INTEGRATED COLUMNS WINE CABINET RS6121VL2K1 & RS6121VR2K1 models INSTALLATION GUIDE NZ AU GB IE SG HK 863021A 11.
CONTENTS SAFETY AND WARNINGS 4 INSTALL DOOR PANEL INTEGRATED COLUMNS — WINE CABINET 5 Hanging door panel 33 COMPONENTS 6 Adjusting door panel 34 DOOR PANEL AND HANDLE SETS 8 WINE DISPLAY ACCESSORIES 9 Adjusting toe kick grille TOOLS 9 Installing toe kick mounting plate APPLIANCE DIMENSIONS 10 INSTALL TOE KICK MOUNTING PLATE INSTALL TOE KICK AND GRILLES 33 35 35 35 36 CAVITY DIMENSIONS 11 Installing toe kick 36 DOOR PANEL DIMENSIONS 13 Attaching top and bottom grilles 36 TOE
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Read and follow the safety and warnings outlined in this installation guide before operating this appliance. Failure to do so can result in death, electric shock, fire or injury to persons. ! WARNING! Cut Hazard Take care — panel edges are sharp. Failure to use caution could result in injury or cuts.
SAFETY AND WARNINGS INTEGRATED COLUMNS — WINE CABINET INSTALLATION Cavity preparation zz zz The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 225lb/100kg load. Ensure that the anti-tip bracket is installed correctly to prevent the possibility of the appliance tipping forward when the door is open. Positioning inside the cabinetry zz zz zz DO NOT attempt to open the door until the appliance is fully installed.
COMPONENTS Installation kit (Internal box) Supplied with appliance Miscellaneous components Door panel attachment kit Side bracket (6) Bracket slider (6) Side spacer bracket (6) For Custom door panels: M5x12 Cross-head screw (30) Anti-tip bracket assembly kit Flow divider cap (1) Locking clip (2) Install fasteners kit 10-12x35mm cross-head screw (5) Depth alignment gauge (4) Barbed plug (2) #8 x 19 Countersunk Twin Thread Posi Screw #8 x 19 Countersunk Twin Thread Posi Screw Masonry plug (4)
COMPONENTS Miscellaneous items (MI) pack Hinge change kit (Optional) Supplied with appliance Not supplied and must be purchased separately INTEGRATED COLUMNS INTEGRATED COLUMN WINE CABINET WINE CABINET RS2484VL2K1, RS2484VR2K1, RS2484VL2K1, RS2484VR2K1, RS6121VL2K1, RS6121VR2K1 RS6121VL2K1, RS6121VR2K1 models models SERVICE & WARRANTY SERVICE ET GARANTIE ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ SERVIZIO E GARANZIA SERVICE & GARANTIE HUOLTO JA TAKUU USER GUIDE US CA NZ AU GB IE SG HK 863023A SERVICE OG GARANTI IN
DOOR PANEL AND HANDLE SETS Door panel set Not supplied and must be purchased separately Stainless steel door panel set: Custom door panel set: (Fisher & Paykel) Supplied by customers to match their cabinetry. Custom Door Panel must leave glass pane visible. A full custom panel sheathing over the glass pane does not meet the specifications of this appliance. Door handle set Not supplied and must be purchased separately.
WINE DISPLAY ACCESSORIES IMPORTANT! TOOLS Required tools Wine display accessories are not supplied with the appliance. A wine display kit and a label kit are sold separately and can be purchased online at fisherpaykel.com.
APPLIANCE DIMENSIONS C A B PRODUCT DIMENSIONS A Overall height of product 2134 B Overall width of product 603 C Overall depth of product (excluding front door panel) 610 Weight (including packaging) 10 MM 172kg
CAVITY DIMENSIONS C A B CAVITY DIMENSIONS MM A Overall height of cavity 2134 b Overall width of cavity c Overall depth* (including door panel) if power plug is located in adjacent cabinet 635 Overall depth* (including door panel) if power plug is located behind appliance 650 24” 610 * Cavity depth assumes door panel thickness of 19mm.
