INSTALLATION INSTRUCTIONS USER GUIDE WashSmart™ Eco, WashSmart™ and QuickSmart™ Washers WA1060E, WA8560E, WA8060E, WA7560E, WA7060E, WA8560G, WA8060G, WA7060G and WA7060M models NZ AU SG ROW
CONTENTS Introduction 3 Safety and warnings 4 Installation instructions 5 Before you do your first wash 11 Getting started quickly – WashSmart™ Eco washer 12 Getting started quickly – WashSmart™ washer 14 Getting started quickly – QuickSmart™ washer 16 Washer controls 18 Washer safety features 19 Eco-Active™ wash – WashSmart™ Eco washer only Sorting 20 21 Loading 22 Detergent 23 Fabric softener 24 Wash cycles – WashSmart™ Eco washer 25 Wash cycles – WashSmart™ washer 26 Wash cy
INTRODUCTION Welcome to your Fisher & Paykel clothes washer Thank you for buying a Fisher & Paykel washer. We are proud of this washer and trust it will serve you well for many years. At Fisher & Paykel we aim to provide innovative products that are simple to use, ergonomic and kind to the environment. Thousands of tonnes of washing and over 80 years of laundry experience have been programmed into your washer to help give you the best possible performance.
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet box), ensure that it is positioned so that it does not come into contact with water or moisture. Failure to do so may result in death or electrical shock.
INSTALLATION INSTRUCTIONS Product and minimum clearance dimensions H A D A B C F G FRONT VIEW PROFILE VIEW WA**60* PRODUCT DIMENSIONS mm A Overall height of product † (to highest point on console) B E 1045 – 1075 Overall width of product 600 C Depth of product 600 D Height of product to top of lid † (closed) 950 – 980 E Height of lid open † (measured from bottom of product) 1350 – 1385 Standpipe height min.
INSTALLATION INSTRUCTIONS Unpacking To ensure the best performance from your new washer please follow the instructions below. Removing the packaging 1 Remove the outer packaging. 2 Tilt the washer backwards and walk it off the 3 4 5 6 base packer one foot at a time (ensure the lid is still taped down). Remove the base packer from under the washer by tilting the washer backwards and pulling the packer out the front. Remove the tape, lift the lid and remove the bowl packer from the bowl.
INSTALLATION INSTRUCTIONS Electrical connection ●● ●● ●● ●● This appliance must be supplied with a 220 – 240 V, 50 Hz, sinusoidal, 10 A electrical supply. Check the power cord for damage, making sure it is not squashed or twisted. A damaged power cord must be replaced by a Fisher & Paykel trained and supported service technician, in order to avoid a hazard. The appliance must not be operated until it is repaired, as there is a risk of electric shock.
INSTALLATION INSTRUCTIONS Inlet hoses IMPORTANT! WARNING: Failure to adhere to the following instructions may result in a flood and damage to property. ●● ●● ●● ●● New hose sets provided with the washer shall be used to connect the washer to the water supply. Old hose sets should not be used. We recommend replacing the inlet hoses every 5 years. Hoses should be checked from time to time and replaced if any wear, cuts, bulges, kinks or leaks are found.
INSTALLATION INSTRUCTIONS Levelling instructions It is IMPORTANT to level the washer to ensure good spin performance. A spirit level is provided with your washer. Use this to level your washer, always placing it on a clean, flat surface. The washer is level when the bubble sits in the centre, within the two lines. Your washer is equipped with self-locking feet at the front to ensure they do not move once you have levelled your washer.
INSTALLATION INSTRUCTIONS Completing your installation ●● ●● ●● Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hoses. Check the hose connections for leaks again after 24 hours. Uncoil power cord, remove and discard the plastic pin cover, and plug into wall socket. Connect the appliance to an earthed outlet protected by a fuse of suitable capacity. IMPORTANT! Do not touch or operate the washer with wet hands or with bare feet.
BEFORE YOU DO YOUR FIRST WASH You owe it to yourself and your washer to have your washer installed correctly. Before you start, it is a good idea to go through the following checklist: 1 Has the base packer been removed? Refer to page 6. 2 Is the drain hose threaded through the ‘U bend’ (with no more than 20 mm extended) and hooked into your tub or standpipe? Refer to page 6. 3 Is the hot hose connected to the Hot valve marked ‘H’? Is the cold hose connected to the Cold valve marked ‘C’? Refer to page 8.
