INTEGRATED COLUMN REFRIGERATOR & FREEZER RS6121S, RS6121SH, RS7621S, RS7621SH RS4621F, RS6121F & RS7621F REFRIGERATOR-FREEZER RS7621W & RS7621W WINE CABINET RS6121V INSTALLATION GUIDE NZ AU UK IE EU SG HK
CONTENTS 4 Appliance preparation Integrated refrigerator & freezer 5 Door panel preparation — Stainless steel panel 33 Integrated refrigerator-freezer 6 Door panel preparation — Custom panel 34 Integrated wine cabinet 6 Door panel preparation — Wine cabinet only 35 Safety and warnings 31 Supplied parts 7 Power and water supply connection 37 Required parts 8 Water filter installation 38 Door panel kit 9 Single installation — Align appliance into cabinetry 39 Single installation —
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electrical shock or death. • Read and follow the safety and warnings outlined in this User guide before operating this appliance. READ AND SAVE THIS GUIDE WARNING! To avoid hazard, follow these instructions carefully before Installing or using this appliance. Please make this information available to the persons installing the appliance. z Assume all electrical parts are live.
SAFETY AND WARNINGS INTEGRATED REFRIGERATOR & FREEZER INSTALLATION z z z z z z z z The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 100kg load. Ensure that the anti-tip bracket is installed correctly to prevent the possibility of the appliance tipping forward when the door is open. Ensure the door of the appliance is closed when rolling into the cabinetry.
INTEGRATED REFRIGERATOR-FREEZER INTEGRATED WINE CABINET Refrigerator-Freezer, 61cm Wine Cabinet, 61cm RS6121WLU1, RS6121WLUK1, RS6121WRU1 & RS6121WRUK1 RS6121V2LK1 & RS6121V2RK1 Refrigerator-Freezer, 76cm RS7621WLU1, RS7621WLUK1, RS7621WRU1 & RS7621WRUK1 6 Left or Right hinged door available for each model.
SUPPLIED PARTS INSTALLATION KIT (INTERNAL BOX) TRIMS INSTALL KIT (EXTERNAL BOX) Door panel attachment kit Refrigerator or Freezer #8 x 16 Mush Washer Twin Thread Philips Screw Side bracket (6x) Bracket slider (6x) Side spacer bracket (6x) Anti-tip bracket assembly M5x12 Cross-head screw (35x) #8 x 16 Mush Washer Twin Thread Philips Screw Cabinet side trim (2x) Door panel side cover (2x) Wine Cabinet #10x40 Pan Head Philips Screw Anti-tip bracket (1x) Masonry plug (5x) 10-12x35mm #10x40 cros
SUPPLIED PARTS REQUIRED PARTS MISCELLANEOUS ITEMS (MI) PACK STAINLESS STEEL TOE KICK PANEL Not supplied and can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information. INTEGRATED INTEGRATED COLUMN REFRIGERATOR & FREEZER RS4621F, RS6121F & RS7621F Standard toe kick height is 102mm for standard stainless steel door panel.
