ACTIVESMART™ INTEGRATED REFRIGERATOR FRAMED AND FRAMELESS CABINETRY RS36W and RS91W Models DUAL INSTALLATION GUIDE NZ AU GB IE HK SG IN US CA
FOLLOW THE INSTALLATION SEQUENCE 1 Safety and warnings 3 2 Dual Installation 3 3 Components list 4 4 Alcove dimensions 5 5 Attaching foam pads 5 6 Removing hinge bracket and fitting alcove bracket 6 7 Attaching top joiner bracket and alcove fixing bracket to alcove 7 8 Location of products into alcove — Right product 8 9 Location of products into alcove — Left product 9 !0 Preparing for centre trim !1 Attaching the centre trim and toe kick 10 11 1
1 2 SAFETY AND WARNINGS ! DUAL INSTALLATION Dual installation refers to the joining of 1 x RS91WR model with 1 x RS91WL model or 1 x RS36WR model with 1 x RS36WL model. WARNING! This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. To ensure that the appliance is stable under all loading conditions, the anti-tip bracket and fittings supplied must be installed according to the following installation instructions by a professional installer.
3 COMPONENTS LIST Included with the Dual Install kit.
4 5 ALCOVE DIMENSIONS ATTACHING FOAM PADS 1 Measure and attach foam pads to three locations down the right side of the left hinge refrigerator. (Align the top of the foam pad to your measurement mark. Align the side of the foam pad with the front edge of the cabinet). B ●● ●● ●● 2” (50mm) from the cabinet top. 35” (890mm) from the cabinet top. 13” (50mm) from the floor. Repeat on the left side of the right hinge product.
6 REMOVING HINGE BRACKET AND FITTING ALCOVE BRACKET Start with the left hinge refrigerator and repeat the process on the right hinge refrigerator. Removing hinge bracket Follow the steps below to remove the hinge bracket (non hinged side) and fit the alcove bracket. This process is required for both left and right hinge refrigerators. <1/ 4” (<6 mm ) Fitting alcove bracket 4 Screw the front two M5 x 8 countersunk Phillips screws (refer to C).
7 ATTACHING TOP JOINER BRACKET AND ALCOVE FIXING BRACKET TO ALCOVE 1 Use M5 x 12 Socket head cap screws to connect the top joiner bracket to the alcove fixing bracket. – For 80” (2032mm) installation, use the upper slots of the alcove fixing bracket (refer to A). – For 84” (2134mm) installation, use the lower slots of the alcove fixing bracket (refer to B). 3 For flush installation measure 1 1/4” (108mm) back from the front face of the adjacent cabinetry doors (refer to C).
8 LOCATION OF PRODUCTS INTO ALCOVE — RIGHT PRODUCT 1 Roll the right hinge refrigerator into the right hand side of the alcove until the refrigerator makes contact with the joiner bracket. IMPORTANT! For flush installation: check for flushness of the refrigerator with the surrounding cabinetry (refer to separate ‘Installation guide’ booklet supplied with your refrigerator) on how to achieve flushness.
9 LOCATION OF PRODUCTS INTO ALCOVE — LEFT PRODUCT IMPORTANT! 2 Open the left hinge refrigerator door to access the brackets (refer to B). Open the door of the right hinge refrigerator. 1 Roll the left hinge refrigerator into the left hand side of the alcove until the refrigerator makes contact with the joiner bracket (refer to A).
!0 PREPARING FOR CENTRE TRIM 1 Remove the centre* M10 x 65 Socket head cap screws from the base of the refrigerators (refer to A) *Remove the right screw from the left hinge refrigerator. *Remove the left screw from the right hinge refrigerator. 5 Insert right hand spring clip into the centre trim channel (refer to C). IMPORTANT! Ensure the bottom of the right hand spring clip is located on the right hand side of the channel.
!1 ATTACHING THE CENTRE TRIM AND TOE KICK IMPORTANT! 6 Installing toe kick Unscrew the toe kick bracket screws mid-way, and bring forward (refer to D and E). Open both refrigerator doors. Repeat this process for both refrigerators. 1 Bring the centre trim in front of the gap between the two refrigerators (refer to A). D A E 7 Place toe kick over the brackets and position the outer brackets until flush with surrounding cabinetry.
FISHERPAYKEL.COM DCSAPPLIANCES.COM © Fisher & Paykel Appliances 2017. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. NZ AU GB IE HK SG IN US CA 845689 B 07.