INTEGRATED COLUMNS RS4621F, RS6121F, RS7621F, RS6121S & RS7621S models INSTALLATION GUIDE NZ AU GB EU 849164D 05.
CONTENTS 1 SAFETY AND WARNINGS 2 INTEGRATED COLUMNS 3 COMPONENTS 4 TOOLS 5 DUAL INSTALL OPTIONS 6 APPLIANCE DIMENSIONS AND SPECIFICATIONS 7 CABINETRY OPTIONS 8 CAVITY DIMENSIONS 9 DOOR AND TOE KICK PANEL DIMENSIONS !0 CUSTOM DOOR PANEL DIMENSIONS !1 DOOR CLEARANCE !2 ELECTRICAL AND PLUMBING DIMENSIONS !3-A ELECTRICAL AND PLUMBING SPECIFICATIONS (FOR NZ & AU ONLY) !3-B ELECTRICAL AND PLUMBING SPECIFICATIONS (FOR GB & EU ONLY) OR !4 BEFORE INSTALLATION !5 CAVITY PREPARATION !6-A WATER AND POWER SUPPLY CONN
2 SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Read and follow the safety and warnings outlined in this installation guide before operating this appliance. Failure to do so can result in death, electric shock, fire or injury to persons. ! 457mm 610mm 762mm RS4621F RS6121F RS7621F RS6121S RS7621S WARNING! WARNING! This appliance is top-heavy and must be secured to prevent the possibility of tipping forward.
3 COMPONENTS Installation kit Packaged in box located inside the appliance Miscellaneous components Door panel attachment kit Side bracket (6) Each supplied separately Bracket slider (6) Side spacer bracket (6) Air toe kick seal (1) Flow divider cap (1) Filter cartridge tool (1) #8 x 16 Mush Washer Twin Thread Philips Screw #8 x 16 Mush Washer Twin Thread Philips Screw For SS door panels: 8Gx16 Mush washer screw (30) For Custom door panels: M5x12 Cross-head screw (30) Anti-tip bracket assembl
3 COMPONENTS Water filter install kit (for NZ & AU only) (included in Miscellaneous items pack of Freezer models only) Miscellaneous items pack Located inside the appliance INTEGRATED COLUMNS INTEGRATED COLUMNS RS4621F, RS6121F, RS7621F, RS4621F, RS6121F, RS7621F, RS6121S & RS7621S models RS6121S & RS7621S models SERVICE & WARRANTY SERVICE ET GARANTIE ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ SERVIZIO E GARANZIA SERVICE & GARANTIE HUOLTO JA TAKUU INSTALLATION GUIDE SERVICE OG GARANTI 保修和维修 USER GUIDE NZ AU GB EU 服
5 Nut 39107 M6 Washer 843453 3 COMPONENTS Dual install joiner kit (CA: 25328) Used to install two appliances (refrigerator and freezer) side by side. Located in Freezer models only. Taped to the back of the freezer. Can be purchased separately through an authorised Fisher & Paykel dealer. Visit fisherpaykel.com for more information.
3 4 COMPONENTS Hinge change kit Not included with the appliance and must be purchased separately MODEL LEFT HINGE TO RIGHT HINGE TOOLS Required tools Not included with appliance Powered driver Flathead screwdriver Ruler Hacksaw Cross-head screwdriver Pencil Cutter T2 star-head screwdriver RIGHT HINGE TO LEFT HINGE RS46 848186 848185 RS61 848188 848187 RS76 848190 848189 Each kit includes: Hinge change assembly (1x), Top (fixed) grille assembly (1x) Hinge change assembly Hinge (ri
5 DUAL INSTALL OPTIONS The following are options for dual installation with reference to the door opening range and partition (optional) between two appliance combinations. IMPORTANT! ●● ●● Beware of clashing (circled) when opening the doors. Use a hinge limiting pin to restrict door opening rotation to 90°. Refer to ‘Door Clearance’ (page 15) for more information.
6 APPLIANCE DIMENSIONS AND SPECIFICATIONS C A A B B FRONT VIEW PROFILE VIEW RS46 APPLIANCE DIMENSIONS C RS61 RS76 mm mm mm A Overall height of appliance 2134 2134 2134 B Overall width of appliance 451 603 756 C Overall depth of appliance (excluding front door panel) 610 610 610 508 660 813 118kg 137kg 156kg Hettich K05 Hettich K05 Hettich K05 APPLIANCE SPECIFICATIONS Door clearance Weight (including packaging) Door hinge 8
7 CABINETRY OPTIONS FRAMELESS CABINETRY Aligns the appliance/s with the cabinetry E FRAMED CABINETRY Aligns the appliance/s with the frame of the cabinetry E D E D E D D Note: Images shown for single install. These options are also applicable for dual install.
