084W 30" REFRIGERATOR-FREEZER AHV2-RD3084W Aluminium/Black square fine handle set MODEL CODES REFRIGERATOR/FREEZER WINE CABINET AHD5-RDSF REFRIGERATOR/FREEZER WINE CABINET AHC-RD84 24" REFRIGERATOR-FREEZER AHD5RD24
HINGE CHANGE KIT WINE DISPLAY ACCESSORIES Not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information. Select among the hinge change kit options below: HINGE KIT REFRIGERATOR OR FREEZER WINE CABINET Accessories are not supplied with the appliance. A wine display kit and a label kit are sold separately and can be purchased online at fisherpaykel.com.
TOOLS Required tools Supplied tools Not supplied and must be provided by the installer.
PRODUCT DIMENSIONS REFRIGERATOR OR FREEZER B REFRIGERATOR-FREEZER B C A WINE CABINET C B C A A G F D D FRONT E E E PROFILE FRONT D PROFILE FRONT 18" PROFILE 24" 30" PRODUCT DIMENSIONS IN MM IN MM IN MM A Overall height 84 2134 84 2134 84 2134 17 3/4 451 23 3/4 603 29 3/4 756 24 610 24 610 24 610 2 7/8 – 4 73 – 102 2 7/8 – 4 73 – 102 2 7/8 – 4 73 – 102 E Height from floor to bottom of Stainless steel door/drawer panel 4 102 4 102 4 102 F Height f
CABINETRY DIMENSIONS — SINGLE INSTALLATION D C Flush with front of cabinetry A PLAN E E D B D UNFRAMED Aligns appliance with cabinetry FRAMED Aligns appliance with frame of cabinetry ISOMETRIC 18" 24" 30" CAVITY DIMENSIONS IN MM IN MM IN MM A Overall height of cavity 84 2134 84 2134 84 2134 B Overall width of cavity 18 457 24 610 30 762 C Minimum overall depth of cavity* 25 635 25 635 25 635 d Minimum gap from edge of door panel to cabinetry 1/8 3 1/8 3 1/8
CABINETRY DIMENSIONS — MULTIPLE INSTALLATION DUAL INSTALL TRIPLE INSTALL C C A A B B DUAL INSTALL 42" 48" 54" 60" CAVITY DIMENSIONS IN MM IN MM IN MM IN MM A Overall height of cavity 84 2134 84 2134 84 2134 84 2134 B Overall width of cavity 42 1067 48 1220 54 1372 60 1524 C Minimum overall depth of cavity* 25 635 25 635 25 635 25 635 TRIPLE INSTALL 66" 72" 78" 84" 90" CAVITY DIMENSIONS IN MM IN MM IN MM IN MM IN MM A Overall height of cavity
STAINLESS STEEL DOOR PANEL DIMENSIONS — SINGLE INSTALLATION REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR-FREEZER A A A B B B C C C 18" DOOR PANEL DIMENSIONS D 24" 30" 24" 30" IN MM IN MM IN MM DOOR PANEL DIMENSIONS IN MM IN MM A Height of door panel 79 7/8 2029 79 7/8 2029 79 7/8 2029 A Height of top door panel 49 3/8 1254 49 3/8 1254 b Width of door panel 17 3/4 451 23 3/4 603 29 3/4 756 B Height of bottom drawer panel 30 3/8 772 30 3/8 772 3/4 19 3
CUSTOM DOOR PANEL DIMENSIONS — SINGLE INSTALLATION REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR-FREEZER A A A B B B C C C 18" DOOR PANEL DIMENSIONS D 24" 30" 24" 30" IN MM IN MM IN MM DOOR PANEL DIMENSIONS IN MM IN MM A Height of door panel 77 7/8 - 81 7/8 1978 - 2080 77 7/8 - 81 7/8 1978 - 2080 77 7/8 - 81 7/8 1978 - 2080 A Height of top door panel 49 3/8 1254 49 3/8 1254 b Width of door panel 17 3/4 451 23 3/4 603 29 3/4 756 28 3/8 - 32 3/8 721 - 822 2
CUSTOM DOOR PANEL DIMENSIONS — MULTIPLE INSTALLATION DUAL INSTALL TRIPLE INSTALL The illustrations below are examples of custom door panels of different combinations for dual installation. Minimum gaps of 1/8" (3mm) must be retained between door panel side edges and cabinetry regardless of door panel widths. C C The illustrations below are examples of custom door panels of different combinations for triple installation.