CAVITY DIMENSIONS Frameless Cabinetry Framed Cabinetry Aligns appliance flush with the cabinetry Aligns appliance flush with the frame of cabinetry A A B CAVITY DIMENSIONS 12 A Minimum required finished return (cavity sides and top) b Minimum cabinetry gap clearance from edge of door panels B MM 102 3
DOOR PANEL DIMENSIONS STAINLESS STEEL/CUSTOM DOOR PANEL DOOR PANEL DIMENSIONS (STAINLESS STEEL) MM A Height of door panel 2029 B Width of door panel 603 C Depth of door panel (excluding door handle) 3/4" (19) DOOR PANEL DIMENSIONS (CUSTOM)* A Height of door panel 1978 – 2080 B Width of door panel 603 C Depth of door panel 16 – 25 DOOR PANEL WEIGHT Maximum weight of Stainless steel/Custom door panel (including handle/brackets)† LB (KG) 55lb (25kg) †D oor handle kit is available as an
TOE KICK PANEL DIMENSIONS TOE KICK DIMENSIONS A MM Width of toe kick Stainless steel panel/Custom panel B 607 Height of toe kick# Stainless steel panel 102 Custom panel** C 50 – 152 Depth of toe kick (measured from front of door) Stainless steel panel/Custom panel 73 –102 Standard toe kick height is 4" (102mm) with the optional Stainless door panel. For Custom door panel installation, a custom toe kick 2 – 6" (50 – 152mm) can be manufactured and fitted by cabinetmaker.
CUSTOM DOOR PANEL DIMENSIONS Custom door panel dimensions 302mm 203mm 127mm Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com.
DOOR CLEARANCE IMPORTANT! IMPORTANT! Ensure the appliance is stable before opening the door. zz zz Ensure the hinge limiting pin is inserted before pushing the appliance into the cabinetry. The pin fits in the boreholes of the top hinge. C B AE A Insert hinge limiting pin (supplied) to limit door swing to 90°.
ELECTRICAL DIMENSIONS WARNING! zz zz Electric shock hazard! Assume all parts live. Disconnect power supply before servicing and installation. ELECTRICAL AND PLUMBING CONNECTIONS 1 Recommended location for connections in adjacent area or unit 2 Alternative location for connections at rear of cavity C C REAR OF CAVITY A D 1 Floor Electrical connection must be within this space if located behind the appliance and must not protrude from the back wall.
ELECTRICAL SPECIFICATIONS B A Power cord (excluding plug) MAXIMUM DISTANCE OF POWER CORD AND WATER HOSE Power cord (excluding plug) MM ELECTRICAL SPECIFICATIONS a Power cord length from left side edge of appliance (excluding plug) 1309 Supply 230 VAC, 50 Hz b Power cord length from right side edge of appliance (excluding plug) 1335 Service 10 amp circuit Socket 3-pin earthing-type Power cord (total length) 2000mm 18
BEFORE INSTALLATION Check your appliance IMPORTANT! zz zz zz Top door panel extrusion Ensure that your appliance is the correct model as per your order. Check that the components and install kits are complete. Keep the detached parts to reinstall later.
BEFORE INSTALLATION Check the installation location Check the cabinetry zz Check the dimensions of the cabinetry: height, width, depth, floor level, finished alcove returns. Check the power supply connection zz zz zz zz zz zz zz 20 Ensure that there is a separate power socket for each appliance. Avoid sharing the power point with other appliances to prevent accidental switching off of the appliance. For power requirements, refer to the information on the serial plate.
INSTALL ANTI-TIP BRACKET Anti-tip bracket assembly kit 1 Measure height from floor to alcove return (A). Use this measurement to locate the attachment height (B) of anti-tip bracket to the back wall. zz 2 Mark a horizontal line on the back wall based on measured attachment height. Ensure there is a stud behind the wall. Attachment height of anti-tip bracket should not be more than 2138mm to ensure the appliance is prevented from tipping over during installation. 3 Place the bracket to the backwall.
CONNECT TO POWER SUPPLY 1 Move appliance in front of cabinetry close enough to allow access at the back for power connection. Rear view of appliance 2 22 Uncoil the power cord from the clips .
ATTACH DEPTH ALIGNMENT GAUGES Install fasteners kit IMPORTANT! The alignment gauges are only temporary and must be removed after installation. Cabinet depth alignment gauge (4) Tools Left Cross-head screwdriver right and left screws at top and 1 Loosen bottom sides of door. 3 Attach alignment gauge so that screw head passes through the keyhole. 2 Locate alignment gauges to screws at correct orientation.
POSITION APPLIANCE INSIDE THE CABINETRY Install fasteners kit Attach barbed plugs IMPORTANT! zz Barbed plug (2) zz Check clearance between floor and feet. Rollers must roll freely on the floor. Be careful not to run over the power cord when rolling in the appliance. Barbed plug 1 Before rolling into the cavity, insert barbed plugs into large holes on the top right and left sides of the appliance.
ALIGN APPLIANCE INSIDE THE CABINETRY Tools Align depth gauges with cabinetry Cross-head screwdriver Ruler Left 1 Mark the step of depth gauge on each side of the door based on the thickness of door panel. adjacent cabinetry 2 Right adjacent cabinetry Move the appliance to align the marked steps of gauges to be flush with front surface of adjacent cabinetry. Use a ruler to check if gauges are in line relative to thickness of door panel.
