INTEGRATED COLUMN REFRIGERATOR FREEZER RS6121WR, RS7621WR, RS6121WL & RS7621WL models INSTALLATION GUIDE NZ AU GB IE
CONTENTS Safety and warnings 4 Cavity dimensions — 610MM + 610MM dual install 29 Integrated column models 5 Cavity dimensions — 610MM + 760MM dual install 30 Check your appliance 6 Cavity dimensions — 760MM + 760MM dual install 31 Remove pre-installed parts 6 Toe kick panel dimensions — dual install 32 Moving your appliance 7 Power supply dimensions 33 Supplied parts 8 Electrical specification 34 Required parts 10 Plumbing specification 34 Door panel set 11 Before installation
SAFETY AND WARNINGS ! WARNING! SAVE THESE INSTRUCTIONS WARNING! Electric Shock Hazard Failure to follow this advice may result in electrical shock or death. z • Read and follow the safety and warnings outlined in this User guide before operating this appliance. z To avoid hazard, follow these instructions carefully before installing or using this appliance. Please make this information available to the person installing the appliance. z Assume all electrical parts are live.
SAFETY AND WARNINGS INTEGRATED COLUMN MODELS Positioning inside the cabinetry z z Ensure the door of the appliance is closed when rolling into the cabinetry. Ensure the power cord is not run over or damaged when rolling the product into the cabinetry. Aligning inside the cabinetry z z For flush installation, ensure the door panels are installed flush with cabinetry front surface. Ensure the appliance is properly is centred.
CHECK YOUR APPLIANCE Ensure you follow the unpacking steps printed on the packaging box of your appliance. Check that your appliance is the correct model as per your order. Check that the components and install kits are complete. REMOVE PRE-INSTALLED PARTS B A Remove the trims kit at the back of the appliance.
MOVING YOUR APPLIANCE Follow the steps below to move your appliance to the install location. Be careful when tilting the appliance forward/backward. Tape the door shut to prevent opening while moving the appliance. Remove the brackets from the non-hinge side of the pallet. 1 Restrain the appliance with strap and remove the remaining brackets. 4 Strap Hand truck 2 Tilt the appliance slightly forward and insert the hand truck between pallet and appliance.
SUPPLIED PARTS DOOR PANEL ATTACHMENT KIT INSTALL FASTENERS KIT Bracket slider (6) Side spacer bracket (6) Depth alignment gauge (4) Barbed plug (2) #8 x 19 Countersunk Twin Thread Posi Screw #8 x 19 Countersunk Twin Thread Posi Screw Side bracket (6) 8Gx16 Countersunk screw (7) For Custom door panels: M5x12 Cross-head screw (32) ANTI-TIP BRACKET ASSEMBLY MISCELLANEOUS PARTS Supplied in separate bags 8 Masonry plug (4) #10x40 Pan Head Philips Screw #10x40 Pan Head Philips Screw Anti-tip bra
SUPPLIED PARTS TRIMS INSTALL KIT (EXTERNAL BOX) Top door panel side extrusion (2) WATER FILTER KIT Cabinet side trim (2) Collet locking clip (1) Bottom drawer panel side extrusion (2) Water filter (1) Bottom drawer top trim (1) 1/2 BSP Stainless steel braided hose with adaptor (1) MISCELLANEOUS ITEM PACK 1/4” (6.
839107 M5 Nut 843453 M6 Washer REQUIRED PARTS TOE KICK PANEL INSTALL JOINER KIT M5 Washer Used for dual or multiple installation of appliances. Can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information. Not supplied and can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information. Standard toe kick height is 102mm for standard stainless steel door panel.
DOOR PANEL SET DOOR AND DRAWER HANDLE KITS Not supplied and must be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.com for more information.
HINGE CHANGE KIT Not supplied and must be purchased separately. Available online at fisherpaykel.com.
