FRONT LOADER WASHING MACHINE WH1160F2, WH1260F2, WH1060S1 & WH1160S1 INSTALLATION GUIDE NZ AU BI EU
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electric shock or death. • If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet box), ensure that it is positioned so that it does not come into contact with water or moisture. SUPPLIED PARTS z z z Keep all packing materials until the unit has been inspected. Inspect the product to ensure there is no shipping damage.
PRODUCT DIMENSIONS D B C FRONT PROFILE A C D PRODUCT DIMENSIONS MM A Overall height* z Min z Max 845 860 B Overall width 600 C Overall depth** 675 D Depth with door open 1080 * Exact height is dependent on foot adjustment ** Including dial and door (when closed) Actual product dimensions may vary by ± 2 mm.
CAVITY & CLEARANCE DIMENSIONS * Front panel of the product a b c b a b b b FRONT PROFILE ISOMETRIC 4 CAVITY DIMENSIONS MM CLEARANCE DIMENSIONS MM A Minimum cavity height 865 A Minimum washer door clearance to adjacent wall 355 B Minimum cavity width 640 B Minimum gap clearance to adjacent product or cabinetry* C Minimum cavity depth z Flush with front panel of the product* z In cupboard 655 715 * Applies to sides, top and rear Actual dimensions may vary by ± 2 mm.
ELECTRICAL & PLUMBING CONNECTION CONNECTION LOCATIONS / LENGTHS DRAINAGE HEIGHTS Water Hoses 1500mm 1000mm max* 600mm min Power Cord 2000mm Drain Hose 1600mm (1400 with elbow) * Recommended standpipe height is 800mm SPECIFICATIONS ELECTRICAL Supply 220 – 240 V, 50 Hz Service 10 amp circuit PLUMBING Pressure max 1 MPa (150psi) min 50 kPa (7.3psi) Flow rate at tap Min.
UNPACKING WATER SUPPLY Water supply requirements If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should fit a tempering valve. This will ensure the hot water temperature remains within safe limits. Contact your registered plumber to select and install the tempering valve. Your cold water should not exceed 35°C and your hot water should not exceed 65°C. Temperatures above these may cause the washer to fault or cause damage to the washer.
DRAINING In multi-storey apartments or any upper floor, the washer should be installed on a floor equipped with a drain. Draining must comply with local by-laws. REMOVING TRANSIT BOLTS z z Place the drain hose in a tub or standpipe The hose guide is used to hold the drain hose over the tub or standpipe. 20 mm max. 1 Flex the guide apart and pull the hose through the guide. 2 Ensure a maximum of 20mm of the hose is left exposed at the end.
REMOVING TRANSIT BOLTS LEVELLING THE WASHER It is IMPORTANT to level the washer. Having a level washer set up in its cavity will ensure best performance for spinning, minimising noise, vibrations and wear and tear on the washer. 4 Remove the 10 transit brace screws from the left and right sides, and near the centre of the top brace. Move the washer into its final position allowing for required clearances. Level the washer side to side: 1 5 Place the level on the centre front of the washer.
COMPLETE INSTALLATION z z z Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hose(s). Check the hose connections for leaks again after 24 hours. Uncoil power cord, remove and discard the plastic pin cover, and plug into wall socket. Connect the appliance to an earthed outlet protected by a fuse of suitable capacity. Test cycle 4 Wait until you see water in the bottom of the drum. 5 Press Your washer must be correctly installed before use.
SPARE PARTS INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Have the packaging and transit bolts and rods been removed? Is the washer correctly levelled, feet are extended and cabinet corners are clear of the floor? SPARE PARTS* PART NO.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2020. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