TOE KICK DIMENSIONS Custom toe kick options 2 7/8” (73mm) – 4” (102mm) toe kick clearance measured from rear of door panel A A 2” (51mm) toe kick height (with extra lower grille attached) A B B B SINGLE INSTALL DUAL INSTALL TRIPLE INSTALL 6” (152mm) toe kick height SINGLE INSTALL STAINLESS STEEL/CUSTOM PANEL A Height of toe kick* B Width of toe kick 18" A Height of toe kick* b Width of toe kick MM IN MM IN MM 2-6 50 - 152 2-6 50 - 152 2-6 50 - 152 17 7/8 454 23 7/8 606 29 7/8 7
INSTALLATION OPTIONS SINGLE INSTALL WALL MULTIPLE INSTALL WALL WALL WALL WALL WALL WALL WALL WALL WALL 4" (100mm) WALL WALL WALL WALL 2 3/8" (60mm) WALL WALL WALL WALL The illustrations above show acceptable installation options with reference to the door opening range and partition (optional). Be aware of clashing (circled) of doors or handles when opening at the same time.
DOOR CLEARANCE DRAWER CLEARANCE These dimensions apply to Refrigerator-Freezer models only. C B A A Wall LIMITED INTERNAL ACCESS FULL INTERNAL ACCESS B A Insert hinge limiting pin Before pushing the appliance into the cabinetry, insert the supplied hinge limiting pin into the borehole of the top and bottom/middle door hinges. The hinge limiting pin limits door swing to 90°.
ELECTRICAL AND PLUMBING Electrical connection must be within this space if located behind the appliance and must not protrude from the back wall.
CUSTOM DOOR PANEL INSTALL DIMENSIONS Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation, download the folder from http://thekitchentools.fisherpaykel.com. 8 7/8” (225mm) 2” (51mm) 2” (50mm) Ø1/16” (Ø2mm) REF 18x Pilot holes recommended for bracket attachment. (Do not penetrate front surface).
CUSTOM DOOR PANEL INSTALL DIMENSIONS 20” (508mm) Ø1/16” (Ø2mm) REF 22x Pilot holes recommended for bracket attachment. (Do not penetrate front surface). Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets. 3/4” (20mm) 3 1/2” (90mm) 2” (50mm) 50” (1270mm) 70” (1778mm) 3 1/2” (90mm) 3/4” (20mm) 2” (50mm) 77 7/8” – 81 7/8” (1978 – 2080mm) 22x Pilot holes recommended for bracket attachment. (Do not penetrate front surface).
CUSTOM DOOR PANEL INSTALL DIMENSIONS For Wine cabinet, the Custom door panel must leave the glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of this appliance. 5” (127mm) 11 7/8” (302mm) 8” (203mm) 7 7/8" (200mm) Ø1/16” (Ø2mm) REF 22x Pilot holes recommended for bracket attachment. (Do not penetrate front surface).
CUSTOM DOOR PANEL INSTALL DIMENSIONS Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. z The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. 11 7/8" (301.6mm) 2" (50mm) 2" (50.8mm) 1 1/4" (32.
CUSTOM DOOR PANEL INSTALL DIMENSIONS Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. 2" (50mm) 8" (203.2mm) 1 1/4" (32.6mm) Ensure handle is mounted 65mm from edge of panel to the centre — this will avoid interference with bracket.
