ACTIVESMART™ INTEGRATED REFRIGERATOR FREEZER RS36W80 and RS9120W models DUAL INSTALLATION GUIDE NZ AU GB IE HK SG IN US CA
CONTENTS 1 SAFETY AND WARNINGS 2 DUAL INSTALLATION 3 COMPONENTS 4 CAVITY DIMENSIONS 5 ATTACH BRACKET ASSEMBLY TO CAVITY 6 ATTACH FOAM PADS 7 REMOVE HINGE BRACKET 8 ATTACH CAVITY BRACKET 9 POSITION INTO THE CABINETRY !0 ATTACH CENTRE TRIM !1 INSTALL TOE KICK 1
1 2 SAFETY AND WARNINGS ! DUAL INSTALLATION Dual installation refers to the joining of one left hinge and one right hinge model using a joiner kit (sold separately). ●● Use RS91W joiner kit to pair 1 x RS91WR model with 1 x RS91WL model. ●● Use RS80 joiner kit to pair 1 x RS36WR model with 1 x RS36WL model. WARNING! This appliance is top-heavy and must be secured to prevent the possibility of tipping forward.
3 COMPONENTS Dual install joiner kit Not supplied and must be purchased separately Joiner bracket (1) Cavity fixing bracket (1) Right hinge cavity bracket (1) Left hinge cavity bracket (1) Foam pads (6) Centre trim (1) Toe kick (1) Bottom joiner bracket (1) M8 nut (1) Spring clips (6) M8 Nut M5 x 12 SHCS M5x12 Socket head (Socket Head Cap Screw) (11) cap screw M8 Screw Set M8 set screw (1) 8x16 mush washer screw (5) M5 x 12 SHCS (Socket Head Cap Screw) M8 Screw Set #8 x 16 Mush Washer T
4 CAVITY DIMENSIONS B A RS36W80 / RS9120W CAVITY DIMENSIONS in mm Overall height of cavity A for appliance using RD3680/RD9120 door panel set for appliance using RD3684/RD9121 door panel set B Overall width of cavity 84” 2134 80” 2032 72” 1829 5
5 ATTACH BRACKET ASSEMBLY TO CAVITY IMPORTANT! ●● ●● Ensure the anti tip brackets are installed before attaching the cavity fixing bracket. Refer to separate ‘Installation guide’ supplied with your appliance. Ensure the water and power supply are already connected, and door panels installed before attaching the cavity fixing bracket. Attach top joiner bracket and fixing bracket to cavity 1 Attach the top joiner bracket to the cavity fixing bracket with M5x12 socket head cap screws.
6 ATTACH FOAM PADS Attaching foam pads to appliance 1 Mark three locations along the edge of the non-hinge side of each appliance. Refer to the measurements table below. MEASUREMENTS in mm A Distance of first tab location from cabinet top 2” 50 B Distance of second tab location from cabinet top 35” 890 c Distance of third tab location from floor 13” 50 A IMPORTANT! Foam pads should be placed at identical heights on left and right hinge appliances to ensure good fit of joiner trim.
7 REMOVE HINGE BRACKET IMPORTANT! Follow these steps to remove the hinge bracket on the non-hinge side of both left and right hinge appliances. 2 At the non-hinge side of the appliance, loosen the M5x10 pan head attachment screws from the end of the top trim, and then shift the screws towards the centre of the trim. (A) Removing hinge brackets from appliance 1 Measure the distance between the end of the top trim and the side of the cabinet. ●● Ensure the distance is not greater than 1/4” (6mm).
8 ATTACH CAVITY BRACKET IMPORTANT! Follow these steps for fitting the cavity bracket on the non-hinge side of both left and right hinge appliances. Attaching cavity bracket to appliance A 1 Screw the cavity bracket with two M5x8 countersunk Phillips screws (A) to the location where the hinge bracket was removed. ●● Ensure that the top face of the front trim is parallel to the appliance. 2 Shift the M5x10 pan head Phillips screws into the slots in the cavity bracket. (B).
9 POSITION INTO THE CABINETRY IMPORTANT! ●● ●● DO NOT install the appliance on a soft, uneven, or unlevelled floor to avoid twisting the appliance and poor door sealing. If using a Powered driver, use low torque setting to avoid damaging the height adjustment system. ●● ●● Ensure that the top, bottom and sidge gaps are not greater than 1/16" (1.5mm) to achieve correct alignment.
!0 ATTACH CENTRE TRIM Preparing the centre trim Attaching the centre trim between appliances 1 Remove the M10x65 socket head cap screws from the base of the appliances. (A) 1 Open both appliance doors. Position the centre trim in front of the gap between the two appliances. (G) 2 Starting from the upper spring clips, squeeze the clips to slot between the two appliances (H). 2 Attach the bottom joiner bracket using M10 x 65 Socket head cap screws.
!1 INSTALL TOE KICK Installing the toe kick 1 Loosen the screws (A) of the toe kick bracket mid-way, and pull the bracket slightly outward (B). A Do this step for both appliances. B 2 Place toe kick over the brackets and position the outer brackets (C) until flush with surrounding cabinetry. ●● Use the folded edge of the supplied toe kick or another suitable straight edge to align the inner brackets (D). C D D C 3 Once aligned, remove the toe kick.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The appliance specifications in this document apply to the specific appliances and models described at the date of issue. Under our policy of continuous appliance improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the appliance currently available. NZ AU GB IE HK SG IN US CA 845689C 07.
