H7185 Swing (Seat moves front to back) Cradle (Seat moves side to side) WARNING IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. www.fisher-price.co.
Consumer Information • Please read these instructions before use of this swing. • Adult assembly is required. • Tools needed for assembly: Allen Wrench (included) and Phillips Screwdriver (not included). • Requires four LR20 (“D”) alkaline batteries for operation (not included). • Maximum Weight Limit: 9 kg (20 lbs). IMPORTANT! If your child weighs less than 9 kg (20 lbs), but is really active and appears to be able to climb out of the swing, immediately discontinue its use.
Parts Motorized Frame Allen Wrench Fabric Panel Tray 4 Toys (toys may be different) Pad with Headrest Lower Seat Tube 2 Upper Legs Seat with Restraint System 2 Lower Legs 2 Feet Note: Tighten the screws with the enclosed Allen wrench.
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Button Holes Up Foot Lower Leg Upper Legs 3 1 • Position the fabric panel with the button holes up. • Position the legs so that the feet are away from you. • Slide the fabric panel onto the upper legs.
Assembly Ruffle Motorized Frame L Seat R Elbow Foot 5 Button Slot Tube Crotch Belt Hole Red Dot • Locate the R and L on the underside of each elbow foot. The R indicates the right leg. The L indicates the left leg. • While pressing the upper button on the right leg, fit it into the tube in the motorized frame. Make sure the upper button on the right leg “snaps” into the hole in the tube. • Repeat this procedure to assemble the left leg to the motorized frame.
Assembly Waist Belts Seat Tray Pad 11 Slots Slot • Insert the tray tabs into the slots in each side of the seat. 9 • Turn the seat upright. • Fold the top of the pad down. Insert the waist belts through the slots in the pad. Make sure the waist belts are not twisted. Lower Seat Tube Short Tube 12 • Fit the lower seat tube into the short tube on the seat back. 10 • Fit the pad edges around the rim of the seat.
Assembly Rounded Side Rounded Side 13 • First, fit an M5 lock nut into an opening in the short tube. Make sure the rounded side of the lock nut faces out. • Next, insert an M5 x 30 mm screw through the opening in the opposite side of the short tube. Fully tighten the screw with the Allen wrench. 15 • First, fit an M5 lock nut into an opening in the upper seat tube. Make sure the rounded side of the lock nut faces out.
Battery Installation Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product.
Set Up WARNING To prevent serious injury and/or falls and being strangled in the restraint system: • Always use restraint system. Never rely on the tray to restrain child. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg/20 lbs). • Never leave child unattended. • It is dangerous to use this product on an elevated surface. Waist Belt Waist Belt Crotch Belt 2 Restraint Belts • Place your child in the seat.
Set Up PRESS Seat Tube Button Seat Tube Tray TURN Slot 6 Using the Tray • Fit the tabs on the tray into the slots in the sides of the seat. • To remove the tray, pull one edge of the tray out and lift. Button Cradle Button Swing 4 You can adjust the motion of the swing: side to side or front to back. • Press the seat tube button to unlock the seat tube. • Rotate the seat tube to the desired position.
Swing, Waterglobe and Mobile Use Power Dial Swing/Waterglobe/Mobile ON Waterglobe/ Mobile ON Reset Button Mobile/ Waterglobe Switch Music/Sounds Switch Volume Dial Swing • Turn the power dial to the ON position To select waterglobe/mobile, slide switch to: Mobile Lights (Waterglobe) Mobile and Lights (Waterglobe) Mobile and Lights (Waterglobe) Off . The swing begins swinging. • Select any of six speed settings • Be sure to turn swinging OFF . when not in use.
Problems and Solutions Problem Probable Cause Solution Power is not on Turn the power dial to one of six settings. Batteries incorrectly installed Remove the batteries and replace in correct orientation, as indicated inside the battery compartment. Dead batteries Replace all four batteries with four, fresh “D” alkaline batteries. Need to start swinging motion To start swinging motion, give the seat a light push.