INTEGRATED COLUMNS RS1884FJ, RS2484FJ, RS3084FJ, RS2484S & RS3084S models INSTALLATION GUIDE US CA 847985B 03.
TABLE OF CONTENTS 1 SAFETY AND WARNINGS 2 INTEGRATED COLUMNS 3 COMPONENTS LIST 4 PRODUCT DIMENSIONS AND SPECIFICATIONS 5 CABINETRY OPTIONS 6 CAVITY DIMENSIONS 7 DOOR AND TOE KICK PANEL DIMENSIONS 8 CUSTOM DOOR PANEL DIMENSIONS 9 DOOR OPENING ROTATION !0 ELECTRICAL AND PLUMBING !1 BEFORE INSTALLATION !2 UNPACKING AND MOVING YOUR PRODUCT !3 ATTACH THE ANTI-TIP BRACKET !4 CONNECT TO WATER AND POWER SUPPLY OR !5 SINGLE INSTALLATION !6 DUAL INSTALLATION !7 INSTALL WATER FILTER !8 INSTALL BRACKETS TO DOOR PA
1 2 SAFETY AND WARNINGS ! WARNING! INTEGRATED COLUMNS 18” (457mm) 24” (610mm) 30” (762mm) RS1884FJ RS2484FJ RS3084FJ RS2484S RS3084S Electric Shock Hazard Read and follow the safety and warnings outlined in this installation guide before operating this appliance. ! WARNING! Cut Hazard Take care — panel edges are sharp. Failure to use caution could result in injury or cuts. ! FREEZER Failure to do so can result in death, electric shock, fire or injury to persons.
3 COMPONENTS LIST Installation kit (847677) — included with the appliance Door panel attachment kit (848191) side bracket (6x) (838183) bracket slider (6x) (838201) side spacer bracket (6x) (846177) Anti-tip bracket assembly (843934) M4 hex key (1x) (844124) Install fasteners kit (848192) For SS door panels: 8Gx16 mush washer screw (30x) (840371) #8 x 16 Mush Washer Twin Thread Philips Screw #8 x 16 Mush Washer Twin Thread Philips Screw anti-tip bracket (1x) (843933) Supplied in separate bag 10x3
3 MI (miscellaneous items) pack — included with the appliance. COMPONENTS LIST Kickstrip installation kit — Fisher & Paykel (Stainless steel) toe kick is not included with the appliance.
3 COMPONENTS LIST Door panels Dual install joiner kit (CA: 24985) — included with the appliance (Freezer model only). Attached to back of appliance. Used for any of the dual install options shown below. Left/Right Fisher & Paykel (Stainless steel) door panel is not included with the appliance and must be purchased separately. Customers can supply their own Custom door panel to match their cabinetry.
3 COMPONENTS LIST Hinge change kit — not included with the appliance and must be purchased separately.
4 PRODUCT DIMENSIONS AND SPECIFICATIONS C A E B FRONT VIEW D PROFILE VIEW RS18 RS24 RS30 inches (mm) inches (mm) inches (mm) 84” (2134) 84” (2134) 84” (2134) 17 3/4” (451) 23 3/4” (603) 29 3/4” (756) 24” (610) 24” (610) 24” (610) Door clearance 20” (508mm) 26” (660mm) 32” (813mm) Weight (including packaging) 260lb (118kg) 302lb (137kg) 344lb (156kg) Hettich K05 Hettich K05 Hettich K05 PRODUCT DIMENSIONS A Overall height of product B Overall width of product C Overall depth of
5 CABINETRY OPTIONS FRAMELESS CABINETRY (Frameless: Aligns the product/s with the cabinetry) FRAMED CABINETRY (Framed: Aligns the product/s with the frame of the cabinetry) Frameless E Framed E D E D Note: Images shown for single install. These options are also applicable for dual install.