PRODUCT DIMENSIONS — 610MM MODEL B C PRODUCT DIMENSIONS A MM A Overall height 2134 B Overall width 603 C Overall depth* 610 *Excluding front door panel.
CAVITY DIMENSIONS — 610MM MODEL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the frame of cabinetry. Aligns appliance flush with the cabinetry. A E E C C BD D A A B B CAVITY DIMENSIONS A Overall height 2134 B Overall width 610 C Minimum overall depth* 635 D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return * Assumes a door panel thickness of 3/4” (19mm).
DOOR PANEL DIMENSIONS — 610MM MODEL STAINLESS STEEL PANEL CUSTOM PANEL A A B B C C D DIMENSIONS A Height of top door panel D MM 1254 DIMENSIONS A Height of top door panel MM 1254 B Height of bottom drawer panel 772 B Height of bottom drawer panel 772 C Width of door/drawer panel 603 C Width of door/drawer panel 603 D Depth of door panel* 19 D Depth of door panel* min 16 - max 25 DOOR PANEL WEIGHT KG DOOR PANEL WEIGHT KG Weight of top door panel 9 Weight of top door panel** Wei
CUSTOM DOOR PANEL INSTALL DIMENSIONS — 610MM MODEL Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. z z The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. Measurements of screw hole locations can vary depending on the height of toe kick 50 – 152mm. 301.6mm 203.2mm 38.
DOOR CLEARANCE — 610MM MODEL 115° DOOR OPENING 90° DOOR OPENING C B Insert hinge limiting pin A A WALL Before pushing the appliance into the cabinetry, insert the supplied hinge limiting pin into the borehole of the top hinge. The hinge limiting pin limits the door swing to 90°.
DRAWER CLEARANCE — 610MM MODEL DIMENSIONS B A A Maximum drawer extension when open* 400 B Maximum drawer extension when open** 461 * Excluding handle ** Including handle 18 MM
TOE KICK DIMENSIONS — 610MM MODEL STAINLESS STEEL TOE KICK PANEL CUSTOM PANEL TOE KICK PANEL Can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel. com for more information. For Custom door panel installation, a custom toe kick 2” – 6” (50 – 152mm) can be manufactured and fitted by cabinetmaker. The Custom door panel height needs to be adjusted accordingly. Extra lower grilles are required for a 2” (50mm) toe kick installation.
TOE KICK INSTALL OPTIONS toe kick panel 20 Standard toe kick height is 4" (102mm) with Stainless steel door panel. For custom toe kick with 6" (152mm) height. For custom toe kick with 2" (50mm) height (extra lower grille attached).
PRODUCT DIMENSIONS — 760MM MODEL PRODUCT DIMENSIONS MM A Overall height 2134 B Overall width 756 C Overall depth* 610 *Excluding front door panel.
CAVITY DIMENSIONS — 760MM MODEL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the frame of cabinetry. Aligns appliance flush with the cabinetry. E AE C C D B D A A B B CAVITY DIMENSIONS A Overall height 2134 B Overall width 762 C Minimum overall depth* 635 D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return * 22 MM Assumes a door panel thickness of 3/4” (19mm).
DOOR PANEL DIMENSIONS — 760MM MODEL STAINLESS STEEL PANEL CUSTOM PANEL A A B B C C DIMENSIONS A Height of top door panel MM 1254 DIMENSIONS A Height of top door panel MM 1254 B Height of drawer door panel 772 B Height of drawer door panel 772 C Width of door panel 756 C Width of door panel 756 D Depth of door panel* 19 D Depth of door panel* min 16 - max 25 DOOR PANEL WEIGHT KG DOOR PANEL WEIGHT KG Weight of top door panel Weight of bottom drawer door panel * Excluding door handle.
CUSTOM DOOR PANEL INSTALL DIMENSIONS — 760MM MODEL Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. z z The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel. Measurements of screw hole locations can vary depending on the height of toe kick 50 – 152mm. 377.