DOOR PANEL KIT REFRIGERATOR OR FREEZER REFRIGERATOR-FREEZER Stainless steel door panel kit WINE CABINET Stainless steel door panel kit RH LH Stainless steel door panel kit RH LH RS46 RD4621R4D RD4621L4D RS61 RD6121WRD RD6121WLD RS61 RD6121R4D RD6121L4D RS76 RD7621WRD RD7621WLD RS76 RD7621R4D RD7621L4D RD6121VR4 LH RD6121VL4 M5 x 14 Mush Head SS Philips Screw Custom door panel RS61 M5 x 14 Mush Head SS Philips Screw M5 x 14 Mush Head SS Philips Screw M5 x 14 Mush Head SS Phili
HANDLE KIT CONTEMPORARY PROFESSIONAL Aluminium/Black square handle set Stainless steel square handle set MODEL AHV2-RD84 RS61 REFRIGERATOR-FREEZER AHD3-RD6121W RS61 REFRIGERATOR-FREEZER AHV2-RD6121W RS76 REFRIGERATOR-FREEZER AHD3-RD7621W RS76 REFRIGERATOR-FREEZER AHV2-RD7621W M5x25 Hex screw (4x) DESCRIPTION MODEL AHD5RD6121W RS61 REFRIGERATOR-FREEZER AHC-RD6121W RS76 REFRIGERATOR-FREEZER AHD5RD7621W RS76 REFRIGERATOR-FREEZER AHC-RD7621W M5 x 25 Pan Head Socket Screw RS61 REFRIGERAT
HINGE CHANGE KIT WINE DISPLAY ACCESSORIES Not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information. Select among the hinge change kit options below: HINGE KIT REFRIGERATOR OR FREEZER WINE CABINET Accessories are not supplied with the appliance. A wine display kit and a label kit are sold separately and can be purchased online at fisherpaykel.com.
TOOLS Required tools Supplied tools Not supplied and must be provided by the installer.
PRODUCT DIMENSIONS REFRIGERATOR OR FREEZER B REFRIGERATOR-FREEZER B C A WINE CABINET A C B C A G F D D FRONT E E E PROFILE FRONT PROFILE D FRONT PROFILE 46CM 61CM 76CM MM MM MM A Overall height 2134 2134 2134 B Overall width 451 603 756 C Overall depth (excluding door panel) 610 610 610 73 – 102 73 – 102 73 – 102 E Height from floor to bottom of Stainless steel door/drawer panel 102 102 102 F Height from floor to top of drawer panel (Refrigerator-Freezer only)
CABINETRY DIMENSIONS — SINGLE INSTALLATION D C Flush with front of cabinetry A PLAN E E D B UNFRAMED Aligns appliance with cabinetry D FRAMED Aligns appliance with frame of cabinetry ISOMETRIC 46CM 61CM 76CM MM MM MM A Overall height of cavity 2134 2134 2134 B Overall width of cavity 457 610 762 C Minimum overall depth of cavity* 635 635 635 3 3 3 102 102 102 CAVITY DIMENSIONS d Minimum gap from edge of door panel to cabinetry e Minimum required finished return * Assume
CABINETRY DIMENSIONS — MULTIPLE INSTALLATION DUAL INSTALL TRIPLE INSTALL C C A A B B DUAL INSTALL CAVITY DIMENSIONS 107CM 122CM 137CM 152CM MM MM MM MM A Overall height of cavity 2134 2134 2134 2134 B Overall width of cavity 1067 1220 1372 1524 635 635 635 635 168CM 183CM 198CM 213CM 229CM MM MM MM MM MM A Overall height of cavity 2134 2134 2134 2134 2134 B Overall width of cavity 1677 1829 1982 2134 2286 635 635 635 635 635 C Minimum overall depth o
STAINLESS STEEL DOOR PANEL DIMENSIONS — SINGLE INSTALLATION REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR-FREEZER A A A B B B C C C D 46CM 61CM 76CM MM MM MM A Height of door panel 2029 2029 2029 C Width of door panel 451 603 756 19 19 19 DOOR PANEL DIMENSIONS C Depth of door panel* * Excluding handle 61CM 76CM DOOR PANEL DIMENSIONS MM MM A Height of top door panel 1254 1254 B Height of bottom drawer panel 772 772 C Width of door panel 603 756 19 19 61CM 76
CUSTOM DOOR PANEL DIMENSIONS — SINGLE INSTALLATION REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR-FREEZER A A A B B B C C C D 46CM 61CM 76CM MM MM MM A Height of door panel 1978 - 2080 1978 - 2080 1978 - 2080 C Width of door panel 451 603 756 min 16 - max 25 min 16 - max 25 min 16 - max 25 46CM 61CM 76CM KG KG KG max 20 max 25 max 30 — max 25 — DOOR PANEL DIMENSIONS C Depth of door panel* * Excluding handle DOOR PANEL WEIGHT Weight of Refrigerator or Freezer doo
CUSTOM DOOR PANEL DIMENSIONS — MULTIPLE INSTALLATION DUAL INSTALL TRIPLE INSTALL The illustrations below are examples of custom door panels of different combinations for dual installation. Minimum gaps of 3mm must be retained between door panel side edges and cabinetry regardless of door panel widths. C C The illustrations below are examples of custom door panels of different combinations for triple installation.
