Model: 2050 Sit-To-Stand Desk Owner’s Manual Recommended Max Load: 25 lbs. (11.3 kgs.) VISIT OUR WEBSITE: WWW.THEFITDESK.COM OR CALL US AT 1-336-423-5029 MONDAY - FRIDAY 9 A.M. - 5 P.M. EST DISTRIBUTED BY FD PRODUCTS LLC.
TABLE OF CONTENTS Introduction............................................................1 Assembly..............................................................5 Safety Warnings / Maintenance.............................2 Operational Instructions........................................7 Customer Support..................................................3 Warranty...............................................................8 Tools / Hardware / Parts........................................
SAFETY WARNINGS - URGENT PLEASE READ THIS SECTION WE WANT YOU TO SAFELY USE THIS PRODUCT 1. Read the entire manual before assembling and using this equipment. Safe use can only be achieved if the equipment is assembled, maintained and used properly. All users of the equipment must be informed of all warnings and precautions. 2. CAUTION! Do not exceed the Maximum Listed Weight Capacity of 25 lbs. (11.3 kgs). Serious Injury or Property Damage may occur. 3.
CUSTOMER SERVICE QUESTIONS NEED HELP? CONTACT US FIRST 1-336- 423-5029 MONDAY - FRIDAY 9 A.M. - 5 P.M. EST EASY TO USE CUSTOMER TICKETING Step 1: www.thefitdesk.com Step 2: “Support” Step 3: “Submit A Support Ticket” customerservice@thefitdesk.com FOR FASTEST POSSIBLE SERVICE PLEASE HAVE AVAILABLE Model # (refer to this manual) - Serial # (located on Where is this located?) WWW.THEFITDESK.
TOOLS Estimated Assembly Time : 10 minutes AA BB AA AA. (1) 4mm Allen Wrench BB BB. (1) 5mm Allen Wrench Each FitDesk® Sit To Stand Desk comes equiped with two Allen Wrenches (AA) (BB). HARDWARE Note: Hardware and Tools not shown to actual size. DD CC CC. (2) M6 x 12 Allen Bolt EE DD. (4) M6 x 30 Allen Bolt EE. (4) M8 x 20 Allen Bolt PARTS A B C B. (1) Base A. (1) Desktop C. (1) Post D E D. (1) Basket E.
ASSEMBLY NOTE: Before assembly please check all parts carefully. B BB EE Step 1: Attach the Base (B) and the Post (C) by using the supplied 5 mm Allen Wrench (BB) to tighten the M8 x 20 Allen Bolts (EE). Figure 1 B C Note: Do not overtighten Allen Bolts. FIGURE 1 C DD DD C DD AA DD A AA FIGURE 2 Step 2: Attach the Desktop (A) and the Post (C) by using the supplied 4 mm Allen Wrench (AA) to tighten the M6 x 30 Allen Bolts (DD).
ASSEMBLY A Step 3: While the Desktop (A) is still upside down, slide the plastic ring down, insert into place. Figure 3 A FIGURE 3 Step 4: Using two M6 x 12 Allen Screws (CC) and the 4 mm Allen Wrench (AA) fasten the Basket (D) to the underside of the Desktop (A). Figure 4 CC A CC AA FIGURE 4 D E FIGURE 5 A Step 5: Insert the Cable Management Box (E) into the Desktop (A). Figure 5 Your FitDesk® Model 2050 Sit To Stand Desk is now ready to use.
OPERATIONAL INSTRUCTIONS NOTE: Before operating please read carefully HEIGHT ADJUSTMENT Step 1: To adjust the height of the Desktop (A) push handle up and hold. A A FIGURE 1 Step 2: Using both hands push down on the Desktop (A) to a desired height. Figure 2 Step 3: Using the same motion lift up the Desktop (A).
WARRANTY This limited warranty is applicable to each original end-customer (hereinafter “Customer”) purchasing the FitDesk® Model: 2050 Sit-To-Stand Desk consisting of the structural metal frame (hereinafter the “Structural Frame”) and various other non-frame components (hereinafter the “Non-Frame Parts”) sold by FD Products, LLC (hereinafter “Company”) for Customer’s own use and not for resale. The Structural Frame and Non-Frame Parts are collectively referred to herein as the “Products”. 1.
WARRANTY 1.1. IF A COMPANY PRODUCT DOES NOT CONFORM TO THESE LIMITED WARRANTIES, THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY IS, AT COMPANY’S SOLE AND EXCLUSIVE OPTION, THE (1) REPAIR OF ANY DEFECTIVE PRODUCT OR COMPONENT PART OR (2) REPLACEMENT OF ANY DEFECTIVE PRODUCT OR COMPONENT PART.
facebook.com / Fitdesk FitDesk® is a registered trademark of FD Products LLC.