DOOR CLEARANCE — 760MM MODEL 115° DOOR OPENING 90° DOOR OPENING B C Insert hinge limiting pin A A Before pushing the appliance into the cabinetry, insert the supplied hinge limiting pin into the borehole of the top hinge. The hinge limiting pin limits the door swing to 90°.
DRAWER CLEARANCE — 760MM MODEL DIMENSIONS A Maximum drawer extension when open* 400 B Maximum drawer extension when open** 461 * Excluding handle A B 26 MM ** Including handle
TOE KICK DIMENSIONS — 760MM MODEL STAINLESS STEEL TOE KICK PANEL CUSTOM PANEL TOE KICK PANEL Can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel. com for more information. For Custom door panel installation, a custom toe kick 2” – 6” (50 – 152mm) can be manufactured and fitted by cabinetmaker. The Custom door panel height needs to be adjusted accordingly. Extra lower grilles are required for a 2” (50mm) toe kick installation.
DUAL INSTALL OPTIONS The following are options for dual/multiple installation with reference to the door opening range and partition (optional) between two appliance combinations. Beware of clashing (circled) when opening the doors. Use a hinge limiting pin to restrict door opening rotation to 90°. Refer to ‘Door Clearance’ for more information.
CAVITY DIMENSIONS — 610MM + 610MM DUAL INSTALL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the frame of cabinetry. Aligns appliance flush with the cabinetry. E E C C D D A A B B DIMENSIONS A Overall height of cavity 2134 B Overall width of cavity 1219 C Minimum overall depth of cavity* 635 D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return * MM 3 102 Assumes a door panel thickness of 3/4” (19mm).
CAVITY DIMENSIONS — 610MM + 760MM DUAL INSTALL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the frame of cabinetry. Aligns appliance flush with the cabinetry. E E C C D D A A B B DIMENSIONS A Overall height of cavity 2134 B Overall width of cavity 1372 C Minimum overall depth of cavity* 635 D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return * 30 MM Assumes a door panel thickness of 3/4” (19mm).
CAVITY DIMENSIONS — 760MM + 760MM DUAL INSTALL FRAMELESS CABINETRY FRAMED CABINETRY Aligns appliance flush with the frame of cabinetry. Aligns appliance flush with the cabinetry. E E C C D D A A B B DIMENSIONS A Overall height of cavity 2134 B Overall width of cavity 1524 C Minimum overall depth of cavity* D Minimum cabinetry gap clearance from edge of door panels E Minimum required finished return * MM 635 3 102 Assumes a door panel thickness of 3/4” (19mm).
TOE KICK PANEL DIMENSIONS — DUAL INSTALL STAINLESS STEEL PANEL CUSTOM PANEL toe kick panel toe kick panel door panels door panels A A B TOE KICK PANEL (CA 25396) DIMENSIONS B RS61 + RS61 MODELS MM TOE KICK PANEL DIMENSIONS RS61 + RS61 MODELS MM A Width of toe kick 1216 A Width of toe kick 1216 B Height of toe kick 102 B Height of toe kick min 51 - max 152 TOE KICK PANEL (CA 25396) DIMENSIONS RS61 + RS76 MODELS MM TOE KICK PANEL DIMENSIONS RS61 + RS76 MODELS MM A Width of toe kick 1368
POWER SUPPLY DIMENSIONS SINGLE INSTALLATION DUAL INSTALLATION 1 1 2 2 1 1 A Electrical connection must be within this space if located behind the appliance and must not protrude from the back wall.
ELECTRICAL SPECIFICATION Power cord PLUMBING SPECIFICATION Power cord Water hose Supply 230 VAC, 50 Hz Service 10 amp circuit Socket 3-prong grounding-type Total length of power cord exiting product 1625mm 34 Water hose Supply 1/2” (12.
