Deluxe Quick Response Swing with Remote Control Model Number: B1637 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Tools needed for assembly: Phillips Screwdriver and Scissors (both not included).
Warnings and Caution Consumer Information Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.
Parts Note: Tighten and loosen all screws and bolt with a Phillips screwdriver. Do not over-tighten screws.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Front Legs (Longer) Remote Holder Tapered End Press Button Press Button Ribbon 3 Tapered End 1 Front Base • Using scissors, remove the ribbon connecting the remote and the holder. • Place the front base on a flat surface.
Assembly Housing Hub Hole Holder Slot Front Leg Press Buttons Motor Housing Front Legs 7 5 • Position the housing so that the hub is inward. • While pressing the button on the top of a front leg, insert it into the housing slot, as shown. Push the front leg until the button “snaps” into the hole in the housing. • Repeat this procedure to assemble the motor housing to the other front leg. • Pull the front legs down to be sure they are secure in the housings.
Assembly Pull Up Pull Up Pull Rear Leg Pull Rear Leg Rear Legs 11 9 Rear Base • While standing on the rear base, pull the rear legs up. They should remain secured to the rear base. If you can remove the rear legs, you have not assembled them correctly to the rear base. Reread and repeat assembly step 10. • Set the frame assembly aside for Assembly step 21. • Pull both rear legs out until they “snap” into place.
Assembly M4 Lock Nut Rounded Side Bracket Grooves Shown Actual Size Tall End Lock Nut Seat Tubes Bottom Edge of Seat Hexagonal Opening 13 • Position the bracket so that the tall end is toward the bottom edge of the seat. Hint: The M4 lock nuts have been assembled to the bracket at the factory. During shipment of this product, they may have fallen out. Check to be sure there is a lock nut in each hexagonal opening on the bracket.
Assembly “Snap” in Place Seat Wire is Through Hole in Seat Wire Cap Seat Wire Slots Seat Wire Caps 17 19 • Lift the seat tubes slightly. • With the seat wire hanging down, insert the ends of the seat wire through the slots in the seat, as shown. • Press to “snap” the seat wire caps into place.
Assembly Frame Hub Slot Push Button Pad Swing Tube Front of Seat Slot Waist Belts 21 Curved Front Base 23 • Position the seat assembly so that the front of the seat is toward the curved front base. • While pressing the buttons on the swing tubes, insert them into the frame hubs. Push the swing tubes up until the buttons “snap” into the hole in the frame hubs. • Push down on the seat to be sure the seat is secured in both frame hubs. • Fit the pocket on the back of the pad onto the seat back.
Assembly Assembly Elastic Loop Elastic Loop 27 #8 x 13/8” Screw - 4 Shown Actual Size 25 • Turn the assembly over. Insert four #8 x 13/8" screws through the bottom of the lights ‘n sounds tray and into the mirror base. Tighten the screws. Assembly is now complete. • Fit the bottom edge of the pad around the bottom edge of the seat. • Hook the elastic loops on each side of the pad to the peg on the back of the accessory bins. Battery Installation Hint: When swinging, sound or power L.E.D.
Battery Installation Battery Safety Information 1.5V x 3 “AAA” (LR03) (Remote) 1.5V x 3 “AA” (LR6) (Lights 'n Sounds Tray) Battery Compartment Door 1.5V x 4 “D” (LR20) (Swing) Lights ‘n Sounds Tray • Locate the battery compartment door on the bottom of the lights ‘n sounds tray. • Loosen the screw in the battery compartment door. Lift to remove the battery compartment door. • Insert three “AA” (LR6) alkaline batteries as indicated inside the battery compartment.
Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. WARNING B • To prevent serious injury or death from falls and being strangled in the restraint system: - Always use the restraint system. Never rely on the tray to restrain child.
Adjusting the Seat Attaching the Sound ‘n Lights Tray Cat Dog Sound ‘n Lights Tray Semi-Recline Upright Bar Tray Recline • Fit the sound ‘n lights tray to the tray, as shown. • Baby activates sounds and lights by pulling on the dog or cat; or rolling the bar. Adjust the seat angle in any of three positions: Upright, Semi-Recline or Recline. To adjust the seat angle: • Push down on the seat back to position the seat wire in the desired groove in the bracket for Upright, Semi-Recline or Recline.
Swinging IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs less than 24 lbs., but is really active and appears to be able to climb out of the swing, immediately discontinue its use. Dome Hint: The swing will operate without use of the remote. Simply slide the power switch to on . Dome Hint: Make sure the dome on the remote and the dome on the swing are within 20 feet of each other, in a direct line and free of obstacles. Power L.E.D. • Slide the power switch to on .
Storage Care The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, tray and sound ‘n lights tray may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the sound ‘n lights tray. Press Buttons Upper Pad Pocket Elastic Loops Lower Pad Pocket Elastic Loops Clips Restraint Belts • Fit the bottom of the remote into the cupped portion of the holder.
For Best Results • Make sure the remote is no further away than 20 feet from the swing. • Make sure the remote and the swing are in a direct line and there are no obstacles between them. • In the unlikely event that use of the remote interferes with normal use of other remote controlled equipment, such as televisions and stereos, or use of other electric or battery powered appliances interfere with operation of the swing, do not use both appliances at the same time.