ALIGN APPLIANCE INSIDE THE CABINETRY Tools Adjusting appliance inside the cabinetry IMPORTANT! zz zz zz Turn front and rear adjustment screws clockwise to raise height of appliance and counter-clockwise to lower height. One turn of adjustment screw is equal to 0.5mm height adjustment. Use a cross-head screwdriver to turn the screws. If using a powered driver, use low torque setting.
FIX APPLIANCE INSIDE THE CABINETRY Install fasteners kit IMPORTANT! zz zz Remove the alignment gauges before fixing the appliance to the cabinetry. Ensure the appliance does not move as you open the door when you tighten the screws. 8Gx16 Countersunk screw (6) Tools 1 Open the door and remove depth gauges from both sides of appliance. 3 Close the door and fix top brackets (2x) to ceiling surface of cabinetry with 8Gx16 countersunk screws (2x).
INSTALL CARBON FILTER MI pack Housing Push-open latch Carbon filter (2) 1 Remove filter from packaging. Cover 2 Open the cover of filter housing by pushing the latch. Hatch Filter housing 3 Insert carbon filter in hatch. 4 Push the filter gently into the hatch until flush, and then close the cover until it locks to the latch. Filter housing IMPORTANT! zz zz 28 Ensure the cover is completely closed to prevent hatch or filter from being damaged.
PREPARE FOR DOOR PANEL INSTALLATION Tools Removing hanging bracket M4 hex key (1) 13mm spanner (1) M8 nut M8 washer adjustment screw 1 Remove the M8 washer and M8 nut from the adjustment screw at the top the door. 3mm 2 Remove hanging bracket and set aside to use later. 3 Loosen the adjustment screw by 3mm.
PREPARE FOR DOOR PANEL INSTALLATION Door handle kit IMPORTANT! zz M5 x 25 zz M5x25 Hex screw (4x) Door panel attachment kit zz A stainless steel door panel has pre-drilled screw holes for attaching door handle and brackets. For custom door panels, see 'Custom door panel dimensions' (page 15) for correct screw hole locations of handles and brackets. Remove the protective film around the handle attachment area of the stainless steel panel before installing the handle.
ATTACH DOOR PANEL GLASS TRIM Installation kit IMPORTANT! Attaching long glass trims zz hanging bracket Glass trims are attached to cover the gap between the door panel and the glass panel. long trim A long trim Long trim (2) red protective film Tools 1 Peel off a small portion of red protective film from one end of long trim. (A) 3 Continue attaching the long trim for the length of the door panel cutout, peeling off the film as you go.
ATTACH DOOR PANEL GLASS TRIM Installation kit Attaching short glass trims 1 short trim 4 Place the short trim along the length of the top of door panel cutout to determine the correct length between long trims. (A) C A Attach the peeled portion starting from one end of flange perpendicular to top end of long trim (D).
INSTALL DOOR PANEL Tools Hanging door panel hanging bracket Cross-head screwdriver M4 hex key (1) 13mm spanner (1) 1 Align door panel to door at an angle. 3 Align door panel straight with the door. 2 Align the holes of the hanging bracket over the adjustment screws and lower the door panel into place. Side brackets 4 Align and slot side brackets of door panel to side screws of door. 5 Loosely screw M8 washer and nut to adjustment screw.
INSTALL DOOR PANEL Tools IMPORTANT! Adjusting door panel Check gaps 1/8" (3mm) between door panel/cabinetry using depth gauge. All door panels have full axis adjustment to ensure flushness with adjacent walls. Cross-head screwdriver Top bracket M4 hex key (1) Lower Raise 3 To adjust door panel further, remove door panel then loosen the fixing screws of hanging bracket and move the bracket sideways to suit.
INSTALL TOE KICK MOUNTING PLATE Toe kick grilles Adjusting toe kick grille Installing toe kick mounting plate Magnet with double-sided tape Top grille (1) Toe kick mounting plate Magnet with double-sided tape Bottom grille (1) 3 Top bracket Tools Reinstall toe kick mounting plate to plinth using same screws set aside previously. NOTE: If toe kick depth is less than 92mm, attach an air toe kick seal to the mounting plate.
INSTALL TOE KICK AND GRILLES Miscellaneous components Installing toe kick Attaching top and bottom grilles Air toe kick seal (1) Toe kick install kit 3 Toe kick (1) 1 Reinstall top grille using same screws set aside previously, and reattach cover to bottom hinge pocket. Peel off the adhesive tape backing of the magnets. Cutter 4 Reinstall the bottom grille to the mounting plate. NOTE: For toe kick heights 114 – 127mm, shorten the bottom grille by cutting along the vertical ribs.
