ACTIVESMART™ INTEGRATED REFRIGERATOR FREEZER RS9120W models INSTALLATION GUIDE NZ AU GB IE HK SG IN
CONTENTS 1 SAFETY AND WARNINGS 2 COMPONENTS 3 TOOLS 4 APPLIANCE AND CAVITY DIMENSIONS 5 CABINETRY OPTIONS 6 STAINLESS STEEL DOOR PANEL AND TOE KICK DIMENSIONS 7 CUSTOM DOOR PANEL AND TOE KICK DIMENSIONS 8 CUSTOM DOOR PANEL INSTALLATION DIMENSIONS 9 CUSTOM DOOR PANEL INSTALLATION TEMPLATE !0 DOOR CLEARANCE !1 ELECTRICAL AND PLUMBING !2 BEFORE INSTALLATION !3 CAVITY PREPARATION !4 WATER AND POWER SUPPLY CONNECTION !5 TOP TRIM INSTALLATION !6 SIDE BRACKET INSTALLATION !7 POSITIONING INTO CABINETRY !8 ALIGNING
1 ! SAFETY AND WARNINGS WARNING! Electric Shock Hazard Read and follow the safety and warnings outlined in this installation guide before operating this appliance. Failure to do so can result in death, electric shock, fire or injury to persons. ! WARNING! Cut Hazard Take care — panel edges are sharp. Failure to use caution could result in injury or cuts.
2 COMPONENTS Internal box (Installation kit) Located inside the appliance A Anti-tip bracket assembly kit B Door panel attachment kit C Door / drawer trim install kit D Cabinet side trim install kit Dual adhesive tabs (12) Side trim bracket (6) Masonry plug (4) Side strap (10) Side cover (2) Spring clip (6) 8x16 mush washer screw (36) Top cover (4) #8 x 16 Mush Washer Twin Thread Philips Screw #10x40 cross-head screw (4) E Top trim install kit #8 x 16 Mush Washer Twin Thread Philips S
2 COMPONENTS External box Located at back panel of appliance Ice and Water display (Ice and Water models only) Located inside the appliance Door side trim (2) Drawer side trim (2) Cabinet side trim (2) Double-sided door panel template (1) Top trim (1) Drawer top trim (1) Top grille (1) Toe kick (1) Miscellaneous items pack Located inside the appliance ACTIVESMART™ External display module (1) Toe kick filter Located inside the appliance Water fittings kit (Ice and Water models only) Located i
2 3 COMPONENTS Door panel set Not supplied and must be purchased separately Stainless steel (Fisher & Paykel) door panel set: Includes 1x single door panel and 1x drawer panel. Non-water dispensing door panel set (RD9120W / RD9121W) Ice and Water door panel set ( RD9120WRU / RD9121WRU) M5x14 mush cross-head (SS) screw (24) Door handle kit Not supplied and must be purchased separately.
4 APPLIANCE AND CAVITY DIMENSIONS IMPORTANT! c For ease of installation, ensure cavity width is consistent f j top to bottom and height is consistent left to right.
5 FRAMELESS CABINETRY (Aligns the appliance with the cabinetry) CABINETRY OPTIONS FRAMED CABINETRY (Aligns the appliance with the frame of the cabinetry) Note: Shown with custom panel and handle attached to fridge Note: Shown with custom panel and handle attached to fridge Note: Drawings are only for reference and not the actual cavity width of the cabinetry.
6 STAINLESS STEEL DOOR PANEL AND TOE KICK DIMENSIONS c Available on Ice and Water models only Available on Ice and Water models only a a a b b b D DOOR PANEL SET RD9120W / RD9120WRU D DOOR PANEL SET RD9121W / RD9121WRU d e RD9120W / RD9120WRU RD9121W / RD9121WRU DOOR PANEL SETS DIMENSIONS mm mm TOE KICK PANEL DIMENSIONS mm a Height of top door panel 1150 1252 d Height of toe kick panel 102 b Height of bottom drawer panel 772 772 e Depth of toe kick (measured from front of door p
7 CUSTOM DOOR PANEL AND TOE KICK DIMENSIONS IMPORTANT! Custom door / drawer panels are applicable for Non-water dispensing models only.
8 CUSTOM DOOR PANEL INSTALLATION DIMENSIONS The drawings below apply to Non-water dispensing models only (RS9120WRJ and RS9120WLJ). Dimensions apply for the preparation and installation of custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. 764mm 558mm 347mm 141mm Ø2mm REF 14x Pilot holes recommended for bracket attachment. (Do not penetrate front surface).
