L E A R N I N G ™ S N R E P A T T Infant-to-Toddler Rocker Toddler Seat Infant Seat Model Number: G5911 WARNING IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Please keep this instruction sheet, as it contains important information. Use the upright position only when your child has developed enough upper body control to sit without leaning forward. Always use the restraint until your child is able to climb in and out of the chair unassisted. Adult assembly is required.
Warning Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. The kickstand is packaged within the pad at the factory. Before beginning assembly, please remove kickstand from the pad. WARNING To prevent serious injury or death: • It is dangerous to use this product on an elevated surface. • Never use on a soft surface (bed, sofa, cushion) since product can tip over and cause suffocation in soft surfaces.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. #8 x 1.9 cm (3/4") Screw Shown Actual Size Cross Brace CAUTION This package contains small parts in its unassembled state. Adult assembly is required.
Assembly Side Rail Side Rail Hole Front Tube Side Rail Front Tube 4 Vibrations Unit 5 Side Rail Hole • Locate the hole in each side rail. • With the vibrations unit facing forward, fit the front tube to the side rails, as shown. Hold the front tube in place and proceed to step 5. • Insert a #8 x 3 cm (11/8") screw through the outside of each side rail and into the ends of the front tube.
Assembly Retainer with Lock Nut Kickstand Press Tab Press Tab 6 • Fit a retainer with lock nut onto the end of the screw and to the inside of a side rail. Rounded Side 7 Receptacles M4 Lock Nut - 2 (Inside Retainer) Shown Actual Size • Position the assembly face down, as shown. • While pressing the tab on each end of the kickstand, insert the kickstand into the receptacle in each side rail, as shown. • Push the kickstand into the receptacles until the tabs “snap” into place.
Assembly Pad Pad Slot Press Seat Back Seat Back Tube 8 • Turn the assembly upright. • Fit the upper pocket on the pad onto the seat back tube. • Fasten the pad buckles around each side rail. Hardboard 9 Side Rail • Turn the hardboard over and insert it into the slot in the front Pad edge of the pad. Buckles • Fasten the pad buckles on the front edge of the pad and underneath the seat. Make sure you hear a “snap” on both sides. • Press the fasteners together in the seat back portion of the pad.
Battery Installation Battery Safety Information + 1.5V LR20 "D" – SHOWN ACTUAL SIZE Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product.
Set-Up & Use Securing Your Infant IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. WARNING To prevent serious injury or death: • Always use the restraint until child is able to climb in and out of the chair unassisted. • It is dangerous to use this product on an elevated surface.
Securing Your Infant Anchored End Toys Anchored End Strap B Strap Strap B Toy Free End 3 Tighten Toy Free End Loosen To tighten the belts: • Feed the anchored end of the restraint belt up through the buckle to form a loop . • Pull the free end of the restraint belt B . • Repeat this procedure to tighten the other restraint belt. To loosen the belts: • Feed the free end of the restraint belt up through the buckle to form a loop . Enlarge the loop by pulling on the end of the loop toward the buckle.
Calming Vibrations Toy Bar Toy Bar Plug Plug 6 Toys Power Switch • Make sure your child is properly secured in the seat. • Slide the power switch to the on position for calming vibrations. • Slide the power switch to the off position to turn vibrations off. 5 • Fit the plugs on each end of the toy bar into the sockets in each side rail. • Fit the toy bar straps through the slot in the toy rings. Fasten the straps. • Or, attach the toys to the pad straps (see Step 4).
Kickstand Storing the Restraint System for Toddler Use Small Slot Small Slot 7 8 Kickstand • Rotate the kickstand out. • Push down on the seat bottom to be sure the kickstand is in position. Large Slot • Insert the restraint belts back through the small slots in the pad. • Insert the restraint pad down through the large slot in the pad. 9 • Turn the rocker face down. • Tuck the ends of the restraint pad underneath the buckles, as shown.
Care The frame, pad toy bar and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.