DYM74 Keep this instruction sheet for future reference, as it contains important information. Requires three AA (LR6) alkaline batteries (not included). Adult assembly is required. Tool required for assembly and battery installation: Phillips screwdriver (not included). Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy. fisher-price.
Assembled Parts Wheel Side Roof Front End Refrigerator Door Recycle Bin Counter (The battery compartment is on the underside of the counter. See Battery Installation section for instructions about installing batteries.) 3 Roof Supports Side Wall Steering Wheel Steering Wheel Retainer Base M3,5 x 19 mm Screw -18 Dash Shown Actual Size Tighten and loosen all screws with a Phillips screwdriver.
Assembly Steering Wheel Retainer CAUTION This package contains small parts. For adult assembly only. Base Front End Steering Wheel 3 • First, fit the steering wheel into the hole in the dash. • Then, fit the steering wheel retainer into the end of the steering wheel. • Insert a screw into the steering wheel retainer and tighten. 1 Front End • Turn the front end over. • Fit the base to the front end. • Insert two screws into the base and tighten. • Turn the front end upright.
Assembly Recycle Bin 7 OUTSIDE VIEW • Insert the tabs on the recycle bin into the slots in the other side of the side wall. • Push near each tab to “snap” into place. 5 • Insert a screw into each end of the dash and tighten. Refrigerator Door 8 • Fit the side wall assembly to the front end. Side Wall 6 INSIDE VIEW • Fit the refrigerator door to the side wall. • Insert two screws into the refrigerator door and tighten.
Assembly Counter Wheel 9 11 • Fit the wheel to the assembly. • Fit the slots in the underside of the counter to the tabs on the top side of the assembly. • Push near each tab to “snap” the counter in place. Roof Support 10 Roof Support INSIDE VIEW • From inside the assembly, insert and tighten six screws to attach the wheel. 12 • “Snap” the roof supports to the front end of the assembly. Hint: The roof supports are designed to fit the assembly one way.
Assembly Front Roof Side Roof 13 15 • “Snap” the front roof to the roof supports. Hint: The front roof is designed to fit the roof supports one way. If it does not seem to fit, turn it around and try again! • Fit the side roof to the front roof and the roof support. • Insert two screws into the side roof and tighten. Roof Support 14 • Slide the bottom edge of the remaining roof support between the cash register and the speaker. • Push the roof support to “snap” into place.
Battery Installation Protect the environment by not disposing of this product or any batteries with household waste. This symbol indicates that this product shall not be treated as household waste. Check your local authority for recycling advice and facilities. 1,5V x 3 AA (LR6) For longer life, use alkaline batteries. Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product.
Decoration Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the toy.
Servin’ up a truck load of fun! • Slide the power/volume switch on the cash register to ON with low volume, ON with high volume or OFF. • If this toy begins to operate erratically, you may need to reset the electronics. Slide the power/volume switch off and back on. Press the faucet • Slide the Smart Stages™ mode switch to: Learn - With each press or push, listen for objects identified, songs, fun phrases and sound effects. Engage - Listen to prompts to find different shapes, sizes, numbers and foods.
Consumer Information FCC STATEMENT (UNITED STATES ONLY) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.