N9326 www.fisher-price.
Important! DANGER To prevent electric shock, do not immerse in water; wipe clean with damp cloth. WARNING To prevent strangulation with power cord, never place transmitter within reach of child. CAUTION This product cannot replace responsible adult supervision.
Important! • For proper setup and use, please read these instructions. • Please keep this instruction sheet for future reference, as it contains important information. • Transmitter operates on AC current. Receiver operates on AC current (use enclosed AC adaptor) or 3.6V NiMH rechargeable battery pack (included). • Before first time use, charge the rechargeable battery pack for four hours. • Adult assembly is required for wall mounting.
Features 6 7 2 14 9 13 10 5 1 3 12 8 4 4 Receiver AC Adaptor/Charger Transmitter Transmitter Tabletop Stand 11
Features 1 Main Power/Menu Button – Press to turn receiver main power ON; press again for the main menu; press and hold for approximately five seconds to turn main power OFF. 2 Power L.E.D. – Turns on when receiver power is ON. 3 Menu Navigation/Volume Control Button – Press up, down or side arrows to scroll through menu options. When the menu is not on the screen, press the side arrows to adjust volume.
Wall Mount Parts Wall Mount Bracket Cord Wrap Fasteners Shown Actual Size Wall Anchor – 4 #8 x 2" Screw – 4 Base Stand
Charging the Battery (Inside the Receiver) DC Input Jack IMPORTANT! Fully charge the receiver (with battery pack inside) for four hours before first-time use. Use only the included AC adaptor charger! Do not use any other adaptor charger. • Fit the AC adaptor charger pin into the DC input jack on the receiver. • Plug the AC adaptor charger into a standard wall outlet. Notes: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”.
Testing Sound/Video Reception Test transmitter transmission and receiver reception before installing the wall mount bracket and cord wrap (if used) and each time you change location of use. Power Dial Radio • Place the transmitter in the room where you intend to use it. • Point the transmitter toward the area you will be monitoring. Adjust the camera angle by rotating the top portion of the transmitter up or down. • Turn the power/volume dial ON. • Turn on a radio.
Testing Sound/Video Reception Sound Lights Main Power/Menu Select Button • Place the receiver in the room where you intend to use it. • Press the main power/menu select button on the front of the receiver to turn power ON. • Adjust the receiver location for best reception. • When sound is picked up by the receiver, the sound lights will turn on. - One or two lights indicate quieter sounds. - Three or more lights indicate louder sounds.
Transmitter Wall Mount Installation WARNING To prevent strangulation with power cord, never place transmitter within reach of child. IMPORTANT! Test the reception of the monitor before installing the wall mount bracket and cord wrap. Use the assistance of one adult to hold the transmitter against the wall in the spot you want to install it. Then, test the reception of the receiver in several locations around your house. Please refer to the Testing Sound/Video Reception section of these instructions.
Transmitter Wall Mount Installation 6 ft. • To provide the greatest viewing range, we recommend you install the wall mount bracket at least six feet from the floor. • Make sure the camera lens does not have an obstructed view of your baby. Adjust the camera up or down. • Allow adequate ventilation of the transmitter when mounted. Do not mount the transmitter above heating vents or other heat producing sources. Do not mount the transmitter where it can receive direct sunlight.
Transmitter Wall Mount Installation 1 Wall Mount Bracket • Hold the wall mount bracket against the wall in the location you want to install it. Make sure the wall mount bracket is straight. • Using a pencil, make a mark on the wall inside the upper hole and lower slot on the wall mount bracket. • Set the wall mount bracket aside. 2 • Using a ¼" drill bit, drill one hole through each pencil mark you made on the wall.
Transmitter Wall Mount Installation Wall Anchor 3 • Fit a wall anchor into each of the drilled holes. • Tap each wall anchor lightly with a hammer until the ends of each wall anchor are even with the surface of the wall. 4 • Align the holes on the wall mount bracket with the wall anchors. • Insert two screws into the holes in the wall mount bracket and tighten with a Phillips screwdriver. Do not over-tighten.
Transmitter Wall Mount Installation Wall Mount Bracket Cord Wrap 5 • Position the cord wrap against the wall, so that it is centered below the wall mount bracket and as close to the floor as possible. • Move the cord wrap approximately ½" towards the wall outlet. • Using a pencil, make a mark on the wall inside both holes in the cord wrap. • Set the cord wrap aside.
Transmitter Wall Mount Installation 6 • Using a ¼" drill bit, drill one hole through each pencil mark you made on the wall. Wall Anchor 7 • Place a wall anchor into each of the drilled holes. • Tap each wall anchor lightly with hammer until the ends of each wall anchor are even with the surface of the wall.