GETTING STARTED QUICKLY – WASHSMART™ ECO WASHER Before you start ●● ●● ●● ●● ●● ●● ●● It is important to sort your clothes, particularly separating white/light colours from dark colours, as well as separating out sheets and towels. Refer to the ‘Sorting’ and ‘Loading’ sections. Wash new, highly coloured and dark coloured items separately to prevent dye transfer onto other items. Sort lint givers and lint collectors (refer to the ‘Sorting’ section). Close bra clasps, do up zippers and check pockets.
GETTING STARTED QUICKLY – WASHSMART™ ECO WASHER Using your washer The buttons require only a gentle touch to activate. to activate your WashSmart™ Eco washer. 1 Touch ‘POWER’ 2 Select your desired wash cycle by gently touching the wash cycle button of your choice (refer to ‘Wash cycles’ section). 3 Choose your wash options, eg you may want a ‘Warm’ wash temperature and a ‘Slow’ spin speed (refer to the ‘Wash options’ section). to start the cycle.
GETTING STARTED QUICKLY – WASHSMART™ WASHER Before you start ●● ●● ●● ●● ●● ●● ●● It is important to sort your clothes, particularly separating white/light colours from dark colours, as well as separating out sheets and towels. Refer to the ‘Sorting’ and ‘Loading’ sections. Wash new, highly coloured and dark coloured items separately to prevent dye transfer onto other items. Sort lint givers and lint collectors (refer to the ‘Sorting’ section). Close bra clasps, do up zippers and check pockets.
GETTING STARTED QUICKLY – WASHSMART™ WASHER Using your washer The buttons require only a gentle touch to activate. to activate your WashSmart™ washer. 1 Touch ‘POWER’ 2 Select your desired wash cycle by gently touching the wash cycle button of your choice (refer to ‘Wash cycles’ section). 3 Choose your wash options, eg you may want a ‘Warm’ wash temperature and a ‘Slow’ spin speed (refer to the ‘Wash options’ section). to start the cycle.
GETTING STARTED QUICKLY – QUICKSMART™ WASHER Before you start ●● ●● ●● ●● ●● ●● ●● It is important to sort your clothes, particularly separating white/light colours from dark colours, as well as separating out sheets and towels. Refer to the ‘Sorting’ and ‘Loading’ sections. Wash new, highly coloured and dark coloured items separately to prevent dye transfer onto other items. Sort lint givers and lint collectors (refer to the ‘Sorting’ section). Close bra clasps, do up zippers and check pockets.
GETTING STARTED QUICKLY – QUICKSMART™ WASHER Using your washer The buttons require only a gentle touch to activate. to activate your QuickSmart™ washer. 1 Touch ‘POWER’ 2 Select your desired wash cycle by gently touching the wash cycle button of your choice (refer to ‘Wash cycles’ section). 3 Choose your wash options, eg you may want a ‘Warm’ wash temperature and a ‘Slow’ spin speed (refer to the ‘Wash options’ section). to start the cycle.
WASHER CONTROLS SmartTouch™ buttons The smooth, easy clean buttons require only a gentle touch to activate. Use these to power your washer on and off, start and pause your washer, select your cycle and wash options, activate keylock and programme a delay start. Digital display screen The digital display screen provides feedback on how long the wash cycle has to go, to keep you informed throughout the cycle.
WASHER SAFETY FEATURES Lid Lock The lid of your washer is locked for some parts of the wash cycle, ensuring safety for you and your family while it is operating. The ‘Lid Locked’ light (above the button) is illuminated when the lid lock is activated, letting you know at a glance if you can open the lid or not. To unlock the lid at any time during the cycle touch . Lid Lock If the lid is left open, your washer will be unable to lock the lid, and the cycle will be halted.
ECO-ACTIVE™ WASH – WASHSMART™ ECO WASHER ONLY Your WashSmart™ Eco washer uses a dual-action wash to give excellent wash performance whilst taking great care of your clothes. We call this the Eco-Active™ wash. The two parts to the Eco-Active™ wash are explained below: Detergent activating wash (front-loader type wash) For both ‘Eco-Active™, On’ and ‘Eco-Active™, Off’ selections, your WashSmart™ washer fills the bowl at the selected temperature with just enough water so that your clothes are 100% saturated.
SORTING Sorting To get the best wash results it pays to sort your clothes before washing. Care labels The care label will tell you about the fabric of the garment and how it should be washed. Machine Washable Warm 40°C maximum Rinse Well Normal Spin Do not bleach Tumble drying possible, maximum 60°C Warm iron Do not dry clean Examples of different care label symbols. Soil Sort clothes according to the type and amount of soil.