BEFORE INSTALLATION Checking your cabinetry Check the dimensions of the cabinetry: height, width, depth, floor level, finished alcove returns. Refer to 'Cavity Dimensions' for the correct measurements. Check the power supply and water connections z z z z z z z Ensure that there is a separate power socket for each appliance. Avoid sharing the power point with other appliances to prevent accidental switching off of the appliance. For power requirements, refer to the information on the serial plate.
BEFORE INSTALLATION Removing pre-installed parts Moving your appliance Top trim Be careful when tilting the appliance forward/backward. Tape the door shut to prevent opening while moving the appliance. You need at least two persons to move this appliance. Disengage one end of the top trim from dual lock strips on the non-hinge side of the appliance. Slide the top trim out from the hinge pocket of the appliance. Top door cover Remove the brackets from the non-hinge side of the pallet.
CAVITY PREPARATION Anti-tip bracket assembly kit Attaching the anti-tip bracket For solid wall installation back wall 4 Anti-tip bracket (1x) Masonry plug (4x) overhead cabinetry Drill holes suitable to the size of the masonry plugs. Hammer 10x30mm masonry plugs into wall until flush. Fix bracket to wall with #10x40mm cross head screws, and screw tightly. Measure the height (A) of the attachment location from the floor to the alcove return.
APPLIANCE PREPARATION Tools Removing the hanging brackets M8 hex key M8 washer M8 nut Loosen the M8 screws by 1/8" (3mm). 3 1/2" (13mm) spanner 1/2" (13mm) socket wrench 1 Remove the M8 nut and M8 washer from the M8 screw at the top of the door using the supplied hex key and spanner. M8 screw 1/8" (3mm). For Refrigerator-Freezer: 2 Illustrations may differ from your purchased appliance. Remove the hanging bracket and set aside to use later.
APPLIANCE PREPARATION Install fasteners kit Attaching the barbed plugs Before rolling into the cavity, insert a barbed plug into the large holes at the top right and left sides of the appliance. Barbed plugs (2x) Cabinet depth alignment gauge (4x) The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance. Tools Cross-head screwdriver Attaching the depth alignment gauges Loosen the right and left screws at the top and bottom sides of the door.
DOOR PANEL PREPARATION — STAINLESS STEEL PANEL Door handle kit M5 x 25 M5x25 Hex screw (4x) Attaching the handle Attaching the brackets Remove the protective film around the handle attachment area before installing the handle. Protect the finish of the door panel to avoid damage or scratches to the surface. hanging bracket Door panel attachment kit side bracket For Refrigerator/Freezer/Wine cabinet Secure the top hanging bracket to the screw holes of the door panel with 8Gx16 Mush washer screws.
DOOR PANEL PREPARATION — CUSTOM PANEL Door handle kit Attaching the handle Attaching the brackets Refer to 'Custom door panel installation dimensions' page for correct screw hole positions on the door panel. Refer to 'Custom door panel installation dimensions' page for correct screw hole positions on the door panel.
DOOR PANEL PREPARATION — WINE CABINET ONLY Installation kit Attaching the long glass trims Glass trims are attached to cover the gap between the door panel and glass panel. hanging bracket Do not exceed pass this line Long trim (2x) long trim long trim Attach the peeled portion of the trim starting from the top of the flange on one side of the door panel cutout. Tools z red protective film Ensure the trim does not overlap the hanging bracket. Align the trim flush with inside edge of the flange.
DOOR PANEL PREPARATION — WINE CABINET ONLY Installation kit Short trim (2x) Attaching the short glass trims 1 short trim Place the short trim along the length of the top of door panel cutout across the top ends of the long trims. 3 short trim Attach the peeled portion starting from one end of flange perpendicular to top end of long trim. Tools long trim Cutter Cut both ends of the short trim to length. 2 Peel off a small portion of red protective film from the short edge.
