User Manual

ManualsBrandsFiveStar ManualsCooking Appliances SetsTTN0487S

INSTALLATION INSTRUCTIONS

PROFESSIONAL COOKTOP MODELS

48” GAS COOKTOP WITH OPEN BURNERS**

48” NATURAL GAS MODEL

*TN048-7

**THIS MODEL IS FIELD CONVERITBLE FOR LP/PROPANE GAS.**

48” LP/PROPANE GAS MODEL

*PN048-7

**THIS MODEL IS FIELD CONVERITBLE FOR NATURAL GAS.**

IF YOU HAVE QUESTIONS, CALL 800-251-7224, 8 AM TO 5 PM EASTERN TIME, OR VISIT OUR

WEBSITE, WWW.FIVESTARRANGE.COM.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS PROFESSIONAL COOKTOP MODELS 48” GAS COOKTOP WITH OPEN BURNERS** 48” NATURAL GAS MODEL *TN048-7 **THIS MODEL IS FIELD CONVERITBLE FOR LP/PROPANE GAS.** 48” LP/PROPANE GAS MODEL *PN048-7 **THIS MODEL IS FIELD CONVERITBLE FOR NATURAL GAS.** IF YOU HAVE QUESTIONS, CALL 800-251-7224, 8 AM TO 5 PM EASTERN TIME, OR VISIT OUR WEBSITE, WWW.FIVESTARRANGE.COM.
PAGE 2
Installation Instructions BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local inspector's use. • IMPORTANT - Observe all governing codes and ordinances. CAUTION: COOKTOPS SHOULD BE INSTALLED IN CONJUNCTION WITH A SUITABLE OVERHEAD VENT HOOD. Due to the high heat capacity of this unit, particular attention should be paid to the hood and duct work installation to assure it meets local building codes.
PAGE 3
INSTALLATION INSTRUCTIONS Please read these instructions before attempting to install this cooktop. Inspection and Unpacking Check the cooktop carton for visible damage. If there is damage or even creases in the carton, contact the carrier, request an inspection and file the appropriate freight claim. Do not refuse shipment. Responsibility for shipping damage is with the carrier and the dealer or end user. Cut the shipping straps, then carefully lift the carton up from the cooktop.
PAGE 4
STEP 1 REMOVE PACKAGING Before moving the cooktop indoors: Remove outer carton and packing material from the shipping base. The cooktop is now ready for removal from the wooden base. STEP 2 To simplify handling and to reduce the weight of the cooktop: Remove the grates and the burner pans. Remove griddle/grill and housing. STEP 3 POSITIONING/LEVELING Built-in cooktops must be level to obtain proper cooking results.
PAGE 5
STEP 4 ELECTRIC CONNECTION This cooktop must be supplied with 120 volt, 60 Hz. and connected to an individual, properly grounded branch circuit protected by a 5 amp circuit breaker or time delay fuse. The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong grounding wall receptacle to minimize the possibility of shock hazard from this appliance.
PAGE 6
STEP 5 CONNECTING THE COOKTOP TO GAS Because hard piping restricts movement of the cooktop, the use of an A.G.A. certified flexible metal appliance connector is recommended unless local codes require a hardpiped connection. Never use an old connector when installing a new product. If the hard piping method is used, you must carefully align the pipe; the cooktop cannot be moved after the connection is made.
PAGE 7
STEP 6 ASSEMBLE SURFACE BURNER COMPONENTS • Remove shipping screw from each surface burner. • Remove each surface burner. • Place drip pan in position under each burner. Locate “dimples”. • Re-install surface burners. • Install burner pans. • Install burner grates. STEP 7 GAS & ELECTRIC SUPPLY • Turn gas supply “on”. • Turn electric supply “on”. STEP 8 SURFACE BURNER OPERATION OPEN SURFACE BURNERS • Check for proper ignition: − Push in one control knob and turn 180° counter clockwise to LITE position.
PAGE 8
STEP 9 CHECKLIST FOR OPEN BURNER INSTALLATION ฀ MAKE SURE ALL CONTROLS ARE IN THE “OFF” POSITION.