H6723 Instructions Please keep this instruction sheet for future reference, as it contains important information. Requires six “C” (LR14) and three “AAA” (LR03) alkaline batteries (not included). An adult must install batteries and set-up this system for use. Tool required for battery installation: Phillips screwdriver (not included). cluded.
Battery Installation Base Unit • Locate the battery compartment on the bottom of the base unit. • Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert six “C” (LR14) alkaline batteries, as indicated inside the battery compartment. Hint: We recommend using alkaline batteries for longer life. • Replace the battery compartment door and tighten the screws with a Phillips screwdriver. Do not over-tighten.
Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely.
Connecting Your Star Station™ to Your TV or VCR Special Effects Lenses Play/Pause Reset Power/Volume ROM Cartridge Power/Volume Rotate Effect Track Forward/Back Lens Select 4 Audio/Video Cable
• Position Star Station™ near your TV (or VCR) or on the floor in front of your TV. Important! Do not place Star Station™ on top of your TV. Keep excess cable off the floor and out of the way. 1 • Make sure the power/volume dial on Star Station™ is off. The power light should be off. • Turn your TV or VCR off. 2 • Locate the audio/video cable on the back of Star Station™.
• Insert the ROM cartridge into the slot in Star Station™. Note: Always turn Star Station™ off when inserting or removing ROM cartridges. 4 • Rotate the power/volume dial to turn power on. The power light turns on. • Turn your TV or VCR on. 5 • To find the picture transmitted on your TV screen, set your TV's or VCR's mode selector to INPUT or VIDEO IN. • Have your child stand about 4 or 5 feet from Star Station™. • Move the lens up or down until your child is visible on the TV screen.
No Image? If you do not see an image on your TV screen transmitted from Star Station™, try the following: 1. Press the channel down button on the VCR or TV and check for an INPUT channel below channel 2. 2. Use the menu system on your TV or VCR to find INPUT or SOURCE. Change to INPUT or SOURCE. 3. If you are still unable to see an image, refer to your TV or VCR's instruction manual. Hints About Lighting...
• Slide the power/volume switch on the microphone to either low or high volume. Hint: The microphone power/volume switch controls the volume of your voice. The volume dial on Star Station™ controls the overall volume. 7 • Press the play/pause button to start the music. Press again to pause. • Use the track forward and back buttons to move ahead or back through the songs on the ROM Cartridge.
• Star Station™ features five special effects lenses. • Press the lens button on the microphone to select from the five lenses. Lens Select • Press the rotate effect button to rotate the lens for different cool looks! Star Rotate Effect Clear Double Vision Color Warp Kaleidoscope Notes: • If you haven't used Star Station™ for several minutes, it “goes to sleep” and the power light goes out. Press the reset button to “wake it up.
Recording Your Performances If Star Station™ is connected to your VCR, you can record performances. Simply insert a blank tape and press record on your VCR. VCR not included. Connection to an External Music Source Star Station™ can be connected to an external music source such as a portable CD player or stereo so you can sing along to other music! 1. Turn the power/volume dial on the Star Station™ off. 2. Remove the ROM Cartridge from Star Station™. 3.
Troubleshooting Guide PROBLEM No image on the TV CAUSE SOLUTION TV or VCR is not set to proper input Press the channel down button on the VCR or TV and check for an INPUT channel below channel 2. Use the menu system on your TV or VCR to find INPUT or SOURCE. Change to INPUT or SOURCE. Consult your TV's or VCR’s instruction manual. Feedback noise Microphone is too close to speakers Stand further away from your TV speakers. Turn the volume down on your TV or stereo system.
ONE (1) YEAR LIMITED WARRANTY Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York 14052 warrants Star Station™ is free from all defects in material and workmanship when used under normal conditions for a period of one (1) year from the date of purchase. Should the product fail to perform properly, we will repair or replace it at our option, free of charge.