POWER AND WATER SUPPLY CONNECTION Water fittings kit Connecting to water supply Ensure the door of the appliance is closed before rolling into the cabinetry. Push the appliance carefully towards the front of the cabinetry close enough to allow access at the back for power and water connection. Ensure an isolating tap is available if water supply is not easily accessible.
INSTALL WATER FILTER Freezer and Refrigerator with Ice & Water function Refrigerator-Freezer Keep the door closed and ensure the appliance is stable before installing the water filter to avoid risk of appliance tipping over. Keep the door closed and ensure the appliance is stable before installing the water filter to avoid risk of appliance tipping over. 1 Remove the packaging of the supplied water filter. 1 Pull the filter tool gently to dislodge from the front of the appliance.
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY Tools Pushing into the cabinetry Cross-head screwdriver 7 1/16" (180mm) Roll the appliance carefully into the cabinetry until the anti-tip bracket overlaps the back edge of the appliance. z z Ruler Ensure the bracket overlaps the appliance by a minimum 7 1/16" (180mm) for a secure hold. Be careful not to run over the water hose and power cord when rolling in the appliance.
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY Tools Adjusting the alignment in the cabinetry Cross-head screwdriver Powered driver (optional) 1 Front foot adjustment screw Clockwise turn of the front and rear adjustment screws raise the height of the appliance. Rear foot adjustment screw Counter-clockwise turn of the adjustment screws lower the height of the appliance.
SINGLE INSTALLATION — SECURE APPLIANCE INTO CABINETRY Install fasteners kit Securing the top brackets 8Gx16 Countersunk screw (6x) Fix the top brackets to the ceiling surface of the cabinetry with 8Gx16 countersunk screws. Tools Cross-head screwdriver Powered driver (optional) Securing the side brackets Fix the side brackets (2x) to the lower right and left sides of the cabinetry with 8Gx16 countersunk screws.
DOOR PANEL INSTALLATION Tools Hanging the door panel Cross-head screwdriver M4 hex key (1x) 1/2" (13mm) spanner (1x) 1 Hold the door panel at an angle from the top of the door and lower the screw holes of the hanging bracket onto the adjustment screws. . 3 Screw the M8 washer and nut to the adjustment screw and loosely tighten. 1/2" (13mm) socket wrench For Refrigerator-Freezer Repeat steps 1 - 3 for the top door and drawer panels.
DOOR PANEL INSTALLATION Tools Adjusting the height of door the panel Re-adjusing the door panel Ensure the side brackets are loosely screwed when adjusting the height of the door panel. Do not adjust the door panel height when the side brackets are screwed tight. This can generate friction which causes the hanging brackets to bend. Cross-head screwdriver Turn the adjustment screw to raise or lower the height of the door panel relative to the door.
DOOR PANEL INSTALLATION Tools Installing locking bracket TOE KICK INSTALLATION Adjusting mounting plate brackets Cross-head screwdriver Cutter M4 hex key (1x) REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR—FREEZER Loosen the screw at the bottom of the door, and slide the locking bracket out until it touches the panel. 13mm spanner (1x) 1 Refrigerator-Freezer The locking bracket is located at the bottom of the top door panel.
TOE KICK INSTALLATION Miscellaneous components Attaching the mounting plate mounting plate Re-attach the toe kick mounting plate to the plinth using same screws that were set aside previously. Air toe kick seal (1x) Toe kick install kit 1 air toe kick seal If toe kick depth is less than 3 5/8" (92mm), attach an air toe kick seal to the mounting plate. Peel off the adhesive tape of air toe kick seal and attach to the middle of the back side of the mounting plate.