DRAWER PANEL LEFT SIDE DRAWER PANEL RIGHT SIDE HANGING BRACKET HOLES HANGING BRACKET HOLES SIDE BRACKET HOLES DOOR PANEL LEFT SIDE DOOR PANEL RIGHT SIDE FISHER & PAYKEL APPLIANCES LIMITED TITLE: GRAPHICS RS9120 DOOR TEMPLATE REVISION: 1 DATE: 04/04/2019 SCALE: 1:1 DOOR PANEL RIGHT SIDE 1 REV DOOR PANEL LEFT SIDE ECN DOOR PANEL RIGHT SIDE HANGING BRACKET HOLES DRAWER PANEL LEFT SIDE HANGING BRACKET HOLES PRINT SPECIFICATION DOOR PANEL RIGHT SIDE SIDE BRACKET HOLES 400mm BJ CHKD REVISION
!0 DOOR CLEARANCE d e b c b c Insert hinge limiting pin A a WARNING! ●● ●● 115° DOOR OPENING (FULL INTERNAL ACCESS) 90° DOOR OPENING For 90° door swing, a hinge limiting pin is supplied with your appliance. This pin fits in the boreholes of the top hinge. 1 Open door to 90°. 2 Insert the hinge limiting pin vertically into the bore hole. Wall 115° DOOR OPENING [FULL ROTATION] 90° DOOR OPENING –– Apply a gentle tap to the pin if it does not slide smoothly.
!1 IMPORTANT! ●● ●● A ELECTRICAL AND PLUMBING Electrical connection should be located in an adjacent cabinet to either side of the appliance or above the appliance cavity. We recommend to use an isolating switch that is easily accessible to the user after the appliance is installed. WARNING! ●● ●● Electrical shock hazard. Assume all parts are live. Disconnect supply before servicing and installation.
!1 ELECTRICAL AND PLUMBING Maximum distance of hose and power cord Power cord (excluding plug) — 800mm LEFT HAND SIDE RIGHT HAND SIDE Water inlet hose — 1350mm Water inlet hose — 2120mm Power cord (excl. plug) — 2051mm Power cord (excl. plug) — 2051mm ELECTRICAL SPECIFICATIONS PLUMBING SPECIFICATIONS Supply 230V, 50 Hz Service 10 amp circuit Supply Pressure 13mm or 19mm BSP threaded water connection 6.
!2 BEFORE INSTALLATION IMPORTANT! ●● ●● ●● ●● Be careful when unpacking to prevent damage to the surface of your appliance. Ensure that the appliance is stable to prevent from tipping over when unpacking. Do not open the doors to prevent the appliance from tipping over. The appliance is heavy and requires a minimum of 2 persons to unpack and install. Checking your appliance ●● ●● ●● Ensure that the feet of the appliance are retracted. If the appliance is damaged, contact your Fisher & Paykel dealer.
!2 BEFORE INSTALLATION IMPORTANT! ●● ●● ●● Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven or dishwasher. The appliance has front and rear rollers for moving the appliance forward and backward. Do not move the appliance sideways to avoid damaging the rollers or the floor covering/surface.
!3 IMPORTANT! Internal box ●● A Anti tip bracket kit ●● ●● Anti-tip bracket (1) CAVITY PREPARATION The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand 100kg load. Ensure that anti-tip bracket is installed correctly to prevent the appliance tipping forward when door is open. Ensure the bracket is secured to structural beams or wall studs nearest to the center of the alcove.
!4 IMPORTANT! Water fittings kit ● ● ● ● Water tap adaptor (1) WATER AND POWER SUPPLY CONNECTION Ensure that the water connection is performed by a professional installer. The product comes with a pre-connected plastic water tubing. Water fittings are not supplied and must be purchased separately. Ensure the appliance is connected to its own isolating switch. ● ● Ensure there is enough tubing for the water connection and to pull the appliance out for service, if required.
!5 WARNING! Internal box ●● E Top trim install kit TOP TRIM INSTALLATION ●● Be careful when working with the appliance outside of the finished enclosure. Ensure that the appliance is secured to prevent tipping forward. Tipping of appliance can lead to serious injury or death. Install top trim — for 2134mm cavity only Cabinet top trim bracket (2) 1 Insert M5 nuts (A) into ~3 3 At the top of the 30 the top and bottom side of the left and right ends of the top trim.
!6 IMPORTANT! Internal box ●● F Side bracket install kit SIDE BRACKET INSTALLATION ●● Ensure all external packaging materials are removed from the appliance before installation. Ensure the door of the appliance is closed during installation. Attach side base brackets Side base brackets (R/L) (2) 1 Fix the side base brackets to the base left and right sides of the appliance with M5x8 countersunk cross-head screws (A). 2 Loosely screw (1 – 2 turns) M5x10 cross-head screws into the doors (B).
