Pow wer C Cage Attac A chmen nt MPORTA TANT: Read all insttructions carefully c before b ussing this product. p Retain this ownerr’s manuall for future e reference e. The speecifications s of this productt may vary y from this p photo and d, subject to o change w without notice. 2852.
STOP ARRÊT ALTO PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. If you need help with product information, assembly, or replacement parts. Please contact customer service. Email us at: Service@paradigmhw.
TABLE OF CONTENTS SERVICE-------------------------------------------------------------------- 2 LABEL PLACEMENT----------------------------------------------------- 3 PRODUCT SAFETY------------------------------------------------------ 4 ASSEMBLY PREPARATION-------------------------------------------- 5 PRODUCT DRAWING--------------------------------------------------- 6 OVERVIEW------------------------------------------------------------------ 7 HARDWARE PACK---------------------------------
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damage or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Open Daily) by below methods: For Best Service Email: Service@paradigmhw.com Website: www.paradigmhw.
LABEL PLACEMENT 3
PRODUCT SAFETY WARNING: Before using this equipment you should consult with your personal physician to see if the equipment is appropriate for you. Do not use this equipment without your physician’s approval.
ASSEMBLY PREPARATION Warning: It is highly recommend that you have assistance during the assembly of the strength equipment. 1. Tools for assembly: General tools you may needed for the assembly of the strength equipment. Metric Allen Key Set Metric Wrench Set and Adjustable Wrench Flat Screwdrivers Phillips Screwdrivers Rubber Mallet Silicone Spray Oil 2. Insert bolts into the frame as illustrated in the drawing of each of the steps. 3.
PRODUCT DRAWING 6
OVERVIEW DRAWING 7
HARDWARE PACK 8
PART LIST Part# Description Q’ty. Part# Description Q’ty. A BASE ASSEMBLY 1 27 BUTTON ALLEN BOLT M10x1.5x15L 1 B SLIDER BAR MOUNT 1 51 WASHER D11xD20x2.0 11 C UPPER PIPE ASSEMBLY 1 52 WASHER D13xD24x2.5 24 D SLIDER BAR 1 75 NYLON NUT M10 8 E SLIDER 1 76 NYLON NUT M12 12 F FOOT REST 2 158 G PULLEY PLATE 2 189 H STOPPER PLATE 1 192 I LAT PULL DOWN BAR 1 209 HANDGRIP D23x3.0x210 2 J CURL BAR 1 210 HANDGRIP D23x3.
STEP 1 1A. Slide the Base Assembly (A) underneath the Stability Beam (K-6877) and align it with the bolt holes on the bottom side of the Stability Beam (K-6877). 1B. Place and align the Slide Bar Mount (B) with the bolt holes on the top side of the Stability Beam (K-6877) 1C. Fasten the Base Assembly (A), Stability Beam (K-6877), and the Slide Bar Mount (B) together by using: 2 - (16) Hex Bolt M12x1.75x105L 4 - (52) Washer D13xD24x2.
STEP 1 Wrench 2PCS K-6877 NO.16 Hex Bolt M12x1.75x105L 2PCS NO.76 Nylon Nut M12 2PCS 11 NO.52 Washer D13xD24x2.
STEP 2 2A. Attach the two Foot Rests (F) and two Connecting Plates (K) to the Stability Beam (K-6877) by using: 4 - (7) Hex Bolt M12x1.75x80L 8 - (52) Washer D13xD24x2.5 4 - (76) Nylon Lock Nut M12 Thoroughly tighten the hardware once complete.
STEP 2 Wrench 2PCS NO.7 Hex Bolt M12x1.75x80L 4PCS NO.52 Washer D13xD24x2.5 8PCS 13 NO.
STEP 3 3A. Insert the Slider Bar (D) into the Slider Bar Mount (B) and hold the Slider Bar (D) in place. 3B. Align the bolt holes of the Stopper Plate (H) with the bolt holes at the rear of the Slider Bar Mount (B) and fasten the Stopper Plate (H), Slider Bar (D), and Slider Bar Mount (B) together by using : 2 - (22) Hex Bolt M12x1.75x75L 4 - (52) Washer D13xD24x2.5 2 - (76) Nylon Lock Nut M12 3C. Mount the Slider (E) on to the Slider Bar (D) and gently lower it to the bottom of the Slider Bar (D). 3D.