GRILLES INSTALLATION Tools Attaching the top grille Refrigerator or Freezer/ Wine Cabinet Cutter Open the door, and secure both ends of the grille and behind the water filter hatch with #8x16 screws. Refrigerator-Freezer Reattach the top grille with #8x16 screws. top grille top grille Cross-head screwdriver Attaching the bottom grille Refrigerator or Freezer/ Wine Cabinet Re-attach the bottom grille via magnets. Refrigerator-Freezer Re-attach the bottom grille via magnets.
CARBON FILTER INSTALLATION The carbon filter is used for Wine Cabinet models only. Ensure the cover is completely closed to prevent hatch or filter from being damaged. Replacement filters (862755) can be purchased online from fisherpaykel.com or by calling Fisher & Paykel Customer Care. 1 AIR FLOW DIVIDER INSTALLATION The air flow divider blocks the air flow from bypassing the front of the bottom grille. Remove the packaging of the filter.
CABINET TRIMS INSTALLATION Trims install kit Installing cabinet side trims door hinge adhesive strip Dual adhesive strips are pre-attached at four locations along the side trims. z 1 Cabinet side trim (2x) trim Ensure the adhesive strips are pressed firmly to the cabinet side trims. Peel off the liners from the dual adhesive strips. z Position the trim at an angle on the throat of the door hinge. Ensure the adhesive surface is clean and free of dust or small particles.
DOOR COVERS & TRIMS INSTALLATION Trims install kit Re-installing the top cover (for all models) Remove the backing film of dual adhesive strips pre-attached to the top of the door. Ensure the magnet is in place before installing the top cover. trim cap Door panel side cover (2x) top cover notch For Refrigerator or Freezer/ Wine Cabinet Align the top cover to the top of the door. 1 magnet housing trim cap Clip the notch into the magnet housing, and the trim caps on top of the adhesive strips.
TOP TRIM & HINGE POCKET COVERS INSTALLATION installing the top trim (for all models) Slide one end of the top trim into the hinge pocket of the appliance. Press the other end to engage the dual lock strips on the non-hinge side of the appliance. top trim installing the hinge pocket covers (for all models) Follow the steps below to install the covers for the top, bottom or middle hinge pockets.
MULTIPLE INSTALLATION — APPLIANCE PREPARATION Install fasteners kit Attaching the central spacer to cabinetry Attaching barbed plugs and depth alignment gauges barbed plugs Barbed plugs (2) depth gauges locations A Before rolling into the cavity, insert the barbed plugs into large holes on the top right and left sides of both appliances. b Cabinet depth alignment gauges (4) 1 The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance.
MULTIPLE INSTALLATION — ALIGN FIRST APPLIANCE INTO CABINETRY Tools Pushing first appliance into the cabinetry min 7 1/16" (180mm) Ruler Roll the first appliance slowly into one side of the cabinetry until the anti-tip bracket overlaps the back edge of the appliance. 1 Ensure the bracket overlaps the appliance by a minimum 7 1/16" (180mm) for a secure hold. Refer to 'Attach the anti-tip bracket' for more information.
MULTIPLE INSTALLATION — SECURE FIRST APPLIANCE INTO CABINETRY Install fasteners kit Adjusting alignment of first appliance in cabinetry 8Gx16 Countersunk screw (6) 1 Rear foot adjustment screw Front foot adjustment screw Tools Securing the top brackets Turn the front and rear adjustment screws clockwise to raise height of the appliance and counter-clockwise to lower the height.
MULTIPLE INSTALLATION — ALIGN SECOND APPLIANCE INTO CABINETRY Tools Pushing into the cabinetry Push the second appliance to roll slowly into the other side of the cabinetry side by side with the first appliance. min 7 1/16" (180mm) Ruler 1 Ensure the bracket overlaps the appliance by a minimum 7 1/16" (180mm) for a secure hold. Refer to 'Install antitip bracket' for more information.