BEFORE INSTALLATION Check the cabinetry z Check the dimensions of the cabinetry: height, width, depth, floor level, finished alcove returns. Refer to 'Cavity Dimensions' for the correct measurements. Check the power supply and water connections z z z z z z z Ensure that there is a separate power socket for each appliance. Avoid sharing the power point with other appliances to prevent accidental switching off of the appliance. For power requirements, refer to the information on the serial plate.
INSTALL ANTI-TIP BRACKET Anti-tip bracket assembly kit overhead cabinetry Locating the attachment position of anti-tip bracket back wall stud Anti-tip bracket (1) B 1 Measure the height (A) of the attachment location from the floor to the alcove return and mark a horizontal line (B) at the back wall. z The height (A) must not exceed 2138mm to ensure the appliance does not tip over during installation. z Ensure there is a stud behind the wall.
INSTALL ANTI-TIP BRACKET Anti-tip bracket assembly kit For plaster board wall Fix the anti-tip bracket to the wall with #10x40mm cross head screws, and screw tightly with a screwdriver. Anti-tip bracket (1) Roll the appliance slowly into the cabinetry until the anti-tip bracket overlaps the back edge of the appliance. 180mm z Bracket Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold.
CONNECT WATER AND POWER SUPPLY Water fittings kit Connecting to water supply Collet locking clip (1) 1 Roll the appliance to the front of the cabinetry close enough to allow access at the back for power and water connection. 2 Insert the adaptor end of the braided hose through a hole at the rear of the plinth (A) and push all the way to the front of the appliance. 1/2 BSP Stainless steel braided hose with adaptor (1) A 6.
CONNECT WATER AND POWER SUPPLY Water fittings kit C 5 Insert the tube end of the adaptor fully into the PLV (C) at the bottom front of the appliance. Collet locking clip (1) 1/2 BSP Stainless steel braided hose with adaptor (1) D 6 Secure the connection with a locking clip between the PLV and hose end of adaptor (D). z Check the connection and open the water supply to test for leaks.
POSITION AND ALIGNMENT IN CABINETRY Install fasteners kit Attaching the barbed plugs 1 Before rolling into the cavity, insert a barbed plug into a large hole at the top left side (A) of the appliance. The plugs protect the inside surface of cabinetry from being damaged by screws when pushing in the appliance. Barbed plugs (2) Barbed plug Repeat steps 1 — 2 to the right side (B) of the appliance.
POSITION AND ALIGNMENT IN CABINETRY Install fasteners kit Attaching the depth alignment gauges 1 Loosen the right and left screws at the top and bottom sides of the door. (A) 2 Locate the alignment gauges at correct orientation to the right and left screws. Cabinet depth alignment gauge (4) Tools A Cross-head screwdriver Left Right 3 Position the alignment gauge by inserting the screw head through the keyhole of the gauge.
POSITION AND ALIGNMENT IN CABINETRY Positioning into the cabinetry 180mm 1 Roll the appliance slowly into the cabinetry until the anti-tip bracket overlaps the back edge of the appliance. Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold. Bracket PROFILE VIEW Be careful not to run over the water hose and power cord when rolling in the appliance.
POSITION AND ALIGNMENT IN CABINETRY Tools Aligning with the depth gauges 1 Mark the step of the depth gauges (A, B) on both sides of the door based on the thickness of door panel. z Example illustrations showing the door panel thickness (25.4mm ) marked on the gauges. Cross-head screwdriver Ruler B A Pencil Right Left C 2 Check if the gaps between appliance and cabinetry side walls are even on left and right sides (C, D).
POSITION AND ALIGNMENT IN CABINETRY Tools Cross-head screwdriver Adjusting the alignment in the cabinetry z Powered driver (optional) A A Front foot adjustment screw Rear foot adjustment screw z Clockwise turn of the front and rear adjustment screws (A) raise the height of the appliance. Counter-clockwise turn of the adjustment screws lower the height of the appliance.