INSTALL CABINET TRIMS Dual install joiner kit Re-installing top trim Re-installing flow divider Twist to prise open Expose adhesive Exploded with machine screw The flow divider blocks the air flow from bypassing in front of the bottom grille. IMPORTANT! hinge side zz A zz B zz For toe kick height greater than 102mm, shorten the air flow divider. Cut along the outline on both the divider and divider cover before installation to the door. Ensure to file the cut portions of the divider and cover.
INSTALL CABINET TRIMS Install parts Installing side trims Four (4) dual-lock strips are pre-installed along each side trim. dual lock strips trim Cabinet side trim assembly (2) door hinge Dual-lock strip (4) Tools 1 Peel off the liners from the dual-lock strips. 2 top hinge Position the trim on the throat at an angle. IMPORTANT! zz Cross-head screwdriver zz Press firmly on the dual-lock strip locations to ensure the side trims are securely attached. Repeat steps 1-4 to the other side trim.
INSTALL DOOR TRIMS Miscellaneous components Installing door trims 1 Position door panel top extrusion to top of door. 2 Align notch with magnet housing. Peel off the liners from the dual-lock strips. Press top extrusion down so that dual lock strips engage each other. Align top of side extrusions to fit with right and left ends of top extrusion. Clip trim caps at both ends of top extrusion.
WINE DISPLAY Installing wine display kit Installing wine label kit Handle assembly Retainer blocks are pre-assembled at the bottom of both ends of the handle. 1 Loosen the screws until the retainer blocks can be inserted between slats of display rack. 2 Align handle to the front end of display rack. 3 Rotate retainer block to lock position and tighten screw to lock handle in place. 7 Write the name or type of wine on the label. 9 Wipe the labels with a damp cloth to erase.
OPTIONAL — CHANGE DOOR HINGES Tools You have the option to change the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation, and must be purchased separately. IMPORTANT! zz We recommend to lay the appliance (door closed) onto its back on the pallet when removing the door hinges. Removing the door T2 star-head screwdriver 1 Release the hinge spring by turning the T2 screw in the hinge to ‘0’ position.
OPTIONAL — CHANGE DOOR HINGES Tools T2 star-head screwdriver Flat-head screwdriver Removing top door hinge 1 Rotate the top hinge (A) outwards and remove the top hinge pocket cover (B) using the flat head screwdriver in the slot of the cover. 2 Unscrew M5x12 pan head screws (C) to remove top hinge, and set aside to use later. 3 Unscrew M5x12 pan head screws (D) from hinge pocket to remove hinge pocket and top alcove bracket.
OPTIONAL — CHANGE DOOR HINGES Tools Moving the sensor housing C T2 star-head screwdriver A B Flat-head screwdriver 1 Unclip the reed switch from the housing (A). the interceptor board harness 2 Unhook from sensor housing so harness the #8x16 screws (2x) from 3 Remove the sensor housing (C). is loose (B). D 4 Move the sensor housing so that the opposite reed switch clip is aligned with the centre of the cabinet (D).
OPTIONAL — CHANGE DOOR HINGES Hinge change assembly Hinge (right or left) top pocket (1) Lower (right or left) hinge bracket (1) Top hinge installation 1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk screws (A) on the new hinge side at the other side of the appliance. 2 Install the new hinge pocket and alcove top bracket on the new hinge side using two (2x) M5x12 pan head screws (B). Note: The new hinge pocket and alcove top bracket are supplied with the hinge kit.
OPTIONAL — CHANGE DOOR HINGES Hinge change assembly K05 top adaptor bracket R/L (1) K05 bottom adaptor bracket R/L (1) Tools Door brackets 1 Remove the top adapter bracket from the top of the door by unscrewing M5x10 screws (4x) (A). 2 Install the new top adapter bracket into the other side of the top of the door with M5x10 screws (4x) (B). 3 Remove the door panel locking bracket and washer from the bottom of the door by unscrewing M6x25 screw (1x) (C).
OPTIONAL — CHANGE DOOR HINGES Tools Door installation 1 T2 star-head screwdriver Flat-head screwdriver the hinge spring by turning the star T20 2 Activate screws to the I position (B). Reinstall the door to the appliance using M6x10 hex screws (4x) into the hinges (A). A B Top hinge A Hex key Bottom hinge 3 46 Return the appliance to the upright position, and reinstall all covers and trims.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the door can open and close freely with no resistance from surrounding cabinetry. Ensure hinge limiting pin is fitted for 90° door swing. Ensure all internal and external packaging is removed from the appliance before use.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The appliance specifications in this document apply to the specific appliances and models described at the date of issue. Under our policy of continuous appliance improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this document correctly describes the appliance currently available. NZ AU GB IE SG HK 863021A 11.