43453 M6 Washer M5 Washer MULTIPLE INSTALLATION — SECURE SECOND APPLIANCE INTO CABINETRY M5 x20 Cap Screw 248072 M6 x 12 Cap Screw 840371 8Gx16 Mush Washer M5x20 Cap screw (1) 847984 Top joiner fastener kit Securing the top brackets cap screw washer M5x16x1 Plain washer (1) 10 x 50 Dual Lock Bottom joiner fastener kit Secure the top caps of both appliances to the central spacer with M5x20 cap screw and washer.
MULTIPLE INSTALLATION — INSTALL CABINET TRIMS Tools Installing the center trim The center trim is installed after the top trims and grilles to the appliances. Aluminium center trim (1x) Dual adhesive strips (4x) 1 2 Four dual adhesive strips are pre-attached along the center trim. Peel off the liners from the dual adhesive strips. Position the trim between the throats of both appliances. Push and press the trim on the appliances/throat.
WINE DISPLAY FOR WINE CABINET (OPTIONAL) Handle assembly Cradle assembly Retainer blocks are pre-assembled at the bottom of both ends of the handle. A retainer block is pre-assembled at the bottom of each cradle. Use a spacer to correctly position the cradle and avoid wine bottles being too upright resulting in bottles tipping over. 1 Loosen the screws until the retainer blocks can be inserted between slats of display rack. 2 Align handle to the front end of display rack.
CHANGE THE DOOR HINGES (OPTIONAL) You have the option to switch the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation, and must be purchased separately. Ensure that you remove all the shelves, covers and trims from the appliance before changing the hinges. Take care not to damage the door.
CHANGE THE DOOR HINGES (OPTIONAL) Detaching the top door hinge A b C E D f Detaching the bottom door hinge — For Refrigerator & Freezer / Wine Cabinet a B d C E F E Do not remove! 1 Rotate the bottom hinge (A) outwards and remove bottom hinge pocket cover (B) using a flat head screwdriver in the slot. 2 Remove the hinge by unscrewing the M6x16 countersunk screws (2x) (C). 3 Open the water filter hatch on the bottom grille and unscrew the #8x16 screw (D) while holding the grille in place.
CHANGE THE DOOR HINGES (OPTIONAL) Moving the sensor housing Move the sensor housing to align the opposite hall sensor clip with the centre of the cabinet. 1 Unclip the hall sensor from the housing. 2 Unhook the interceptor board harness from sensor housing so harness is loose. 6 3 Remove the #8x16 screws (2x) from the sensor housing. 7 60 4 Reinstall the sensor housing using #8x16 screws (2x) into the pre-drilled holes in the cabinet top panel.
CHANGE THE DOOR HINGES (OPTIONAL) Re-attaching the top door hinge D e c A b f Re-attaching the bottom door hinge — Refrigerator or Freezer / Wine Cabinet 1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk screws (A) on the new hinge side at the other side of the appliance. 2 Install the new hinge pocket and alcove top bracket on the new hinge side using two (2x) M6x16 countersunk screws (B). z The new hinge pocket and top alcove bracket are supplied with the hinge kit.
CHANGE THE DOOR HINGES (OPTIONAL) Changing the top door brackets L A FIL L FIL F M6x10 hex screws Top hinge ILL NO F NO 1 Unscrew the M5x10 screws (4x) to remove the top adapter bracket from the top of the door (A). 2 Install the new top adapter bracket into the other side of the top of the door with M5x10 screws (4x) (B). ILL NO NO Reinstalling the door L FIL L FIL L IL OF N IF LL 1 Secure the door to the top hinge and bottom/middle hinge with M6x10 hex screws (4x).
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER ALL MODELS F Cabinet Level: Ensure the appliance is level and dimensions accurate. Refer to 'Cabinetry Dimensions, pages 14-15'. F Door opening sensor: Ensure the magnets at door are in place so door opening sensor works properly. Refer to 'Install trims', page 47. F Anti-tip: Ensure the appliance is securely supported to the cabinetry with the supplied anti-tip bracket and fittings.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2020. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