6 D CAVITY DIMENSIONS Note: These dimensions are intended for ‘Flush Installation’ only.
7 DOOR AND TOE KICK PANEL DIMENSIONS RS18 DOOR PANEL DIMENSIONS (STAINLESS STEEL) RS24 RS30 inches (mm) inches (mm) inches (mm) A Height of door panel 79 7/8" (2029) 79 7/8" (2029) 79 7/8" (2029) B Width of door panel 17 3/4” (451) 23 3/4" (603) 29 3/4" (756) C Depth of door panel (excluding door handle) 3/4” (19) 3/4” (19) 3/4” (19) DOOR PANEL DIMENSIONS (CUSTOM)* A Height of door panel 77 7/8” – 81 7/8” (1978 – 2080) 77 7/8” – 81 7/8” (1978 – 2080) 77 7/8” – 81 7/8” (1978 – 208
7 DOOR AND TOE KICK PANEL DIMENSIONS A A C C B B D E 2” toe kick height (with extra lower grille attached) E SINGLE INSTALL E DUAL INSTALL B D E E F 4” toe kick height 6” toe kick height 2 7/8” – 4” toe kick depth measured from the front of the door 11
CUSTOM DOOR PANEL DIMENSIONS Custom door panel dimensions 5” (127mm) 14 7/8” (378mm) 7/8” x Ø1/8” (22mm x Ø2mm) 3/4” (20mm) 2” (50mm) 20” (508mm) 2 3/8” (60mm) Do not place handle holes in marked areas to avoid clashing with panel attachment brackets 2” (50mm) 50” (1270mm) 70” (1778mm) 77 7/8” – 81 7/8” (1978 – 2080mm) ●● The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
8 5” (127mm) 2” (51mm) 2” (50mm) 3/4” x Ø1/8” 18mm x Ø2mm Do not place handle holes in marked areas to avoid clashing with panel attachment brackets 3/4” (20mm) 50” (1270mm) 3 1/2” (90mm) Do not place handle holes in marked areas to avoid clashing with panel attachment brackets 70” (1778mm) 2” (50mm) 2 3/8” (60mm) 77 7/8” – 81 7/8” (1978 – 2080mm) 2” (50mm) 3/4” (20mm) 2” (50mm) 7/8” x Ø1/8” (22mm x Ø2mm) 8 7/8” (225mm) 2” (50mm) 20” (508mm) 2” (51mm) 2” (50mm) 8” (203mm) 3 1/2” (90m
9 DOOR OPENING ROTATION Z C B A For 90° door swing a hinge limiting bolt is supplied with your appliance. This pin fits in the boreholes of the top hinge (Z). A WARNING! ●● ●● Wall 115° DOOR OPENING (FULL ROTATION) Wall 90° DOOR OPENING Before opening the doors, ensure that the appliance is stable. Follow these instructions to avoid risks that can cause serious injury or death. 1 Open door to 90°. 2 Align the hinge limiting bolt vertically with the bore hole.
!0 ELECTRICAL AND PLUMBING WARNING! ●● Electric shock hazard! Assume all parts live. Disconnect supply before servicing and installation. Left side of cavity B REAR OF CAVITY B A C Floor Electrical and water connections must be within this space if located behind the appliance and must not protrude from the back wall. Note: We recommend to use an isolating switch that is easily accessible to the user after the appliance is installed.
!1 BEFORE INSTALLATION IMPORTANT! ●● ●● ●● ●● ●● ●● Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven or dishwasher. The appliance has front and rear rollers for moving the appliance forward and backward. Do not move the appliance sideways to avoid damaging the rollers or the floor covering/surface.
!2 UNPACKING AND MOVING YOUR PRODUCT WARNING! IMPORTANT! ●● ●● ●● ●● ●● ●● ●● Be careful when unpacking to prevent damage to the surface of your appliance. Ensure that the appliance is stable to prevent from tipping over when unpacking. Do not open the doors to prevent the appliance from tipping over. The appliance is heavy and requires a minimum of 2 persons to unpack and install. Ensure that the feet of the appliance are retracted. If the appliance is damaged, contact your Fisher & Paykel dealer.
!3 ATTACH THE ANTI-TIP BRACKET IMPORTANT! Ensure the appliance/s is stable when the door/s is open. The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 220lb (100kg) load. If installed correctly, this will prevent the possibility of the appliance tipping forward, when the door/s is open.
!4 CONNECT TO WATER AND POWER SUPPLY WARNING! ●● ●● ●● ●● The water connection instructions below are intended only for the professional installer. WARNING — connect to potable drinkable water supply only. DO NOT install on line pressure above 120psi (827kPa) or below 22psi (150kPa). DO NOT use on hot water supply (100°F [38°C max.]). IMPORTANT! ●● ●● ●● ●● Old water fittings (hose-sets) should not be reused. The appliance includes a stainless braided water line hose.
!5 ●● ●● SINGLE INSTALLATION Required components/tools: 4x cabinet depth alignment gauges (847760) Phillips screwdriver Installing depth alignment gauges Note: The alignment gauges are only temporary and removable after installation. 1 Loosen the screws at the right and left, top and bottom corners of the door (A). 3 Attach the alignment gauges A so that the screw head passes through the keyhole (C).
!5 SINGLE INSTALLATION IMPORTANT! ●● ●● ●● Required components/tools: Phillips screwdriver or power driver (PH2 bit) at minimum torque setting ruler Ensure that the hose is not run over when moving the appliance/s to prevent damage and possible water leaks. Use low speed, low torque setting when using powered drill. Ensure power cord is not damaged during installation.
!5 SINGLE INSTALLATION IMPORTANT! ●● ●● ●● Ensure the doors are in line with the cabinetry front and the appliance is centered. All four corners of the appliance must be supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing.
