Installation Guide

ManualsBrandsFiveStar ManualsAppliances30 Inch Dual Fuel Liquid Propane Freestanding Range, in Stainless Steel

INSTALLATION INSTRUCTIONS

PROFESSIONAL RANGE MODELS

30” DUAL FUEL, CONVECTION, SELF CLEAN WITH OPEN BURNERS**

30” NATURAL GAS MODELS

*TN275-BW

*TN275-W

**THESE MODELS ARE FIELD CONVERITBLE FOR LP/PROPANE GAS.**

30” LP/PROPANE GAS MODELS

*PN275-BW

*PN275-W

**THESE MODELS ARE FIELD CONVERTIBLE FOR NATURAL GAS.**

IF YOU HAVE QUESTIONS, CALL 800-251-7224, 8 AM TO 5 PM EASTERN TIME, OR VISIT OUR

WEBSITE, WWW.FIVESTARRANGE.COM.

Summary of content (11 pages)

PAGE 1
INSTALLATION INSTRUCTIONS PROFESSIONAL RANGE MODELS 30” DUAL FUEL, CONVECTION, SELF CLEAN WITH OPEN BURNERS** 30” NATURAL GAS MODELS *TN275-BW *TN275-W **THESE MODELS ARE FIELD CONVERITBLE FOR LP/PROPANE GAS.** 30” LP/PROPANE GAS MODELS *PN275-BW *PN275-W **THESE MODELS ARE FIELD CONVERTIBLE FOR NATURAL GAS.** IF YOU HAVE QUESTIONS, CALL 800-251-7224, 8 AM TO 5 PM EASTERN TIME, OR VISIT OUR WEBSITE, WWW.FIVESTARRANGE.COM.
PAGE 2
Installation Instructions BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local CAUTION: THESE RANGES SHOULD BE INSTALLED IN CONJUNCTION WITH A SUITABLE OVERHEAD VENT HOOD. Due to the high heat capacity of this unit, particular attention should be paid to the hood duct work installation to assure it meets local building codes. inspector's use. • IMPORTANT - Observe all governing codes and ordinances.
PAGE 3
INSTALLATION INSTRUCTIONS Please read these instructions before attempting to install this range Inspection and Unpacking Check the range carton for visible damage. If there is damage or even creases in the carton, contact the carrier, request an inspection and file the appropriate freight claim. Do not refuse shipment. Responsibility for shipping damage is with the carrier and the dealer or end user. Cut the shipping straps, then carefully lift the carton up from the range.
PAGE 4
STEP 1 REMOVE PACKAGING Before moving the range indoors:  Remove outer carton and packing material from the shipping base. The range is now ready for removal from the wooden base. STEP 2 Due to the weight of these ranges, use a dolly with soft wheels to move this range.  Lift the range onto the dolly and move indoors.  The range should be placed onto sliders to prevent damage to the floor. STEP 3 To simplify handling and to reduce the weight of the range:  Remove the grates and the burner pans.
PAGE 5
STEP 5 CONNECTING THE RANGE TO ELECTRIC WARNING: THIS APPLIANCE MUST BE CONNECTED AS SHOWN IN FIGURE 1 OR 2. IF A CORD IS UTILIZED IT MUST BE RATED AT 250 VOLTS, 40 AMPERES AND CERTIFIED FOR USE ON HOUSEHOLD RANGES.
PAGE 6
PAGE 7
STEP 7 CONNECTING THE RANGE TO GAS Because hard piping restricts movement of the range, the use of an A.G.A. certified flexible metal appliance connector is recommended unless local codes require a hardpiped connection. Never use an old connector when installing a new range. If the hard piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.
PAGE 8
STEP 8 LEVEL THE RANGE 1. Remove shipping tape from the leveling legs. 2. Carefully slide the range into position. Be careful not to damage the floor or entangle power cord and gas flexible tubing. 3. To adjust leveling legs, turn counterclockwise to raise the range; clockwise to lower. “Channel-lock” type pliers are recommended. Avoid using a pipe wrench which can scar the legs. IMPORTANT: The range should always be installed at countertop height or higher.
PAGE 9
PAGE 10
STEP 11 ASSEMBLE SURFACE BURNER COMPONENTS • Remove shipping screw from each surface burner. • Remove each surface burner. • Place drip pan in position under each burner. Locate “dimples”. • Re-install surface burners. • Install burner pans. • Install burner grates. STEP 12 SURFACE BURNER OPERATION OPEN SURFACE BURNERS • Check for proper ignition: − Push in one control knob and turn 180° counter clockwise to LITE position.
PAGE 11
STEP 15 CHECKLIST FOR OPEN BURNER INSTALLATION MAKE SURE ALL CONTROLS ARE IN THE “OFF” POSITION.