D 8 CAVITY DIMENSIONS C C Flush with front of cabinetry D A A EE EE DD DD Frameless: finished return cavity sides and top Framed: finished return cavity sides and top B B PLAN VIEW Note: These dimensions are intended for ‘Flush Installation’ only.
9 DOOR AND TOE KICK PANEL DIMENSIONS A A C C B B B D E SINGLE INSTALL DOOR PANEL DIMENSIONS (STAINLESS STEEL) D DUAL INSTALL E RS46 RS61 RS76 mm mm mm A Height of door panel 2029 2029 2029 B Width of door panel 451 603 756 C Depth of door panel (excluding door handle) 19 19 19 1978 – 2080 1978 – 2080 1978 – 2080 451 603 756 DOOR PANEL DIMENSIONS (CUSTOM)* A Height of door panel B Width of door panel — single install C Depth of door panel Width of door panel —
9 E 51mm toe kick height (with extra lower grille attached) E DOOR AND TOE KICK PANEL DIMENSIONS E F 102mm toe kick height 152mm toe kick height 73 – 102mm toe kick depth measured from the from rear of door panel SINGLE INSTALL TOE KICK DIMENSIONS D RS76 mm mm mm mm 454 606 759 1064 DUAL INSTALL RS46 / RS76 RS61 / RS61 RS61 / RS76 RS76 / RS76 mm mm mm mm 1216 1216 1368 1521 F Height of toe kick# Stainless steel panel Custom panel** F RS61 Width of toe kick Stainless steel
CUSTOM DOOR PANEL DIMENSIONS Custom door panel dimensions 378mm Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com.
!0 CUSTOM DOOR PANEL DIMENSIONS 302mm 50mm 51mm 18mm x Ø2mm 50mm Do not place handle holes in marked areas to avoid clashing with panel attachment brackets 20mm 1778mm 50mm 50mm Do not place handle holes in marked areas to avoid clashing with panel attachment brackets 1978 – 2080mm 1778mm 1978 – 2080mm 60mm 50mm 50mm 60mm 33mm 14 33mm 603mm 450.
!1 DOOR CLEARANCE Z C B A A For 90° door swing a hinge limiting bolt is supplied with your appliance. This pin fits in the boreholes of the top hinge (Z). WARNING! ●● ●● Wall 115° DOOR OPENING (FULL INTERNAL ACCESS) Wall 90° DOOR OPENING Before opening the doors, ensure that the appliance is stable. Follow these steps to avoid risks that can cause serious injury or death. 1 Open door to 90°. 2 Align the hinge limiting bolt vertically with the bore hole. 3 Insert the pin through the bore hole.
!2 ELECTRICAL AND PLUMBING DIMENSIONS IMPORTANT! ●● ●● Electrical and water connections for these appliances must be located in an adjacent area or unit (cabinet or cupboard) that is easily accessible in case of repair or disconnection. Once installed, the service technician will NOT remove the appliance from the cavity to gain access for repair. WARNING! ●● ●● Electric shock hazard! Assume all parts live. Disconnect supply before servicing and installation.
!3-A ELECTRICAL AND PLUMBING SPECIFICATIONS (FOR NZ & AU ONLY) ELECTRICAL SPECIFICATIONS FREEZER REFRIGERATOR Supply 230 VAC, 50 Hz 230 VAC, 50 Hz Service 10 amp circuit 10 amp circuit Socket 3-pin earthing-type 3-pin earthing-type Power cord (total length)* 2000mm 2000mm PLUMBING SPECIFICATIONS* FREEZER REFRIGERATOR Supply 12.
!3-B ELECTRICAL AND PLUMBING SPECIFICATIONS (FOR GB & EU ONLY) ELECTRICAL SPECIFICATIONS FREEZER REFRIGERATOR Supply 230 VAC, 50 Hz 230 VAC, 50 Hz Service 10 amp circuit 10 amp circuit Socket 3-pin earthing-type 3-pin earthing-type Power cord (total length)* 2000mm 2000mm PLUMBING SPECIFICATIONS* FREEZER REFRIGERATOR Supply 1/4” (6.