!7 POSITIONING INTO CABINETRY IMPORTANT! ●● Ensure the hose is not run over by the appliance when pushing into the cabinetry to prevent damage and possible water leaks. Position the appliance into the cabinetry 1 Coil the excess water hose and power cord flat behind the appliance (A). 2 Push the appliance into the cabinetry until the anti-tip bracket overlaps the rear top edge of the appliance (B), and the doors are in line with the cabinet frame. IMPORTANT! ●● ●● Ensure the appliance is centered.
!8 IMPORTANT! Tools ●● ●● ●● Hex key ALIGNING INSIDE CABINETRY ●● ●● Ensure all four corners of the appliance is supported firmly onto the floor to eliminate any movement. DO NOT install the appliance on a soft, uneven, or unlevelled floor to avoid twisting the appliance and poor door sealing. Raise the appliance using a 11mm hex socket or 4mm hex key. One turn of height adjusting nuts is equivalent to 1mm height adjustment. Note: Maximum travel is 20mm.
!9 IMPORTANT! Internal box B Door panel attachment kit DOOR PANEL INSTALLATION — STAINLESS STEEL ●● ●● ●● Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. Ensure to protect the finish of the Stainless steel door panels. For non-water dispensing door panels: Leave the protective film on the panels when hanging and remove the film only when installation is complete.
!9 Ice and Water display (Ice and Water models only) DOOR PANEL INSTALLATION — STAINLESS STEEL IMPORTANT! ●● ●● Failure to follow these steps can lead to difficulties in door panel adjustment and cosmetic cap fitment. For water dispensing door panels: Remove the protective film from the appliance doors before hanging door panels. Connect the external display module (for Ice and Water models only) External display module (1) 1 Remove the external display module taped to the front of the appliance.
!9 Tools DOOR PANEL INSTALLATION — STAINLESS STEEL Attach the door panels 1 Open the door and loosen the M5x10 cross-head screws (do not remove) at the sides of the doors (A). 2 Hang the door panel by inserting the M8 studs through the holes of the hanging bracket (B). FPA spanner 3 Slide the forks of the side brackets onto the screws of the door (C).
!9 B Door panel attachment kit DOOR PANEL INSTALLATION — STAINLESS STEEL IMPORTANT! ●● Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. Adjust the door panels 8x16 mush washer screw (1) Tools 1 Place a ruler on the front of the appliance to check flushness top and bottom, left and right. –– Ensure the gap between the top of the door panel and the top cabinetry is not more than 7mm.
DOOR PANEL LEFT SIDE SIDE BRACKET HOLES 91/40/40 JB NOITACIFICEPS TNIR DKHC SNOISIVER 1 NCE VER DETIMIL SECNAILPPA LEKYAP & REHSIF DOOR PANEL LEFT SIDE EDIS THGIR LENAP ROOD SELOH TEKCARB EDIS DRAWER PANEL LEFT SIDE ETALPMET ROOD 0219SR SCIHPARG :ELTIT DOOR PANEL LEFT SIDE DOOR PANEL LEFT SIDE Align right side edge of template with right side edge of top door panel. 4B DOOR PANEL LEFT SIDE Align bottom of template with bottom edge of top door panel.
849548 849548 @0 DOOR PANEL INSTALLATION — CUSTOM IMPORTANT! back side of drawer panel The template should be placed on the back side of the door panel. 6 To mark the drill locations of middle screw holes, align the screw holes of drawer hanging bracket with right and left drilled screw holes. Drill screw holes to marked locations. DRAWER PANEL RIGHT SIDE DRAWER PANEL RIGHT SIDE HANGING BRACKET HOLES Align top of template with top edge of drawer panel.
@0 Internal box B Door panel attachment kit DOOR PANEL INSTALLATION — CUSTOM Remove hanging brackets 1 Remove the M8 washers and M8 nuts from the M8 studs at the top the door (A) using the hex key and spanner. Keep the washers and nuts to reuse later. 2 Remove the hanging bracket from the top of each door and set aside (B) for later installation.
@0 Tools DOOR PANEL INSTALLATION — CUSTOM Attach the door panels 1 Open the door and loosen the M5x10 cross-head screw (do not remove) at the sides of the doors (A). 2 Hang the door panel by inserting the M8 studs FPA spanner through the holes of the hanging bracket (B). 3 Slide the forks of the side brackets onto the screws of the door (C). 4 Screw the M8 washer and nut to the stud (D), Hex key and re-tighten the side screws (E) to fix the door panel (do not fully tighten).