TOE KICK DIMENSIONS Custom toe kick options 73mm – 102mm toe kick clearance measured from rear of door panel A A 102mm toe kick height A B B B SINGLE INSTALL SINGLE INSTALL DUAL INSTALL TRIPLE INSTALL 51mm toe kick height (with extra lower grille attached) 152mm toe kick height 46CM 61CM 76CM STAINLESS STEEL/CUSTOM PANEL MM MM MM A Height of toe kick* 102 102 102 B Width of toe kick 454 606 759 92CM 107CM 122CM 137CM 152CM MM MM MM MM MM 50 - 152 50 - 152 50 - 152 50
INSTALLATION OPTIONS SINGLE INSTALL WALL MULTIPLE INSTALL WALL WALL WALL WALL WALL WALL WALL WALL WALL 100mm WALL WALL WALL WALL 60mm WALL WALL WALL WALL The illustrations above show acceptable installation options with reference to the door opening range and partition (optional). Be aware of clashing (circled) of doors or handles when opening at the same time.
DOOR CLEARANCE DRAWER CLEARANCE These dimensions apply to Refrigerator-Freezer models only. C B A A Wall LIMITED INTERNAL ACCESS FULL INTERNAL ACCESS B A Insert hinge limiting pin Before pushing the appliance into the cabinetry, insert the supplied hinge limiting pin into the borehole of the top and bottom door hinges. The hinge limiting pin limits door swing to 90°. For Refrigerator-Freezer models, the hinge limiting pins are inserted into the boreholes of the top and bottom hinges of top door.
ELECTRICAL AND PLUMBING Electrical connection must be within this space if located behind the appliance and must not protrude from the back wall.
CUSTOM DOOR PANEL INSTALL DIMENSIONS Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation, download the folder from http://thekitchentools.fisherpaykel.com. The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. 51mm 50mm Ø2mm REF 18x Pilot holes recommended for bracket attachment. (Do not penetrate front surface).
CUSTOM DOOR PANEL INSTALL DIMENSIONS Ø2mm REF 22x Pilot holes recommended for bracket attachment. (Do not penetrate front surface). Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets. 20mm 90mm 50mm 508mm 1778mm 1978 – 2080mm 20mm) 90mm) Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets. 1270mm 22x Pilot holes recommended for bracket attachment.
CUSTOM DOOR PANEL INSTALL DIMENSIONS For Wine cabinet, the Custom door panel must leave the glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of this appliance. 127mm 302mm 203mm 50mm 50mm 200mm Ø2mm REF 22x Pilot holes recommended for bracket attachment. (Do not penetrate front surface). Do not place pilot holes for handle attachment in marked areas to avoid clashing with panel attachment brackets.
CUSTOM DOOR PANEL INSTALL DIMENSIONS Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. z The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. 301.6mm 127mm 203.2mm 50.8mm 507.8mm 50mm Ø 2mm REF 10x Pilot holes recommended for bracket attachment. (Do not penetrate front surface). 50mm 32.
CUSTOM DOOR PANEL INSTALL DIMENSIONS Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. 377.8mm 50mm 50.8mm 377.8mm 50.8mm 508.4mm 558.4mm 771.5mm 90mm 38.1mm 88.1mm 203.