LOADING Loading Check pockets Loose items can damage both your washer and your clothes. Close zippers, hooks and eyes This is to make sure that these items do not snag on other clothes. Mend any torn garments or loose buttons Tears or holes may become larger during washing. Remove any loose bra wires as they can damage your washing machine and/or dryer. Pretreat any stains Make sure you use an appropriate surface to apply treatments.
DETERGENT Choosing the right detergent ●● ●● ●● ●● We recommend using domestic laundry detergent. Use powder or liquid detergent for ‘Top Loader’ washers. When washing wool items, remember to use a detergent specifically recommended for woollens. Soap flakes or granulated soap powders should not be used in your washer. Pods - Detergent pods are a ‘no mess’ alternative to powdered or liquid detergent. They should be placed down the centre of the agitator.
FABRIC SOFTENER How the fabric softener is dispensed The fabric softener goes into the dispenser cup on the top of the agitator. During the rinse the washer spins to release the fabric softener, delivering it down the agitator stem as the washer fills for the final deep rinse. If fabric softener is not added to the washer correctly, it may contribute to ‘scrud’ (described below).
WASH CYCLES – WASHSMART™ ECO WASHER WASH TIME * WASH ACTION WASH TEMP RINSE SPIN SPEED SPIN TIME ** For normally soiled everyday cotton loads, eg t-shirts, shorts, shirts. 11 minutes Regular Warm/ Cold Spray/ Deep Rinse 1100 rpm 6 minutes Recommended cycle for heavily soiled durable garments, eg tea towels, children’s clothes. 13 minutes Heavy Warm Spray/ Deep Rinse 1100 rpm 6 minutes Delicate Designed for delicate lightly soiled clothes.
WASH CYCLES – WASHSMART™ WASHER WASH TIME * WASH ACTION WASH TEMP RINSE SPIN SPEED SPIN TIME ** For normally soiled everyday cotton loads, eg t-shirts, shorts, shirts. 11 minutes Regular Warm/ Cold Spray/ Deep Rinse 1000 rpm 6 minutes Recommended cycle for heavily soiled durable garments, eg tea towels, children’s clothes. 13 minutes Heavy Warm Spray/ Deep Rinse 1000 rpm 6 minutes Delicate Designed for delicate lightly soiled clothes.
WASH CYCLES – QUICKSMART™ WASHER WASH TIME * WASH ACTION WASH TEMP RINSE SPIN SPEED SPIN TIME ** For normally soiled everyday cotton loads, eg t-shirts, shorts, shirts. 11 minutes Regular Warm Spray/ Deep Rinse 1000 rpm 6 minutes Recommended cycle for heavily soiled durable garments, eg tea towels, children’s clothes. 13 minutes Heavy Warm Spray/ Deep Rinse 1000 rpm 6 minutes Delicate Designed for delicate lightly soiled clothes.
WASH OPTIONS Water Level Auto water level (not available on QuickSmart™ washer) Your washer has the ability to automatically select the most efficient water level for the load. 1 Place your clothes in the washer. 2 Select the wash cycle (and select ‘Auto’ water level if not automatically selected). . The washer will automatically fill to the correct water level for the load, for both phases of the wash.
WASH OPTIONS Wash Temp WashSmart™ Eco washer and WashSmart™ washer offer 5 wash temperatures, and an additional setting, ‘Controlled Cold’. The wash temperature selected is used in the detergent activating part of the wash. If Eco-Active™ is ‘On’ the temperature will be colder for the second part of the wash. When Eco-Active™ ‘Off’ is selected, the bowl will fill with the wash temperature selected.
WASH OPTIONS Options Note: in some instances it is possible to select multiple options on one cycle. Soak (WashSmart™ Eco washer and WashSmart™ washer only) Use the ‘Soak’ option to soak clothes during the agitation wash phase. Ensure items are colourfast before using ‘Soak’. When you select ‘Soak’ your washer will soak for a period of 2 hours before completing ‘Rinse’ and ‘Spin’. During ‘Soak’ your washer will agitate for a few seconds every minute.
WASH OPTIONS Delay Start (not available on QuickSmart™ washer) The ‘Delay Start’ option can delay the start of the wash cycle by 5 minutes up to 18 hours. This can be useful to time your washing to finish when you arrive home from work, or to start once you have finished in the shower. Simply touch the ‘More’ button to scroll through to your desired delayed start time, or to turn delay start off. Touch to confirm your selection and start the countdown.
WASH OPTIONS Washing bulky items Forcing large items into the washer may result in them being damaged during washing. Make sure there is enough room in the washer for items to move when being washed. Some items float up during the wash (eg duvets/doonas, water-proof and waterresistant items and pillows). If they sit too high they may touch stationary parts of the washer during agitate or spin.
