User Manual

ManualsBrandsFisher-Price ManualsBaby Floor SeatsSit-Me-Up Floor Seat with Tray

GBL17

Placing and Removing Baby

• Place the assembled product on the floor.

• Kneel or stand behind the seat and fit or remove baby’s

legs into or from the leg openings in the seat pad.

Carefully lower or lift baby into or out of the seat.

Sentar y sacar al bebé

• Poner el producto ensamblado sobre el piso.

• Arrodillarse o pararse detrás de la silla y meter o sacar las

piernas del bebé en/de los orificios de pierna del colchón.

Sentar o sacar cuidadosamente al bebé en/de la silla.

IMPORTANT! Keep these

instructions for future reference.

• Please read these instructions

before assembly and use of

this product.

• Adult assembly is required.

No tools are required

for assembly.

¡IMPORTANTE! Guardar estas

instrucciones para futura referencia.

• Leer estas instrucciones antes de

ensamblar y usar este producto.

• Requiere montaje por un

adulto. No es necesario usar

herramientas para el montaje.

fisher-price.com

Summary of content (8 pages)

PAGE 1
GBL17 IMPORTANT! Keep these instructions for future reference. • Please read these instructions before assembly and use of this product. • Adult assembly is required. No tools are required for assembly. ¡IMPORTANTE! Guardar estas instrucciones para futura referencia. • Leer estas instrucciones antes de ensamblar y usar este producto. • Requiere montaje por un adulto. No es necesario usar herramientas para el montaje. Placing and Removing Baby • Place the assembled product on the floor.
PAGE 2
Consumer Information Información al consumidor WARNING To prevent serious injury or death: • Fall Hazard – Never use on any elevated surface, since child’s movement may cause the product to slide or tip over. Use only on a floor. • Suffocation Hazard – Never use on a soft surface (bed, sofa, cushion), since the product can tip over and cause suffocation in soft surfaces. • Never leave child unattended. Always keep child in view while in product. • Never use near steps.
PAGE 3
Assembled Parts Piezas ensambladas Front Base (2 pieces) Base delantera (2 piezas) Rear Base (2 pieces) Base trasera (2 piezas) Seat Ring Aro del asiento Pad P d Colchón 2 Frames 2 armazones 2 Caps 2 tapones IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. Do not use the product if any parts are missing, damaged or broken. Do not use accessories or replacement parts other than those approved by the manufacturer.
PAGE 4
Assembly Montaje 1. 3. • “Snap” the front base pieces together. • Ajustar las piezas de la base delantera. • “Snap” the rear base pieces together. Hub Button Out Botón de conexión hacia afuera • Ajustar las piezas de la base trasera. Hub Button Out Botón de conexión hacia afuera 2. 4. • Position the frames with the hub buttons facing out. • Slide the frames into the sockets in the front base. Push to “snap” each into place. Hint: The frames and the front base are designed to fit one way.
PAGE 5
Assembly Montaje PUSH EMPUJAR PUSH EMPUJAR 7. 5 5. • Push the frame near a seat peg to “snap” the seat ring into place. Hint: If you cannot “snap” the parts into place, you may have assembled the seat ring backwards. Remove the seat ring from the frames and turn it around so that the wide, flat side is toward the front base. Then, repeat this assembly step. • Lift the frames until each “snaps” into place. • Subir los armazones hasta que cada uno se ajuste en su lugar.
PAGE 6
Assembly Montaje 11. 9. • Insert and “snap” the pegs on the pad into the holes in the front base. Pad Pegs Clavijas del colchón • Insertar y ajustar las clavijas del colchón en los orificios de la base delantera. • Fit the end of the pad with the pegs down through the seat ring. • Introducir el extremo del colchón con las clavijas en el aro del asiento. 12. 10. • Before first time use, wash the tray thoroughly with soap and water. • The tray is not microwave safe.
PAGE 7
Opening the Frame Abrir el armazón Folding the Frame Doblar el armazón Sockets Conexiones • Lift the frames until each “snaps” into place. Push down on the seat ring to be sure the frame is open. 1. • Subir los armazones hasta que cada uno se ajuste en su lugar. Presionar hacia abajo el aro del asiento para asegurarse de que el armazón esté abierto. • Fit the posts on the tray to the underside of the frame sockets for storage.
PAGE 8
Care Mantenimiento UNITED STATES 1-800-432-5437. Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052. Hearing-impaired consumers: 1-800-382-7470. MÉXICO Importado y distribuido por Mattel de México, S.A. de C.V., Miguel de Cervantes Saavedra No. 193, Pisos 10 y 11, Col. Granada, Delegación Miguel Hidalgo, C.P. 11520, México, Ciudad de México. R.F.C. MME-920701-NB3. Tels.: 59-05-51-00 Ext. 5206 ó 01-800-463-59-89. CHILE Mattel Chile, S.A., Avenida Américo Vespucio 501-B, Quilicura, Santiago. Tel.