BEFORE INSTALLATION Checking your cabinetry Check the dimensions of the cabinetry: height, width, depth, floor level, finished alcove returns. Refer to 'Cavity Dimensions' for the correct measurements. Check the power supply and water connections z z z z z z z Ensure that there is a separate power socket for each appliance. Avoid sharing the power point with other appliances to prevent accidental switching off of the appliance. For power requirements, refer to the information on the serial plate.
BEFORE INSTALLATION Removing pre-installed parts Moving your appliance Top trim Be careful when tilting the appliance forward/backward. Tape the door shut to prevent opening while moving the appliance. You need at least two persons to move this appliance. Disengage one end of the top trim from dual lock strips on the non-hinge side of the appliance. Slide the top trim out from the hinge pocket of the appliance. Top door extrusion Remove the brackets from the non-hinge side of the pallet.
CAVITY PREPARATION Anti-tip bracket assembly kit Attaching the anti-tip bracket For solid wall installation back wall 4 Anti-tip bracket (1x) Masonry plug (4x) overhead cabinetry Drill holes suitable to the size of the masonry plugs. Hammer 10x30mm masonry plugs into wall until flush. Fix bracket to wall with #10x40mm cross head screws, and screw tightly. Measure the height (A) of the attachment location from the floor to the alcove return.
APPLIANCE PREPARATION Tools Removing the hanging brackets M8 hex key M8 washer M8 nut Loosen the M8 screws by 1/8" (3mm). 3 13mm spanner 13mm socket wrench 1 Remove the M8 nut and M8 washer from the M8 screw at the top of the door using the supplied hex key and spanner. M8 screw 1/8" (3mm). For Refrigerator-Freezer: 2 Illustrations may differ from your purchased appliance. Remove the hanging bracket and set aside to use later. 4 Repeat steps 1 - 3 to remove the bracket of the drawer.
APPLIANCE PREPARATION Install fasteners kit Attaching the barbed plugs Before rolling into the cavity, insert a barbed plug into the large holes at the top right and left sides of the appliance. Barbed plugs (2x) Cabinet depth alignment gauge (4x) The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance. Tools Cross-head screwdriver Attaching the depth alignment gauges Loosen the right and left screws at the top and bottom sides of the door.
DOOR PANEL PREPARATION — STAINLESS STEEL PANEL Door handle kit M5 x 25 M5x25 Hex screw (4x) Attaching the handle Attaching the brackets Remove the protective film around the handle attachment area before installing the handle. Protect the finish of the door panel to avoid damage or scratches to the surface. hanging bracket Door panel attachment kit side bracket For Refrigerator/Freezer/Wine cabinet Secure the top hanging bracket to the screw holes of the door panel with 8Gx16 Mush washer screws.
DOOR PANEL PREPARATION — CUSTOM PANEL Door handle kit Attaching the handle Attaching the brackets Refer to 'Custom door panel installation dimensions' page for correct screw hole positions on the door panel. Refer to 'Custom door panel installation dimensions' page for correct screw hole positions on the door panel. M5 x 25 marked line M5x25 hex screw (4x) top hanging bracket side bracket Door panel attachment kit For all models Mark a line across the centre of the custom door panel.
DOOR PANEL PREPARATION — WINE CABINET ONLY Installation kit Attaching the long glass trims Glass trims are attached to cover the gap between the Stainless steel door panel and glass panel. hanging bracket Do not exceed pass this line Long trim (2x) long trim long trim Attach the peeled portion of the trim starting from the top of the flange on one side of the door panel cutout. Tools z red protective film Ensure the trim does not overlap the hanging bracket.
DOOR PANEL PREPARATION — WINE CABINET ONLY Installation kit Short trim (2x) Attaching the short glass trims 1 short trim Place the short trim along the length of the top of door panel cutout across the top ends of the long trims. (A) 3 short trim Attach the peeled portion starting from one end of flange perpendicular to top end of long trim. Tools long trim Cutter Cut both ends of the short trim to length. 2 Peel off a small portion of red protective film from the short edge.