Transmitter Wall Mount Installation Cord Wrap 8 • Align the holes on the cord wrap with the wall anchors. • Insert two screws into the holes in the cord wrap and tighten with a Phillips screwdriver. Do not over-tighten. Transmitter Slot Base Stand Slot Wall Mount Bracket 9 • Put the transmitter into the base stand. • Fit the transmitter cord into the slot in the base stand and the wall mount bracket. • Slide the stand into the slot on the wall mount bracket.
Transmitter Wall Mount Installation 6 ft. Groove Cord Wrap 10 IMPORTANT! Make sure the cord is taught between the transmitter and cord wrap. Excess cord can form loops or extend into the crib and present a strangulation hazard. • Extend the transmitter cord straight down the wall to the cord wrap. • Wrap the transmitter cord around the cord wrap, leaving just enough to reach the wall outlet. Make sure there is no slack in the transmitter cord.
Setup/On Screen Displays Main Menu • First, turn both transmitter and receiver power ON. Then press the main power/ menu select button on the receiver to see the main menu. • Press the up, down or side arrows to scroll through menu options. As you scroll, the menu choices highlight and blink on the screen.
Setup/On Screen Displays Music Turn music off Turn music on and cycle through all five songs Select song number one Select song number two Select song number three Select song number four Select song number five Return to previous menu Exit menu If you turn the music ON the music icons will appear on the bottom of the screen.
Setup/On Screen Displays Night Light Turn night light off Turn night light on Return to previous menu Exit menu If you turn the night light on the night light icon will appear on the bottom of the screen. Voice Activated (For Nighttime Use) Video screen turns on for 30 seconds and then turns off. When baby makes noise, video screen automatically turns back on. It will remain on and turn off after 30 seconds from the last sound detected.
Setup/On Screen Displays Contrast/Brightness Press left or right side arrows to adjust contrast on the screen. Return to previous menu Exit menu Press left or right side arrows to adjust brightness on the screen.
Setup/On Screen Displays Out of Range The out of range warning will flash on the screen and you will hear a tone when the receiver is out of range or the transmitter is turned off. Battery Indicators Indicates receiver is using battery power (only on the menu screen). Indicates battery power is low (and you will hear a tone). Plug in the AC adaptor/charger to use AC power and charge the battery. Indicates receiver is charging.
Use IMPORTANT! Test the sound and video reception of the monitor before first time use and whenever you change the location of the transmitter (see Testing Sound/Video Reception section of these instructions). • Place the transmitter in the same room with child. Fit the transmitter into the tabletop base. Position the camera lens so it is facing child. For the best viewing range, the transmitter should be approximately five feet away from baby.
Use • To use AC current, unwrap and fully extend the AC adaptor cord (for best reception). Insert the AC adaptor pin into the DC input jack on the receiver and plug into a standard wall outlet. • Press the main power/menu button on the receiver to turn the power on. • Press the side menu navigation buttons to turn the receiver volume up or down . • To monitor baby without video, press the video on/off button at the top of the receiver. To turn video back on, simply press the button again.
Night Vision Mode When the light in baby’s room is too low, the transmitter will automatically switch to night vision mode. The image on the receiver screen will appear in black and white, not color.
Battery Replacement If you need to replace your NiMH rechargeable battery pack, please contact Fisher-Price® Consumer Relations at www.service.fisher-price.com or call 1-800-432-5437. • Locate the battery compartment door on the back of the receiver. • Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Remove the exhausted battery pack and dispose of it properly.
Problems & Solutions Problem No image on receiver screen Solution Press the video screen on/off button. You can also change the . The video screen automatically voice activated setting to turns on when baby makes noise. Batteries in receiver are weak or dead. Use AC adaptor as power source and to charge the battery. Transmitter camera lens is obstructed. Adjust the camera angle on the transmitter. Receiver beeps and out of range screen displays Receiver is out of range of transmitter.
Problems & Solutions Problem Solution Receiver beeps and displays low battery icon on screen Battery pack in receiver is weak or dead. Use AC adaptor as power source and to charge the battery for four hours. Transmitter power L.E.D. does not light Transmitter power is off. Turn transmitter power on. Loose power cord connection and transmitter power is off. Check transmitter power cord plug-to-outlet connection. No power to wall outlet and transmitter power is off.
FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
RSS-210 ICES-003 CNR-210 NMB-003 RSS-210 This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. ICES-003 This Class B digital apparatus complies with Canadian ICES-003.
One (1) Year Limited Warranty (United States Only) Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York 14052 warrants to the original owner that this product is free from all defects in material and workmanship when used under normal conditions for a period of one (1) year from the date of purchase. Should the product fail to perform properly, we will repair or replace it at our option, free of charge.
address only Baby Gear Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. ©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S.