!4 BEFORE INSTALLATION IMPORTANT! ●● ●● ●● ●● ●● ●● Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven or dishwasher. The appliance has front and rear rollers for moving the appliance forward and backward. Do not move the appliance sideways to avoid damaging the rollers or the floor covering/surface.
!4 BEFORE INSTALLATION IMPORTANT! ●● ●● ●● ●● ●● ●● ●● the appliance. (Preferably, non-hinged side of the appliance.) packaging carton. Cut along the cut lines and remove the carton and EPS (Expanded Polystyrene) foam. 2 Remove pre-packed install parts taped to the back panel of the appliance. 2 Tilt the appliance 3 Insert the hand truck slightly to the opposite side. under from the side of the appliance where the brackets were removed.
!5 Anti-tip bracket assembly kit IMPORTANT! ●● ●● ●● Anti-tip bracket (1) CAVITY PREPARATION Ensure the door of the appliance is closed when rolling into the cabinetry. DO NOT attempt to open the door until the appliance is fully installed. The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 100kg load. Ensure that the anti-tip bracket is installed correctly to prevent the possibility of the appliance tipping forward when the door is open.
!6-A IMPORTANT! Water fittings kit (Ice and Water models only) WATER AND POWER SUPPLY CONNECTION (FOR NZ & AU ONLY) ●● ●● ●● ●● WARNING! Old water fittings (hose-sets) should not be reused. The appliance includes a stainless braided water line hose. The shut off valve should be accessible. Make sure each appliance is connected to a separate power socket. ●● ●● ●● ●● The water connection steps below are intended only for the professional installer.
!6-B IMPORTANT! Water fittings kit (Ice and Water models only) WATER AND POWER SUPPLY CONNECTION (FOR GB & EU ONLY) ●● ●● ●● ●● Old water fittings (hose-sets) should not be reused. The appliance includes a stainless braided water line hose. The shut off valve should be accessible. Make sure each appliance is connected to a separate power socket. WARNING! ●● ●● ●● ●● The water connection steps below are intended only for the professional installer.
!7 Install fasteners kit SINGLE INSTALLATION Installing depth alignment gauges Note: The alignment gauges are only temporary and removable after installation. Cabinet depth alignment gauge (4) A Tools C Cross-head screwdriver 3 Attach the alignment gauges so that the screw 1 Loosen the screws at the right and left, head passes through the keyhole (C). top and bottom corners of the door (A). B B 2 Locate the alignment gauge to the screws with the correct orientation (B).
!7 IMPORTANT! Install fasteners kit ●● ●● ●● Barbed plug (2) Tools SINGLE INSTALLATION Ensure that the hose is not run over when moving the appliance/s to prevent damage and possible water leaks. Use low speed, low torque setting when using a powered driver. Ensure power cord is not damaged during installation. Aligning the appliance inside the cabinetry Positioning the appliance inside the cabinetry 1 Coil the water hose flat behind the appliance.
!7 SINGLE INSTALLATION IMPORTANT! Tools ●● ●● Ensure the doors are in line with the cabinetry front and the appliance is centred. All four corners of the appliance must be supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing. IMPORTANT! ●● ●● Make sure to remove the depth alignment brackets before fixing the appliance inside the cabinetry.
!8 IMPORTANT! Install fasteners kit ●● ●● ●● ●● Cabinet depth alignment gauge (1) Top joiner bracket kit DUAL INSTALLATION Dual installation applies to two appliances to be installed side by side. A joiner kit is required and located in the Freezer model only. The joiner kit is also available for purchase through an authorised Fisher & Paykel dealer. Visit fisherpaykel.com for more information.
!8 Install fasteners kit DUAL INSTALLATION Installing depth alignment gauges Note: The alignment gauges are only temporary and removable after installation. Cabinet depth alignment gauge (4) A Tools C Cross-head screwdriver 1 Loosen the screws at the right and left, top and bottom 3 Attach the alignment gauges so that the screw corners of the door (A). head passes through the keyhole (C).
!8 DUAL INSTALLATION IMPORTANT! Install fasteners kit ●● ●● Barbed plug (2) Make sure that all feet engage the floor and evenly support the appliance. Tighten the adjustment screw with screwdriver (do not use powered driver). Positioning and aligning the first appliance inside the cabinetry 1 Coil the water hose flat behind the first appliance. (Refer to ‘Connect to Tools 2 3 Ruler 4 5 water and power supply’).