CUSTOMISING WASH CYCLES To customise a cycle You can program your washer to remember the wash options you prefer for each wash cycle. For instance, you may want to set the ‘Regular’ cycle to default to a ‘Warm’ wash or set ‘Heavy’ cycle to include a ‘Soak’. WashSmart™ Eco washer, WashSmart™ washer and QuickSmart™ washer . 1 Touch ‘POWER’ 2 Touch and hold the wash cycle button you wish to customise eg ‘Regular’, for 3 seconds. You will hear 2 beeps and the screen will display .
CHANGING PRE-SET OPTIONS Option Adjustment mode After using your washer a number of times you may want to fine tune some of the options to suit your wash needs. There are a number of pre-set options, which can be altered: 1 The wash temperatures, including changing the ‘Cold’ wash temperature to ‘Controlled Cold’. 2 The out of balance recovery routine. 3 The number of beeps at the end of the cycle. 4 Resetting to factory default settings. To enter Option Adjustment mode .
CHANGING PRE-SET OPTIONS Adjusting your options 1 Enter Option Adjustment mode (refer to page 34). 2 The diagram below shows how the wash cycle icons relate to the options you can change. It also shows what will be displayed when you first enter Option Adjustment mode. Options you can change are accessible using the ‘Heavy’ ‘Delicate’, ‘Wool’ and ‘Regular’ cycles.
CHANGING PRE-SET OPTIONS Wash temperatures All wash temperatures can be individually adjusted if you think they are too hot or too cold. Note: the hot temperature will be the same as the hot water supply temperature. 1 Enter Option Adjustment mode (refer to page 34). 2 Select the ‘Regular’ cycle. 3 Select the wash temperature you want to adjust, eg ‘Hot’, by touching the ‘Wash Temp’ button. The digital display screen displays the current setting.
CHANGING PRE-SET OPTIONS Controlled Cold (not available on QuickSmart™ washer) If the temperature of your cold water supply is very low and you choose to do a ‘Cold’ wash, you will not get an effective wash. The ‘Controlled Cold’ option solves this problem by adding a small amount of hot water to raise the temperature of the wash to approximately 20°C. 1 Enter Option Adjustment mode (refer to page 34). 2 Select the ‘Regular’ cycle.
CHANGING PRE-SET OPTIONS Out of balance recovery routine When your washer is spinning it can sense if the wash load is out of balance. If an out of balance load is detected, the washer will stop and re-try spinning one more time. If it still senses an unbalanced load there are two options the washer can take. Automatic recovery OFF (the default setting) Your washer will stop, beep, and show in three phases on the display screen. You must redistribute the load more evenly yourself.
CHANGING PRE-SET OPTIONS End of cycle beeps The beeps signalling the end of the cycle can be increased or decreased. The default setting is 5 beeps. To modify the number of beeps sounding at the end of the cycle: 1 Enter Option Adjustment mode (refer to page 34). 2 Select the ‘Wool’ cycle. 3 WashSmart™ Eco washer and WashSmart™ washer: Touch the ‘More’ button to increase or decrease the number of beeps, or for no beeps to sound at the end of the cycle (the end of cycle beep options will scroll around).
CHANGING PRE-SET OPTIONS Factory reset You can reset your washer to the settings it left the factory with: 1 Enter Option Adjustment mode (refer to page 34). 2 Select the ‘Delicate’ cycle. . Touch and hold for 3 seconds to reset your washer to its 3 The display will show factory settings. Note: this action will reset the washer to the default settings, exit Option Adjustment mode and restart the washer in normal operating mode. Touch ‘POWER’ to exit if you do not wish to reset your washer.
CARING FOR YOUR WASHER When you have finished using your washer ●● ●● Turn off the taps to prevent the chance of flooding should a hose burst. Turn off the power at the wall. Cold water washing If you always wash with cold water, we recommend that a ‘Warm’ or ‘Hot’ wash be used at regular intervals, eg every 5th wash should be at least a warm one. Cleaning your washer Note: ensure the power is turned off at the wall before cleaning your washer.
CARING FOR YOUR WASHER Products that might damage your washer ●● ●● ●● Concentrated bleaches, laundry pre-soakers/sanitisers, stain removers and hydrocarbon solvents (eg petrol and paint thinners) can cause damage to the surfaces eg control panel, and components of your washer. Be careful when washing garments stained with solvents as they are flammable. DO NOT put them in your dryer. Use of dyes in your washer may cause staining of the plastic components.