STEP 3 Wrench 2PCS NO.22 Hex Bolt M12x1.75x75L 2PCS NO.52 Washer D13xD24x2.5 4PCS 15 NO.
STEP 4 4A. Insert the Upper Pipe Assembly (C) into the Slider Bar (D) and secure it by using: 2 - (26) Hex Bolt M12x1.75x70L 4 - (52) Washer D13xD24x2.5 2 - (76) Nylon Lock Nut M12 4B. Attach the Upper Pipe Assembly (C) and one Connecting Plate (K) to the Rear Crossbeam (G-6877) by using: 2 - (16) Hex Bolt M12x1.75x105L 4 - (52) Washer D13xD24x2.5 2 - (76) Nylon Lock Nut M12 Thoroughly tighten the hardware once complete.
STEP 4 Wrench 2PCS NO.16 Hex Bolt M12x1.75x105L 2PCS NO.26 HEX BOLT M12x1.75x70L 2PCS 17 NO.76 Nylon Nut M12 4PCS NO.52 Washer D13xD24x2.
STEP 5 5A. In preparation for the installation of the pulleys in step 6 take the Upper Cable (291) and feed the smaller end into Upper Pipe Assembly (C) until it can be pulled out from the furthest hole at the opposite end of Upper Pipe Assembly (C). 5B. Pull the rest of Upper Cable (291) through and allow it to hang from the hole at the end of Upper Pipe Assembly (C). 5C. Take the Lower Cable (292) and feed the smaller end through the oval hole at the front of the Base Assembly (A). 5D.
STEP 5 19
STEP 6 6A. Install the two Wide Groove Pulleys (L) at the locations shown in the diagram AA-1 by using: 2 - (25) Hex Bolt M10x1.5x65L 4 - (51) Washer D11xD20x2.0 2 - (75) Nylon Lock Nut M10 6B. Install the five Pulleys (228) at the locations shown in the diagrams by using: 3 - (24) Hex Bolt M10x1.5x50L 2 - (25) Hex Bolt M10x1.5x65L 6 - (51) Washer D11xD20x2.0 5 - (75) Nylon Lock Nut M10 Thoroughly tighten the hardware once complete. 6C.
STEP 6 AA-1 NO.25 HEX BOLT M10x1.5x65L 4PCS Wrench 2PCS NO.24 HEX BOLT M10x1.5x50L 3PCS 21 AA-2 NO.75 NYLON NUT M10 7PCS NO.51 WASHER D11xD20x2.
STEP 7 7A. To adjust the Length of the Lower Cable (292) use the Chain (294) and an additional Hook (293) to give a comfortable length to workout with. 7B. To adjust the Length of the Upper Cable (291), change the location at which the Pulleys (228) are mounted to the Pulley Plates (G). Mounting the Pulleys (228) at the furthest holes at the ends of the Pulley Plates (G) will loosen the cable slack.
STEP 7 Hole options of the Pulley Plate (G) parts are for adjusting the slack of the cables as the cable ages. Use the Hook (293) and the loops of the Chain (294) to adjust the slack of the cable.
Optional 4mm Allen Wrench 1PC If you would like to use the available Olympic Plate Adaptors for Olympic sized plates, please follow the steps below: A. Use a 4 mm Allen key to loosen the Allen screws of the Olympic Plate Adaptors (226). B. Slide the Olympic Plate Adaptors (226) on to the two posts of Slider (E). C. To lock the two Olympic Plate Adaptors (226) in place, use a 4mm Allen key to tighten the Allen screws of the Olympic Plate Adaptor (226). D.
Optional When using standard size 1” inch plates, use the available Standard Clips. To install the Standard Clips, please follow the steps below: A. Pinch the rubber grips of Standard Clip (294). B. Slide a Standard Clip (294) on to each post of the Slider (E).
LUBRICATION D E E Lubrication The machine must be lubricated periodically. ONLY USE SILICONE OIL when lubricating the Slider Bar (D). A. Wipe the Slider Bar (D) clean using a dry cloth. Be sure to clean off any dried oil. Remove the Silicone Oil from the Manual pack and cut the lid off using a pair of scissors. B. Apply the Silicone Oil generously across the Slider Bar (D) and inside the Square Bushing (225). Move the Slider (E) up and down to spread the oil.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness guarantees to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PARTS REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.