@0 B Door panel attachment kit DOOR PANEL INSTALLATION — CUSTOM IMPORTANT! ●● Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. Adjust the door panels 8x16 mush washer screw (1) Tools 1 Place a ruler on the front of the appliance to check flushness top and bottom, left and right. –– Ensure the gap between the top of the door panel and the top cabinetry is not more than 7mm.
@1 Internal box FIXING TO CABINETRY Attach fixing brackets Fixing bracket install kit G Fixing bracket (4) C M5x8 countersunk cross-head screw (8) A Screw cover (4) M5 x 8 Countersunk Philips Screw #8x19 twin thread screw (8) 1 Open the top door carefully. 2 Place the fixing brackets on the top and side base 4 Slide the screw cover between the fixing bracket and the side bracket on the appliance (C). brackets of the appliance and secure mid-way with M5x8 countersunk cross-head screws (A).
@2 Miscellaneous items pack WATER FILTER INSTALLATION IMPORTANT! ●● The water filter head must be firmly pushed into the appliance and secured. incorrect installation can lead to water leaks. Water filter (1) A Filter handle B Filter cartridge tool (1) Front view Filter in locked position Install the water filter 1 Remove the plastic wrapping of the new filter. 2 Pull the freezer drawer out slightly and insert the filter into the casing at the bottom left corner of the appliance.
@3 External box TOE KICK INSTALLATION Install the toe kick filter and grille 1 Fit the filter onto the rails and push until it clips securely (A). 2 Align the top grille clips to the top plinth slots. Ensure the top grille is in the correct orientation (B). 3 Push the grille firmly onto the appliance until the clips engage (C).
@3 ●● E CUT UNREQUIRED VANES FROM DOTTOM 2. DRILL HOLES THROUGH DIMPLES The standard appliance includes a stainless steel toe kick 102mm and the components required to mount SCREWS the toe kick.TO FIX GRILL TO 3. USE PROVIDED 1. IF TOEKICK Alternatively, the customer can1.supply own custom toe kick 102 –4" 152mm complete integration of the appliance.
@4 Internal box C Door / drawer trim install kit DOOR AND DRAWER TRIMS INSTALLATION Attach the covers Attach the drawer top and side trims 1 Open the top door. Attach the top cover 3 Peel off two dual adhesive tabs and press them (A) firmly over the top stud on the handle side of the door. together to form a pair (E). Remove the adhesive backing on one side only. 4 Press firmly to the underside of the drawer top trim in the indicated locations (F).
TWO METHODS ARE AVAILABLE FOR ATTACHING CABINET SIDE TRIMS: [A] FLEXIBLE SPRING CLIP METHOD — RECOMMENDED METHOD [B] FIXED SCREW METHOD — METHOD TO USE IF CABINET IS NOT TO SPECIFICATION (Attempt method [A]. If method [A] results in poor fitment of side trims due to cabinetry that is uneven or out of specification, use method [B]).
@5 CABINET TRIMS INSTALLATION — [A] FLEXIBLE SPRING CLIP METHOD 5 Insert the spring clip into the gap between the side trim and side trim bracket, orientation as shown in figures (D) and (E). 6 Open the French doors. Place the assembled side trim with brackets and spring clips against the alcove side wall with the shorter lip facing the bottom (F). IMPORTANT! IMPORTANT! Repeat for the remaining side trim.
@6 Internal box D CABINET TRIMS INSTALLATION — [B] FIXED SCREW METHOD 1 Break off the datum lip to each side trim bracket and discard. Repeat for all side trim brackets. Cabinet side trim install kit Side trim bracket (6) 4 Position three side trim brackets on one side trim. Refer to (B) for bracket locations. 5 Open the French doors. Measure 50mm from the front of cabinet (from behind the doors), to the front of the alcove and accurately mark a vertical line (C).
@6 CABINET TRIMS INSTALLATION — [B] FIXED SCREW METHOD 7 Place the side trim against the alcove side wall with the shorter lip facing the bottom (E). –– Ensure the side trim is positioned as high as it will go. Side trim Suggest engagem “ensure t F G Side trim bracket Top view of side trim engaged correctly in side trim bracket 8 Engage the side trim with the brackets by pushing the trim inwards at the locations of the top and middle side trim brackets.
@7 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Ensure all internal and external packaging is removed from the appliance before use. Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the doors / drawer can open and close freely with no resistance from surrounding cabinetry. Ensure hinge limiting pin is fitted for 90° door swing.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The appliance specifications in this document apply to the specific appliances and models described at the date of issue. Under our policy of continuous appliance improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the appliance currently available. NZ AU GB IE HK SG IN 846806D 07.