BEFORE YOU CALL FOR SERVICE Please read the following pages before you call for service. Your washer is capable of diagnosing its own problems. If your washer gives a musical series of beeps every 5 seconds it is telling you that it has a problem which you can solve using the checklist below. Your washer sounds a musical series of beeps* every 5 seconds and displays a user warning on the screen: PROBLEM The washer is not getting any hot water.
BEFORE YOU CALL FOR SERVICE PROBLEM DISPLAYED AS WHAT TO DO The washer is out of balance. Wash load is out of balance. Ensure the washer is stationary. Manually redistribute the load. The washer has too many suds. The washer has a suds build-up (too much detergent may have been used for the amount of soil in the load). Wait for suds to dissolve (about 20 min). Rinse clothes using a deep rinse. Check the washer is level.
FAULT CODES When a continuous series of beeps is sounded, all the lights turn off on the control panel and a number appears on the display, a fault has occurred. The washer will automatically enter this mode if a fault occurs. The fault code will be displayed as a number on the digital display. To stop the sound, touch any button and perform the following steps: 1 2 3 4 5 Turn your washer off at the power point. Wait 1 minute and turn it back on. Remove your wash load. Perform a ‘Rinse’ cycle.
TROUBLESHOOTING The following is a list of problems you may encounter when using this appliance and some suggestions that may help to correct the problem. If you still have problems, please contact your Fisher & Paykel trained and supported service technician or our Customer Care Centre. Solving operating problems PROBLEM POSSIBLE CAUSES WHAT TO DO Washer not turning on. Power not switched on at the wall. Switch the power off at the wall and wait 60 seconds before turning power on again.
TROUBLESHOOTING Solving operating problems PROBLEM POSSIBLE CAUSES WHAT TO DO Spin speed sounds slower than normal. Clothes are unevenly distributed in the bowl. Washer has compensated by lowering the spin speed. The outer wash bowl may still be hot from being filled with hot water. The washer has slowed the spin speed as a protective measure. Washer may not be level. Check the washer is level and does not rock in any direction.
TROUBLESHOOTING Solving wash problems PROBLEM POSSIBLE CAUSES WHAT TO DO Creasing. Overloading of the washer. Try reducing load size. Inappropriate cycle selection. Choose ‘Delicate’ cycle as this cycle has been designed to minimise creasing. Spin speed too high. Try selecting a lower spin speed. Do not leave wet clothes to sit in the washer or laundry basket. Wash temperature too high for items. Try selecting a lower wash temperature.
TROUBLESHOOTING Solving wash problems PROBLEM POSSIBLE CAUSES WHAT TO DO Linting. Some items in load more likely to release or pick up lint. Wash lint givers (eg towels, flannelette sheets) separately from lint collectors (eg synthetic fabrics). Overloading the washer. Try reducing your load size. Not enough detergent to hold the lint in suspension. Try using more detergent. Overdrying in a dryer can cause a build-up of static electricity in synthetic fabrics and cause them to attract lint.
MANUFACTURER’S WARRANTY You automatically receive a 2 year Manufacturer’s Warranty with the purchase of this clothes washer covering parts and labour for servicing within the country of purchase. Fisher & Paykel undertakes to: Repair or, at its option, replace without cost to the owner either for material or labour any part of the product, the serial number of which appears on the product, which is found to be defective within TWO YEARS of the date of purchase.
MANUFACTURER’S WARRANTY F Repairs when the appliance has been dismantled, repaired or serviced by other than a Fisher & Paykel trained and supported service technician or the selling dealer. G Pick-up and delivery. H Transportation or travelling costs involved in the repair when the product is installed outside the Fisher & Paykel trained and supported service technician’s normal service area.
CUSTOMER CARE Before you call for service or assistance... Check the things you can do yourself. Refer to your user guide and check: 1 Your product is correctly installed. 2 You are familiar with its normal operation. 3 You have read the ‘Before you call for service’, ‘Fault codes’ and ‘Troubleshooting’ sections at the back of the book.
CUSTOMER CARE In Singapore if you need assistance…* Please call our Fisher & Paykel Service line. Phone: 6741 0777 Fax: 6547 0123 Website: www.fisherpaykel.com Postal address: 150 Ubi Avenue 4, Sunlight Building #03-01A, Singapore 408825 *If you call, write or contact us via our website please provide: your name and address, model number, serial number, date of purchase and a complete description of the problem. This information is needed in order to better respond to your request for assistance.
www.fisherpaykel.com © Fisher & Paykel Appliances 2016. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your dealer to ensure this booklet correctly describes the product currently available. NZ AU SG ROW 429337 A 03.