POWER AND WATER SUPPLY CONNECTION Water fittings kit Connecting to water supply Ensure the door of the appliance is closed before rolling into the cabinetry. Push the appliance carefully towards the front of the cabinetry close enough to allow access at the back for power and water connection. Ensure an isolating tap is available if water supply is not easily accessible.
WATER FILTER INSTALLATION Freezer and Refrigerator with Ice & Water function Refrigerator-Freezer Keep the door closed and ensure the appliance is stable before installing the water filter to avoid risk of appliance tipping over. Keep the door closed and ensure the appliance is stable before installing the water filter to avoid risk of appliance tipping over. 1 Remove the packaging of the supplied water filter. 1 Pull the filter tool gently to dislodge from the front of the appliance.
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY Tools Pushing into the cabinetry Cross-head screwdriver 7 1/16" (180mm) Roll the appliance carefully into the cabinetry until the anti-tip bracket overlaps the back edge of the appliance. z z Ruler Ensure the bracket overlaps the appliance by a minimum 7 1/16" (180mm) for a secure hold. Be careful not to run over the water hose and power cord when rolling in the appliance.
SINGLE INSTALLATION — ALIGN APPLIANCE INTO CABINETRY Tools Adjusting the alignment in the cabinetry Cross-head screwdriver Powered driver (optional) 1 Front foot adjustment screw Clockwise turn of the front and rear adjustment screws raise the height of the appliance. Rear foot adjustment screw Counter-clockwise turn of the adjustment screws lower the height of the appliance.
SINGLE INSTALLATION — SECURE APPLIANCE INTO CABINETRY Install fasteners kit Securing the top brackets 8Gx16 Countersunk screw (6x) Fix the top brackets to the ceiling surface of the cabinetry with 8Gx16 countersunk screws. Tools Cross-head screwdriver Powered driver (optional) Securing the side brackets Fix the side brackets (2x) to the lower right and left sides of the cabinetry with 8Gx16 countersunk screws.
DOOR PANEL INSTALLATION Tools Hanging the door panel Cross-head screwdriver M4 hex key (1x) 1/2" (13mm) spanner (1x) 1 Hold the door panel at an angle from the top of the door and lower the screw holes of the hanging bracket onto the adjustment screws. . 3 Screw the M8 washer and nut to the adjustment screw and loosely tighten. 1/2" (13mm) socket wrench For Refrigerator-Freezer Repeat steps 1 - 3 for the top door and drawer panels.
DOOR PANEL INSTALLATION Tools Adjusting the height of door the panel Re-adjusing the door panel Ensure the side brackets are loosely screwed when adjusting the height of the door panel. Do not adjust the door panel height when the side brackets are screwed tight. This can generate friction which causes the hanging brackets to bend. Cross-head screwdriver Turn the adjustment screw to raise or lower the height of the door panel relative to the door.
DOOR PANEL INSTALLATION Tools Installing locking bracket TOE KICK INSTALLATION Adjusting mounting plate brackets Cross-head screwdriver Cutter M4 hex key (1x) REFRIGERATOR OR FREEZER / WINE CABINET REFRIGERATOR—FREEZER Loosen the screw at the bottom of the door, and slide the locking bracket out until it touches the panel. 13mm spanner (1x) 1 Refrigerator-Freezer The locking bracket is located at the bottom of the top door panel.
TOE KICK INSTALLATION Miscellaneous components Attaching the mounting plate mounting plate Re-attach the toe kick mounting plate to the plinth using same screws that were set aside previously. Air toe kick seal (1x) Toe kick install kit 1 air toe kick seal If toe kick depth is less than 3 5/8" (92mm), attach an air toe kick seal to the mounting plate. Peel off the adhesive tape of air toe kick seal and attach to the middle of the back side of the mounting plate.