!6 Dual installation includes two appliances installed side by side. Refer to ‘Cavity dimensions’ section for cabinetry overall width for dual install. A joiner kit is required for dual installation and is available through an authorized Fisher & Paykel dealer. Please visit fisherpaykel.com for more information.
!6 ●● ●● DUAL INSTALLATION Required components/tools: 4x depth alignment gauges (847760) Phillips screwdriver Installing depth alignment gauges Note: The alignment gauges are only temporary and removable after installation. 1 Loosen the screws at the right and left, top and bottom corners of the door (A). 3 Attach the alignment gauges A so that the screw head passes through the keyhole (C). C B 2 Locate the alignment gauge to the screws with the correct orientation (B).
!6 DUAL INSTALLATION IMPORTANT! Make sure that all feet engage the floor and evenly support the product. Tighten the adjustment screw with screwdriver (do not use powered driver). ●● Required components/tools: ruler Positioning and aligning the first appliance inside the cabinetry 5 Align the top cap of the first appliance flush with the front of the spacer (B). 6 Mark the step (C) of each alignment gauge based on the thickness of the door panel to be 1 Coil the water hose flat behind the appliance.
!6 DUAL INSTALLATION IMPORTANT! ●● ●● Ensure the doors are in line with the cabinetry front and the appliance is centered. All four corners of the appliance must be supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing.
!6 ●● DUAL INSTALLATION Required components/tools: ruler Positioning and aligning the second appliance inside the cabinetry A C D 1 Roll the second appliance into the cabinetry side by side with the first appliance. (A) 2 Continue rolling the appliance into the cabinetry until the anti-tip bracket overlaps [minimum 7 1/8” (180mm)] the back top surface of the appliance. (Refer to ‘Attach the antitip bracket’). 3 Check the clearance between the floor and the feet.
!6 DUAL INSTALLATION IMPORTANT! ●● ●● Ensure the door is in line with the cabinetry front and the appliance is centered. All four corners of the appliance must be supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing.
!6 ●● Required components/tools: top joiner fastener kit (848313) –– 1x M5x20 cap screw (847984) –– 1x M5x16x1 plain washer (611307) ●● DUAL INSTALLATION Bottom joiner fastener kit (848312) –– 1x M6x16 washer screw (848869) –– 2x M6x12x3.
!7 ●● ●● 1 2 3 4 5 6 INSTALL WATER FILTER Required components/tools: 1x water filter (847200) 1x water filter removal tool (included with appliance) Remove the water filter packaging. Pull the filter tool gently to dislodge from the front of the appliance (A). Insert the water filter all the way into the filter casing and press firmly until the filter head is pushed further inside the casing (B). Using the filter tool, rotate the filter head 90° to lock in place (C).
!8 INSTALL BRACKETS TO DOOR PANEL (STAINLESS STEEL) IMPORTANT! ●● Ensure to protect the finish of the Fisher & Paykel Stainless Steel door panels. Leave the protective film on the panels when hanging and remove the film only when the installation is complete.
!9 INSTALL BRACKETS TO DOOR PANEL (CUSTOM) IMPORTANT! ●● ●● ●● Required components/tools: Door panel attachment kit (847678) –– 6x side panel brackets (838183) –– 6x bracket slider (838201) –– 6x panel bracket spacer (846177) –– 30x M5x12 Phillips screws (845432) (for Custom door panel only) drill with 3/32” (2.55mm) bit powered driver (Phillips) M4 hex key (supplied) Ensure the screw pilot holes do not penetrate the full depth of the panel.
@0 IMPORTANT! ●● ●● ●● The assembly of Fisher & Paykel (Stainless steel) door panels and Custom door panels are outlined below. Ensure to protect the finish of the Fisher & Paykel Stainless steel door panels. Leave the protective film on the panels when hanging. Remove the film only when the installation is complete. If using Custom door panels, ensure they are prepared as per ‘Custom door panel dimensions’ section.
@0 ●● ●● ●● INSTALL DOOR PANELS Required components/tools: 1x Phillips screwdriver M4 hex key 1/2” (13mm) spanner Fix the locking brackets Adjust the door panel Note: All door panels have full axis adjustment to ensure they are flush with adjacent walls. 1 To adjust the height of the door panel relative to the door, use M4 hex key to turn the top M8 screw (A) clockwise to lower or counter-clockwise to raise the door panel until the gap with the cabinetry above is 1/8” (3mm).
@1 INSTALL TOE KICK IMPORTANT! Two magnets are pre-installed to the bottom corners of the toe kick mounting plate. Each magnet has double-sided tape to be attached to the toe kick. This allows both Stainless steel and Custom panels to be attached to the magnet.