!8 IMPORTANT! Install fasteners kit ●● ●● ●● 8Gx16 Countersunk screw (5) Tools Cross-head screwdriver DUAL INSTALLATION Ensure the doors are in line with the cabinetry front and the appliance is centred. All four corners of the appliance must be supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing.
!8 Install fasteners kit DUAL INSTALLATION Positioning and aligning the second appliance inside the cabinetry Barbed plug (2) C Tools Ruler 5 Align the top cap of the second appliance flush with the central spacer and top cap of first appliance (C). A D B 1 Before rolling the second appliance, insert a barbed plug into a large hole on the cabinetry side of the appliance to protect the inside of the cabinetry from being damaged by screws on the side of the appliance (B).
!8 IMPORTANT! Tools ●● ●● ●● Cross-head screwdriver DUAL INSTALLATION Ensure the door is in line with the cabinetry front and the appliance is centred. All four corners of the appliance must be supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting and poor door sealing.
M5 Washer M5 x20 Cap Screw 847984 M6 x 12 Cap Screw 248072 Dual install joiner kit !8 8Gx16 Mush Washer 840371 M5x20 Cap screw (1) DUAL INSTALLATION Fixing the second appliance inside the cabinetry 1 Fix the top caps of first and second appliances to the central spacer with the top joiner fastener kit (A). 2 Fix the bottom joiner brackets of both appliances together with the bottom joiner kit (B).
!9 Water filter install kit WATER FILTER INSTALLATION IMPORTANT! ●● The water filter head must be firmly pushed into the appliance and secured. incorrect installation can lead to water leaks. Install the water filter Water filter (1) Tools Flushing the water filter 1 Remove the water filter packaging. 2 Pull the filter tool gently to dislodge from the front of the appliance (A).
@0 DOOR PANEL INSTALLATION (STAINLESS STEEL) IMPORTANT! Door handle kit ●● M5 x 25 ●● Ensure to protect the finish of the Fisher & Paykel Stainless Steel door panels. Leave the protective film on the panels when hanging and remove the film only when the installation is complete. M5x25 Hex screw (4x) Attach the door handle Remove hanging bracket Door panel attachment kit 4 Remove the plastic plugs from handle 1 Remove the M8 washer and M8 nut from holes (x4).
@0 Tools DOOR PANEL INSTALLATION (STAINLESS STEEL) Hang the door panel 1 Remove the gauges and retighten the screws. Cross-head screwdriver Open the door and loosen the screws at both sides of the door (do not remove) (A). 2 Hang the door panel with a small angle to the door by locating the holes of the top bracket to the M8 studs (B), and rotate the door panel down so that the side attachment brackets slide onto the side screws of the door.
@1 DOOR PANEL INSTALLATION (CUSTOM) IMPORTANT! Door handle kit ●● M5 x 25 ●● ●● Ensure the screw pilot holes do not penetrate the full depth of the panel. Do not place the handle holes in marked areas to avoid clashing with panel attachment brackets. Minimum panel thickness where screw hole is drilled must be 16mm.
@1 DOOR PANEL INSTALLATION (CUSTOM) IMPORTANT! Tools ●● If using Custom door panels, ensure they are prepared as per ‘Custom door panel dimensions’ section. Hang the door panel Cross-head screwdriver 1 Remove the gauges and retighten the screws. Open the door and loosen the screws at both sides of the door (do not remove) (A). B 2 Hang the door panel with a small angle to the door by locating Powered driver/drill (with 2.
@2 Miscellaneous components TOE KICK INSTALLATION IMPORTANT! Two magnets are pre-installed to the bottom corners of the toe kick mounting plate. Each magnet has double-sided tape to be attached to the toe kick. This allows both Stainless steel and Custom panels to be attached to the magnet. Install the toe kick mounting plate and toe kick Air toe kick seal (1) Toe kick install kit 1 Reattach the toe kick mounting plate (A) to the plinth with 8x16mm cross-head screws.
@2 Toe kick grilles TOE KICK INSTALLATION Adjusting the toe kick grille Attach the top and bottom grilles 1 Loosen the cap screws of the adjustment brackets from both 4 Reinstall the top (fixed) grille (C) using the same screws set aside sides of the plinth using a hex key (A). 2 Adjust the toe kick to the desired depth by moving it forward/ backward (B). 3 Re-tighten the cap screws of the adjustment brackets on both sides using the hex key.