GRILLES INSTALLATION Tools Attaching the top grille Refrigerator or Freezer/ Wine Cabinet Cutter Open the door, and secure both ends of the grille and behind the water filter hatch with #8x16 screws. Refrigerator-Freezer Reattach the top grille with #8x16 screws. top grille top grille Cross-head screwdriver Attaching the bottom grille Refrigerator or Freezer/ Wine Cabinet Re-attach the bottom grille via magnets. Refrigerator-Freezer Re-attach the bottom grille via magnets.
CARBON FILTER INSTALLATION The carbon filter is used for Wine Cabinet models only, Ensure the cover is completely closed to prevent hatch or filter from being damaged. Replacement filters (862755) can be purchased online from fisherpaykel.com or by calling Fisher & Paykel Customer Care. 1 AIR FLOW DIVIDER INSTALLATION The air flow divider blocks the air flow from bypassing the front of the bottom grille. Remove the packaging of the filter.
CABINET TRIMS INSTALLATION Trims install kit Installing cabinet side trims door hinge adhesive strip Dual adhesive strips are pre-attached at four locations along the side trims. z 1 Cabinet side trim (2x) trim Ensure the adhesive strips are pressed firmly to the cabinet side trims. Peel off the liners from the dual adhesive strips. z Position the trim at an angle on the throat of the door hinge. Ensure the adhesive surface is clean and free of dust or small particles.
DOOR COVERS & TRIMS INSTALLATION Trims install kit Re-installing the top cover (for all models) Remove the backing film of dual adhesive strips pre-attached to the top of the door. Ensure the magnet is in place before installing the top cover. trim cap top cover notch Top door panel side extrusion (2x) Align the top cover to the top of the door. 1 magnet housing trim cap Clip the notch into the magnet housing, and the trim caps on top of the adhesive strips.
TOP TRIM & HINGE POCKET COVERS INSTALLATION installing the top trim (for all models) Slide one end of the top trim into the hinge pocket of the appliance. Press the other end to engage the dual lock strips on the non-hinge side of the appliance. top trim installing the hinge pocket covers (for all models) Follow the steps below to install the covers for the top, bottom or middle hinge pockets.
MULTIPLE INSTALLATION — APPLIANCE PREPARATION Install fasteners kit Attaching the central spacer to cabinetry Attach barbed plugs and depth alignment gauges barbed plugs Barbed plugs (2) depth gauges locations A Before rolling into the cavity, insert the barbed plugs into large holes on the top right and left sides of both appliances. b Cabinet depth alignment gauges (4) 1 The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance.
MULTIPLE INSTALLATION — ALIGN FIRST APPLIANCE INTO CABINETRY Tools Pushing first appliance into the cabinetry min 7 1/16" (180mm) Ruler Roll the first appliance slowly into one side of the cabinetry until the anti-tip bracket overlaps the back edge of the appliance. 1 first appliance anti-tip bracket Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold. Refer to 'Attach the anti-tip bracket' for more information.
MULTIPLE INSTALLATION — SECURE FIRST APPLIANCE INTO CABINETRY Install fasteners kit Adjusting alignment of first appliance in cabinetry 8Gx16 Countersunk screw (6) 1 Rear foot adjustment screw Front foot adjustment screw Tools Securing the top brackets Turn the front and rear adjustment screws clockwise to raise height of the appliance and counter-clockwise to lower the height.
MULTIPLE INSTALLATION — ALIGN SECOND APPLIANCE INTO CABINETRY Tools Pushing into the cabinetry Push the second appliance to roll slowly into the other side of the cabinetry side by side with the first appliance. min 7 1/16" (180mm) Ruler 1 Ensure the bracket overlaps the appliance by a minimum 7 1/16" (180mm) for a secure hold. Refer to 'Install antitip bracket' for more information.