SECURE APPLIANCE TO CABINETRY Install fasteners kit 8Gx16 Countersunk screw (6) Securing the top brackets Fix the top brackets to the ceiling surface of the cabinetry with 8Gx16 countersunk screws. (A) Tools Cross-head screwdriver A A Powered driver (optional) Securing the side brackets b b Fix the side brackets (2x) to the lower right and left sides of the cabinetry with 8Gx16 countersunk screws.
REMOVE HANGING BRACKETS Tools Powered driver 1 Remove the M8 nut (A) and M8 washer (B) from the M8 screw at the top of the refrigerator door using the supplied hex key and spanner. Repeat step for the drawer door. Use a 13mm socket wrench to tighten or loosen the M8 nut. a b M8 hex key top hanging bracket 13mm spanner 2 Remove the top and bottom hanging brackets (D, E) and set aside to use later. d 13mm socket wrench bottom hanging bracket 3 Loosen the M8 screw (C) by 1/8" (3mm).
INSTALL DOOR AND DRAWER PANELS STAINLESS STEEL PANELS Door handle kit CUSTOM PANELS M5 x 25 Remove the protective film around the handle attachment area of the stainless steel panel before installing the handle. M5x25 Hex screw (4x) blue tape Tools Attaching refrigerator door handle Attaching refrigerator door handle 1 Secure the door handle to the handle holes of the refrigerator door with M5x25 pan head socket screws.
INSTALL DOOR AND DRAWER PANELS Door panel attachment kit CUSTOM PANELS STAINLESS STEEL PANELS custom door panel Attaching top hanging bracket A A Side bracket (6) Bracket slider (6) 1 Secure the top hanging bracket (A) to the screw holes of the refrigerator door panel with 8Gx16 Mush washer screws.
INSTALL DOOR AND DRAWER PANELS Tools Hanging the refrigerator door panel A 1 Hold the door panel at an angle towards the top of the refrigerator door (A). b Powered driver (with 2.5mm drill bit) Cross-head screwdriver 2 Lower the screw holes of the hanging bracket onto the adjustment screws at the top of the refrigerator door. (B) b M4 hex key (1) A 3 Screw the M8 washer and nut to the adjustment screw and loosely tighten.
INSTALL DOOR AND DRAWER PANELS Tools Ensure the side brackets are loosely screwed when adjusting the height of the door panel. Do not adjust the door panel height when the side brackets are screwed tight. This can generate friction which causes the hanging brackets to bend. Cross-head screwdriver Adjusting height of door panel 1 Turn the adjustment screw to raise or lower the height of the door panel relative to the door. 2 Continue adjustment until gap with cabinetry is more than 3mm.
INSTALL LOCKING BRACKET INSTALL ADJUSTMENT BRACKETS Tools Cross-head screwdriver Cutter M4 hex key (1) 13mm spanner (1) A B 1 Loosen the screw at the bottom of the refrigerator door, and slide the locking bracket (A) out until it touches the panel. 2 Fix the locking bracket to the door panel with 8Gx16 countersunk screw (B). C D 1 Loosen the cap screws (C) of the adjustment brackets (D) on both sides of the plinth with a hex key.
INSTALL TOE KICK PANEL Miscellaneous components a 1 Re-attach the toe kick mounting plate (A) to the plinth using same screws that were set aside previously. 2 If toe kick depth is less than 92mm, attach an air toe kick seal (B) to the mounting plate. z Peel off the adhesive tape of air toe kick seal and attach to the middle of the back side of the mounting plate.
INSTALL TOE KICK GRILLES INSTALL TOP TRIM Tools Installing the top grille 1 Reattach the top grille (A) using the same screws set aside previously. Cutter a A Reinstalling the top trim Cross-head screwdriver 1 Slide one end of the top trim (A) into the hinge pocket of the appliance. 2 Press the other end to engage the dual lock strips on the non-hinge side of the appliance. Installing the bottom grille b 1 Reattach the bottom grille (B) to the mounting plate .
