VACUUM SEAL DRAWER MINIMAL VB60SDEB1 CONTEMPORARY VB60SDEX1 INSTALLATION GUIDE NZ AU GB IE SG
CONTENTS Safety and warnings 4 Vacuum seal drawer models 5 Unpack your product 6 Electrical specifications 6 Parts supplied 7 Tools required 7 Product dimensions - minimal & contemporary models 8 Cabinetry dimensions - minimal & contemporary models Installation options 9 10 Prior to installation 11 Installing the drawer 12 Adjusting the height 13 Installer checklist 14 3
SAFETY AND WARNINGS ! WARNING! Tip Hazard This product may tip. Keep children away and take care. Failure to follow this advice may result in injury. • Drawer must be secured in place by supplied screws. • Ensure there is a fixed shelf directly above the drawer if it is not installed under another product. ! WARNING! Cut Hazard Failure to use caution could result in injury. • Take care: some edges may be sharp. • Do not put fingers in the drawer when closing.
SAFETY AND WARNINGS VACUUM SEAL DRAWER MODELS READ AND SAVE THIS GUIDE To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety guides listed below. Read all the instructions before using the appliance. Installation z z z z z z z z Please make this information available to the person installing the product.
UNPACK YOUR PRODUCT ELECTRICAL SPECIFICATIONS Remove the Vacuum Seal Drawer and accessories box from the packaging. Recycle the materials that can be reused. Dispose packaging materials in accordance with local regulations on waste disposal. Inspect the Vacuum Seal Drawer for any signs of damage. Do not install the Vacuum Seal Drawer if it has been damaged. If the product is damaged, contact your local Fisher & Paykel dealer.
PARTS SUPPLIED TOOLS REQUIRED VACUUM SEAL DRAWER VACUUM SEAL DRAWER MINIMAL VB60SDEB1 CONTEMPORARY VB60SDEX1 MINIMAL VB60SDEB1 CONTEMPORARY VB60SDEX1 SERVICE & WARRANTY SERVICE ET GARANTIE ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ SERVIZIO E GARANZIA SERVICE & GARANTIE HUOLTO JA TAKUU SERVICE OG GARANTI 保修和维修 USER GUIDE 服務和保修 NZ AU UK IE SG INSTALLATION GUIDE NZ AU GB IE SG Service & Warranty User guide Installation guide 4x20 T20 star head countersunk screw (2) T20 star head screw 4x15 (4) Anti-tip bracket (2) 5
PRODUCT DIMENSIONS - MINIMAL & CONTEMPORARY MODELS E C PRODUCT DIMENSIONS H I ISOMETRIC MM A Overall height of drawer 140 B Overall width of drawer 596 C Overall depth of drawer* 566 D Height of chassis 140 E Width of chassis** 556 F Depth of chassis*** 546 G Height of drawer front panel H Depth of drawer front panel and flange PLAN VB60SD I Depth of open drawer J Height from bottom of chassis to bottom of front panel K Depth from front of door to side bracket 136 20 414 2 384 * Include
CABINETRY DIMENSIONS - MINIMAL & CONTEMPORARY MODELS PROUD INSTALL d b PO* e a PO* c f PROFILE PLAN FLUSH INSTALL CABINETRY DIMENSIONS VB60SD MM A Minimum inside height of cavity 142 B Minimum inside width of cavity 560 C Minimum inside depth of cavity 572 D Overall width of cabinetry 600 E Minimum clearance between top of front panel and upper cabinetry panel 3 F Minimum clearance between bottom of front panel and lower cabinetry panel 2 * The power outlet (PO) must be earthed and lo
INSTALLATION OPTIONS STANDALONE INSTALLATION COMBINED WITH SINGLE OVEN COMBINED WITH COMPANION PRODUCT Suitable for Minimal and Contemporary 60cm Vacuum seal drawers. A fixed shelf must be installed above the drawer. The 60cm Vacuum seal drawer can fully support a 60cm Fisher & Paykel wall oven. The 60cm Vacuum seal drawer can fully support a 60cm Fisher & Paykel companion product.
PRIOR TO INSTALLATION INSTALL THE AIR FILTER REMOVE THE TRANSIT SCREWS The transport screws must be removed before starting up for the first time to avoid damage to the drawer. power cable holder Unscrew the transport screws from under the power cable and holder. transport screws locking cap 1 Pull out the locking cap with pliers. INSTALL THE ANTI-TIP BRACKETS 2 Insert the locking cap in the holder.
INSTALLING THE DRAWER 1 2 Connect the power plug into the power outlet. Slide the drawer carefully into the cabinetry. Push the drawer back into the cabinetry, and align the front panel* with the cabinetry as desired. Ensure the side brackets engages the anti-tip brackets. * Flush alignment illustrated. 12 3 Open the drawer and extend fully. 4 Secure the attachment flanges of the drawer to the side edges of cabinetry with 4x20 T20 star head countersunk screws.
ADJUSTING THE HEIGHT The front panel of the drawer can be adjusted vertically to align with the surrounding cabinetry. 1 Open the drawer fully, and slightly loosen the two screws. 2 Adjust to the required height and then re-tighten the screws. The height is adjustable within 5mm. 3 Close the drawer and check the alignment. Adjust again if necessary.
INSTALLER CHECKLIST IMPORTANT! FP WARMER DRAWER INTERFACE LOGIC_V1 USER PRESSES ON/OFF BUTTON 1h Read all installation instructions in this manual to see if the unit has been correctly installed. Ensure that installation has been completed correctly before use.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2020. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
