T4842 www.fisher-price.
IMPORTANT! DANGER To prevent electric shock, do not immerse in water; wipe clean with damp cloth. WARNING To prevent strangulation with power cord, never place transmitter within reach of child. CAUTION This product cannot replace responsible adult supervision.
IMPORTANT! IMPORTANT! Fully charge each receiver (with battery pack inside) for five hours before first-time use. • For proper setup and use, please read these instructions. • Please keep this instruction sheet for future reference, as it contains important information. • Transmitter operates on AC current. Receivers operate on AC current (use enclosed AC adaptor/chargers). or 3.6V NiMH rechargeable battery pack (inside receivers). • Adult setup is required.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Features 6 1 4 5 9 7 3 2 Back View Transmitter 15 8 16 14 17 9 12 19 18 13 11 Back View 10 2 Receivers 5
Features 1 Nightlight Button – press to turn on a soft glow. 2 Nightlights 3 Power Button and L.E.D. 4 Microphone 5 Nightlight Timer Switch - Turn on for 30 minutes of light. 6 Volume Buttons - press to turn speaker volume up or down. 7 Speaker 8 Power Button and L.E.D. 9 Reset/Pair Button - Press on the transmitter and receivers if you have signal interference. 10 Speaker 11 Sound Lights – watch these lights to see baby’s sounds. 12 Volume Buttons - press to turn transmitter volume up or down.
Charging the Battery (Inside the Receivers) IMPORTANT! Fully charge each receiver (with battery pack inside) for five hours before first-time use. • Use only the included AC adaptor/chargers! Do not use any other adaptor charger. • Fit the AC adaptor/charger pin into the DC input jack on a receiver. • Plug the AC adaptor/charger into a standard wall outlet. Notes: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”. Use the AC adaptor charger only in a wall outlet.
Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • If replacing the battery pack, insert it as indicated inside the battery compartment. • Always remove an exhausted battery pack from the product. Dispose of the battery pack safely. Do not dispose of this product in a fire. The battery pack inside may explode or leak. Contact Fisher-Price® Consumer Relations at www.service.fisher-price.
Testing Sound Reception Test transmitter and receiver reception each time you change location of use. Power Button and L.E.D. • Place the transmitter in the room where you intend to use it. • Press the transmitter power button to turn the power ON. The power L.E.D. lights.
Setup and Use NightLight Battery Indicator Nap Timer Clock Clock Set • Turn receiver power ON. • Press and hold the bottom of the nap timer/clock button to choose 12-hour or 24-hour clock format. Press the top of the nap timer/clock button to make a choice. • Press the bottom of the nap timer/clock button . The hour number on the clock will flash. Press the top of the nap timer/clock button to scroll through hour choices. • Press the bottom of the nap timer/clock button .
Testing Sound Reception Power Button and L.E.D. Range Indicator Sound Lights • Place a receiver in the room where you intend to use it. • Press the power button to turn the power ON. Wait a few seconds to see if you have a good signal. If the range indicator light blinks along with beeping, you are out of range. Move the receiver closer to the transmitter. Hint: If you’d like to use AC power, use the AC adaptor/charger. • When sound is picked up by a receiver, the sound lights turn on.
Setup and Use Nightlight Button Power Button and L.E.D. Nightlight Timer Switch • Place the transmitter in the same room with child. Point the microphone towards the crib or play area. • Unwrap and fully extend the power cord for best transmission. Plug the power cord into a standard wall outlet. Use the power cord only in a wall outlet. Do not plug into a ceiling outlet. • Press the transmitter power button to turn the power ON. The power L.E.D. will light.
Setup and Use Volume Buttons Range Indicator Sound Lights • Place a receiver where you can see and hear it. • To use AC power, unwrap and fully extend the AC adaptor/charger cord for best reception. Insert the AC adaptor/charger pin into the DC input jack on the receiver and plug into a standard wall outlet. • Press the power button to turn the power ON. Press the up and down volume buttons to adjust the volume as needed.
Problems & Solutions Problem Solution Receiver range indicator light flashes Receiver is out of range of transmitter. Move receiver closer to transmitter. and you hear beeping Note: Range varies depending on surrounding conditions such as noise levels, physical obstructions and signal interference. Transmitter power is off. Turn transmitter power on. Loose power cord connection and transmitter power is off. Check transmitter power cord plug-to-outlet connection.
FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ICES-003 NMB-003 • This Class B digital apparatus complies with Canadian ICES-003. • Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. • Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