INSTALL WATER FILTER Supplied tools Inserting the water filter 1 Remove the packaging from the water filter. 2 Align the filter head with the slot of the filter removal tool and push until it clips in place. Water filter (1) filter removal tool Removing and replacing the filter 1 To remove the water filter, turn the filter removal tool anticlockwise and pull out the filter.
INSTALL AIR FLOW DIVIDER Miscellaneous components The air flow divider blocks the air flow from bypassing the front of the bottom grille. a 1 Remove the adhesive layer (A) off the air flow divider. Flow divider cap (1) Tools 2 Reinstall the air flow divider (B) to the bottom of the freezer drawer with screw. z Ensure the adhesive layer side of the divider contacts the door panel. 3 Press the flow divider firmly against the door panel. Hacksaw B B 4 Attach a flow divider cap (C) to the flow divider.
INSTALL CABINET SIDE TRIMS Install parts Dual adhesive strips are pre-attached at four locations along the side trim. 1 Peel off the liners from the dual adhesive strips (A). Cabinet side trim (2) 3 Hold the same angle and slide the side trim bottom end behind the lower hinge down to the bottom drawer side. (D) 4 Slide the side trim top end behind the top hinge.
INSTALL DOOR AND DRAWER SIDE TRIMS Trims install kit D b A c G Top door panel side extrusion (2) front of door Install door top extrusion Install drawer top and side trims 1 Align the top extrusion (A) to the top of the door, and match the notch (B) with the magnet housing (C). 2 Clip the trim caps (D) at both ends of top extrusion to both ends of the top of the door. 1 Remove the adhesive backing of adhesive strips pre-attached to the underside of the top trim (G).
DUAL INSTALLATION Install fasteners kit Attach central spacer to cabinetry Cabinet depth alignment gauges (4) 1 Measure the widths from the left (A) and right (B) cabinetry sides towards the centre to determine the spacer location. Top joiner Refer to "Cavity dimensions' page for correct width of the appliance. bracket kit A Central spacer (1) b 2 Mark the attachment location of the central spacer on the cabinetry ceiling using the depth alignment gauge (C).
DUAL INSTALLATION Install fasteners kit Attaching the depth alignment gauges A Cabinet depth alignment gauges (4) 1 Loosen the screws (A) at the cabinetry sides of the door and drawer of each appliance. 2 Locate the alignment gauges (B) at correct orientation to the right and left side screws. Barbed plugs (2) Tools b Left Right 3 Position the alignment gauge by inserting the screw head through the keyhole of the gauge.
DUAL INSTALLATION Tools Aligning the first appliance into the cabinetry min 7 1/16" (180mm) 1 Roll the first appliance (A) slowly into one side of the cabinetry until the anti-tip bracket (B) overlaps the back edge of the appliance. Ensure the bracket overlaps the appliance by a minimum 180mm for a secure hold. Refer to 'Install anti-tip bracket' for more information. Cross-head screwdriver A b Ruler PROFILE VIEW D 2 Align the top cap (C) of the first appliance flush with the front of the spacer (D).
DUAL INSTALLATION Install fasteners kit A Adjusting the height of first appliance in cabinetry 8Gx16 Countersunk screw (6) Rear foot adjustment screw Front foot adjustment screw Foot Tools 1 Turn the front and rear adjustment screws clockwise to raise height of the appliance and counter-clockwise to lower the height. A b Securing first appliance in cabinetry b 1 Fix the left and right top brackets (A, B) to the ceiling surface of the cabinetry with 8Gx16 countersunk screws.
DUAL INSTALLATION Tools Aligning the second appliance into the cabinetry min 180mm 1 Push the second appliance (A) to roll slowly into the other side of the cabinetry side by side with the first appliance. z Ensure the bracket (B) overlaps the appliance by a minimum 180mm for a secure hold. Refer to 'Install anti-tip bracket' for more information.