@2 ●● ●● ●● ●● INSTALL KICKSTRIP GRILLE IMPORTANT! Required components/tools: hex key (supplied) 1x fixed (top) grille 1x bottom (movable) grille 8x16mm pan head screws ●● ●● ●● ●● For toe kick heights 4 1/2” – 5” (114 – 127mm), shorten the lower grille by cutting along the vertical ribs. For 2” (51mm) toe kick height, an additional lower grille can be ordered. For toe kick heights greater than 5” (127mm), lower grille is not required. Refer to ‘Door and toe kick panel dimensions’ for more information.
@3 ●● INSTALL CABINET TRIMS Required components/tools: 1x alcove side trim assembly (848193) Install the side trims Note: Four (4) dual-lock strips are pre-installed along each side trim. 1 Peel off the liners from the dual-lock strips. (A) 3 Slide the trim behind the lower hinge (C), then the top hinge (D). Hold the same angle when sliding the trim. 4 Slot trim in behind top hinge pocket (E), then press (F) adhesive to cavity ensuring trim is also tight against appliance inner face.
@3 ●● Required components/tools: 1x top trim ●● INSTALL CABINET TRIMS Required components/tools: 1x center trim Install the center trims (for dual install only) Install the top trim 1 Slide the top trim into hinge pocket of the cabinet (A), Note: Four (4) dual-lock strips are pre-installed along the center trim. and then engage the dual lock at the non-hinge side (B). 1 Peel off the liners from the dual-lock strips. (C) 2 Position the trim between the throats of both cabinets.
@4 INSTALL FLOW DIVIDER AND DOOR TRIMS IMPORTANT! The door flow divider is pre-assembled to the door of the appliance. It blocks the air flow from bypassing in front of the bottom grille.
@5 OPTIONAL — CHANGING OVER DOOR HINGES You have the option to change the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation. ●● ●● IMPORTANT! ●● Ensure that you remove all the shelves, covers and trims from the appliance before changing the hinges. Take care not to damage the door. We recommend to lay the appliance (door closed) onto its back on the pallet when removing the door hinges.
@5 ●● ●● OPTIONAL — CHANGING OVER DOOR HINGES Required components/tools: star T20 screwdriver flat head screwdriver A Removing the top door hinge B 1 Rotate the top hinge (A) outwards and remove 2 3 4 5 the top hinge pocket cover (B) using the flat head screwdriver in the slot of the cover. Remove the hinge by unscrewing the M5x12 pan head screws (2x) (C), and set aside for later use. Remove the hinge pocket and top alcove bracket by unscrewing M5x12 pan head screws (2x) (D) from the hinge pocket.
@5 ●● ●● OPTIONAL — CHANGING OVER DOOR HINGES Required components/tools: star T20 screwdriver flat head screwdriver Moving the sensor housing (RS18 & RS24 only) E D A B F C G 1 Unclip the reed switch from the housing (A). 2 Unhook the interceptor board harness from sensor housing so harness is loose (B). 3 Remove the #8x16 screws (2x) from the sensor housing (C). 4 Move the sensor housing so that the opposite reed switch clip is aligned with the center of the cabinet (D).
@5 ●● Required components/tools: left/right hinge change kit (refer to ‘Components list’ for part numbers) –– 1x top (fixed) grille assembly –– hinge change assembly ●● ●● OPTIONAL — CHANGING OVER DOOR HINGES star T20 screwdriver flat head screwdriver E C Top hinge installation D 1 Reinstall the hinge top bracket and bracket 2 3 4 5 spacer with M5x12 countersunk screws (A) on the new hinge side at the other side of the appliance.
@5 ●● ●● Required components/tools: 2x K05 top adapter bracket RH (842935), LH (841982) 2x K05 bottom adapter bracket RH (842890), LH (842889) ●● ●● OPTIONAL — CHANGING OVER DOOR HINGES star T20 screwdriver Flat head screwdriver Door brackets 1 Remove the top adapter bracket from the top of the door by unscrewing M5x10 screws (4x) (A). 2 Install the new top adapter bracket into the other side of the top of the door with M5x10 screws (4x) (B).
@5 ●● ●● ●● OPTIONAL — CHANGING OVER DOOR HINGES Required components/tools: star T20 screwdriver flat head screwdriver hex driver Door installation 1 Reinstall the door to the appliance by fixing M6x10 hex screws (4x) into the hinges (A). 2 Activate the hinge spring by turning the star T20 screws to the “I” position (B). A B Top hinge A Bottom hinge 3 Return the appliance to the upright position. 4 Reinstall all covers and trims.
@6 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the door/drawer can open and close freely with no resistance from surrounding cabinetry. Ensure hinge limiting bolt is fitted for 90° door swing. Ensure all internal and external packaging is removed from the appliance before use.