@3 Install parts CABINET TRIMS INSTALLATION Install the side trims 2 Position the trim on the Note: Four (4) dual-lock strips are pre-installed along each side trim. throat with an angle (B). 1 Peel off the liners from the dual-lock strips (A).
@3 Dual install joiner kit CABINET TRIMS INSTALLATION Install the centre trims (for Dual install only) Reinstall the top trim 1 Slide the top trim into hinge pocket of the cabinet (A), Note: Four (4) dual-lock strips are pre-installed along the centre trim. and then engage the dual lock at the non-hinge side (B). A Centre trim (1) D B C Dual-lock strip (4) 1 Peel off the liners from the dual-lock strips (C). 2 Position the trim between the throats of both cabinets (D).
@4 Miscellaneous components DOOR TRIMS INSTALLATION IMPORTANT! The door flow divider is pre-assembled to the door of the appliance. It blocks the air flow from bypassing in front of the bottom grille. ReInstall the flow divider Flow divider cap (1) Install the door trims 1 Peel the adhesive layer off the flow divider (A). 2 Remove the 8Gx16 countersunk screw from the bottom 1 Reinstall the door panel top extrusion to the of the door and re-install the flow divider using the same screw.
@5 OPTIONAL — CHANGING OVER DOOR HINGES You have the option to change the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation. Tools IMPORTANT! ●● ●● Ensure that you remove all the shelves, covers and trims from the appliance before changing the hinges. Take care not to damage the door. We recommend to lay the appliance (door closed) onto its back on the pallet when removing the door hinges.
@5 Tools OPTIONAL — CHANGING OVER DOOR HINGES Removing the top door hinge 1 Rotate the top hinge (A) outwards and remove 2 T2 star-head screwdriver 3 4 Flat-head screwdriver 5 the top hinge pocket cover (B) using the flat head screwdriver in the slot of the cover. Remove the hinge by unscrewing the M5x12 pan head screws (2x) (C), and set aside for later use. Remove the hinge pocket and top alcove bracket by unscrewing M5x12 pan head screws (2x) (D) from the hinge pocket.
@5 Tools OPTIONAL — CHANGING OVER DOOR HINGES Moving the sensor housing (RS46 & RS61 only) T2 star-head screwdriver E D A Flat-head screwdriver B F C G 1 Unclip the reed switch from the housing (A). 2 Unhook the interceptor board harness from sensor housing so harness is loose (B). 3 Remove the #8x16 screws (2x) from the sensor housing (C). 4 Move the sensor housing so that the opposite reed switch clip is aligned with the centre of the cabinet (D).
@5 Hinge change assembly OPTIONAL — CHANGING OVER DOOR HINGES Top hinge installation 1 Reinstall the hinge top bracket and bracket 2 Hinge (right or left) top pocket (1) 3 Lower (right or left) hinge bracket (1) 4 5 K05 top (right or left) adapter bracket (1) E C A D B E H Bottom hinge installation 6 Install a new lower hinge bracket on the new Top (fixed) grille assembly 7 Top (fixed) grille (1) spacer with M5x12 countersunk screws (A) on the new hinge side at the other side of the applia
@5 Hinge change assembly OPTIONAL — CHANGING OVER DOOR HINGES Door brackets 1 Remove the top adapter bracket from the top of the door by unscrewing M5x10 screws (4x) (A). 2 Install the new top adapter bracket into the other side of the top of the door with M5x10 screws (4x) (B). K05 top adaptor bracket R/L (1) 3 Remove the door panel locking bracket and washer from the bottom of the door by unscrewing M6x25 screw (1x) (C).
@5 Tools OPTIONAL — CHANGING OVER DOOR HINGES Door installation 1 Reinstall the door to the appliance by fixing 2 Activate the hinge spring by turning the M6x10 hex screws (4x) into the hinges (A). star T20 screws to the I position (B). T2 star-head screwdriver A Flat-head screwdriver B Top hinge Hex key A Bottom hinge 3 Return the appliance to the upright position. 4 Reinstall all covers and trims.
@6 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the door/drawer can open and close freely with no resistance from surrounding cabinetry. Ensure hinge limiting bolt is fitted for 90° door swing. Ensure all internal and external packaging is removed from the appliance before use.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The appliance specifications in this booklet apply to the specific appliances and models described at the date of issue. Under our policy of continuous appliance improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the appliance currently available. NZ AU GB EU 849164D 05.