43453 M6 Washer M5 Washer DUAL INSTALLATION M5 x20 Cap Screw 248072 M6 x 12 Cap Screw 840371 8Gx16 Mush Washer M5x20 Cap screw (1) 847984 Top joiner fastener kit A B Securing the top brackets 1 Secure the top caps of both appliances to the central spacer with M5x20 cap screw (A) and washer (B). M5x16x1 Plain washer (1) 10 x 50 Dual Lock 2 Secure the top brackets to the ceiling surface of the cabinetry with 8Gx16 countersunk screws.
CHANGE THE DOOR HINGES (OPTIONAL) Tools You have the option to switch the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change kit is required for this installation, and must be purchased separately. T2 star-head screwdriver ‘0’ Cross-head screwdriver T20 screw Ensure that you remove all the shelves, covers and trims from the appliance before changing the hinges. Take care not to damage the door.
CHANGE THE DOOR HINGES (OPTIONAL) Tools A T2 star-head screwdriver b Removing the top door hinge C 1 Rotate the top hinge (A) outwards and remove the top hinge pocket cover (B) using the flat head screwdriver in the slot of the cover. 2 Unscrew M6x16 countersunk screws (C) to remove top hinge, and set aside to use later. 3 Unscrew M6x16 countersunk screws (D) from hinge pocket to remove hinge pocket and top alcove bracket. 4 Unscrew M5x12 countersunk screws (E) to remove top hinge bracket and spacer.
CHANGE THE DOOR HINGES (OPTIONAL) Tools Moving the sensor housing T20 star-head screwdriver Flat-head screwdriver 1 Unclip the hall sensor from the housing. 2 Unhook the interceptor board harness from sensor housing so harness is loose. 3 Remove the #8x16 screws (2x) from the sensor housing. 66 5 Reinstall the sensor housing using #8x16 screws (2x) into the pre-drilled holes in the cabinet top panel. 4 Move the sensor housing to align the opposite hall sensor clip with the centre of the cabinet.
CHANGE THE DOOR HINGES (OPTIONAL) Hinge change assembly D Reinstalling the top hinge c 1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk screws (A) on the new hinge side at the other side of the appliance. 2 Install the new hinge pocket and alcove top bracket on the new hinge side using two (2x) M6x16 countersunk screws (B). z The new hinge pocket and top alcove bracket are supplied with the hinge kit.
CHANGE THE DOOR HINGES (OPTIONAL) Hinge change assembly L FIL N L FIL A use new top adaptor bracket NO NO L IL OF L FIL L FIL L L FIL FIL IF NO NO NO K05 top adaptor bracket R/L (1) LL ON L FIL IF LL K05 bottom adaptor bracket R/L (1) IF LL Changing the top door bracket ON 1 Unscrew the M5x10 screws (4x) to remove the top adapter bracket from the top of the door (A). 2 Install the new top adapter bracket into the other side of the top of the door with M5x10 screws (4x) (B).
CHANGE THE DOOR HINGES (OPTIONAL) Tools A T2 star-head screwdriver Reinstalling the door Flat-head screwdriver 1 Secure the door to the top and middle hinges of the appliance using M6x10 hex screws (4x). (A) A Hex key NO B FIL L L FIL NO L FIL NO L FIL 2 Activate the hinge spring by turning the star T20 screws to the I position. (B) 3 Return the appliance to the upright position, and reinstall all covers and trims.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models F Check all parts are installed. F Ensure the appliance is level. F nsure the appliance is securely fastened to the cabinetry with the E supplied anti-tip bracket and fittings. F nsure the door can open and close freely with no resistance from E surrounding cabinetry. F Ensure hinge limiting pin is fitted for 90° door swing. F nsure all internal and external packaging is removed from the appliance E before use.
FISHERPAYKEL.COM © Fisher and Paykel Appliances 2020. All rights reserved. The appliance specifications in this document apply to the specific appliances and models described at the date of issue. Under our policy of continuous appliance improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this document correctly describes the appliance currently available.