43453 M6 Washer M5 Washer MULTIPLE INSTALLATION — SECURE SECOND APPLIANCE INTO CABINETRY M5 x20 Cap Screw 248072 M6 x 12 Cap Screw 840371 8Gx16 Mush Washer M5x20 Cap screw (1) 847984 Top joiner fastener kit Securing the top brackets cap screw washer M5x16x1 Plain washer (1) 10 x 50 Dual Lock Bottom joiner fastener kit Secure the top caps of both appliances to the central spacer with M5x20 cap screw and washer.
MULTIPLE INSTALLATION — INSTALL CABINET TRIMS Tools Install the centre trim Aluminium centre trim (1x) Dual adhesive strips (4x) 1 2 Four dual adhesive strips are pre-attached along the centre trim. Peel off the liners from the dual adhesive strips. Position the trim between the throats of both appliances. Push and press the trim on the appliances/throat. Make sure the top end of the trim is pushed up against the cavity ceiling before fixing the position.
WINE DISPLAY FOR WINE CABINET Handle assembly Cradle assembly Retainer blocks are pre-assembled at the bottom of both ends of the handle. A retainer block is pre-assembled at the bottom of each cradle. Use a spacer to correctly position the cradle and avoid wine bottles being too upright resulting in bottles tipping over. 1 Loosen the screws until the retainer blocks can be inserted between slats of display rack. 2 Align handle to the front end of display rack.
CHANGE THE DOOR HINGES (OPTIONAL) You have the option to switch the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation, and must be purchased separately. Ensure that you remove all the shelves, covers and trims from the appliance before changing the hinges. Take care not to damage the door.
CHANGE THE DOOR HINGES (OPTIONAL) Detach the top door hinge A b C E D f Detach the bottom door hinge — For Refrigerator & Freezer / Wine Cabinet a B d C E F E Do not remove! 1 Rotate the bottom hinge (A) outwards and remove bottom hinge pocket cover (B) using a flat head screwdriver in the slot. 2 Remove the hinge by unscrewing the M6x16 countersunk screws (2x) (C). 3 Open the water filter hatch on the bottom grille and unscrew the #8x16 screw (D) while holding the grille in place.
CHANGE THE DOOR HINGES (OPTIONAL) Move the sensor housing 1 Unclip the hall sensor from the housing. 4 Move the sensor housing to align the opposite hall sensor clip with the centre of the cabinet. Reinstall the sensor housing using #8x16 screws (2x) into the pre-drilled holes in the cabinet top panel. 5 Clip the hall sensor into 2 Unhook the interceptor board harness from sensor housing so harness is loose. 6 3 Remove the #8x16 screws (2x) from the sensor housing.
CHANGE THE DOOR HINGES (OPTIONAL) Re-attach the top door hinge D e c A b f Re-attach the bottom door hinge — Refrigerator or Freezer / Wine Cabinet 1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk screws (A) on the new hinge side at the other side of the appliance. 2 Install the new hinge pocket and alcove top bracket on the new hinge side using two (2x) M6x16 countersunk screws (B). z The new hinge pocket and top alcove bracket are supplied with the hinge kit.
CHANGE THE DOOR HINGES (OPTIONAL) Change the top door brackets Reinstall the door L A FIL L FIL M6x10 hex screws Top hinge ILL NO F NO F NO NO 1 Unscrew the M5x10 screws (4x) to remove the top adapter bracket from the top of the door (A). 2 Install the new top adapter bracket into the other side of the top of the door with M5x10 screws (4x) (B). ILL L FIL L FIL L IL OF N IF LL 1 Secure the door to the top hinge and bottom/middle hinge with M6x10 hex screws (4x).
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER ALL MODELS F Cabinet Level: Ensure the appliance is level and dimensions accurate. Refer to 'Cabinetry Dimensions, pages 16-17'. F Packaging: Ensure all internal and external packaging has been removed. Refer to 'Before installation', page 27. F Anti-tip: Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Refer to 'Cavity preparation, page 29' F Fault codes: Ensure no error codes are shown.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2020. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
