PAD-1000 Wireless Broadband Modem Dimenstions: 5.32" long x 3.37" wide x 1.
Copyright © 2004 Flarion Technologies, Inc. All rights reserved. Safety and Hazards Remember to follow any special regulations in force in any area and always power down the Wireless Broadband Modem whenever radio transmitting devices are forbidden to use it, or when it may cause interference or danger. When connecting the Wireless Broadband Modem to another device, read its user’s guide for detailed safety instructions.
PAD-1000 Table of Contents Wireless Broadband Modem BASICS…………………………………............................. 3 About the Wireless Broadband Modem ....................................................................... 3 About the Wireless Broadband Modem software........................................................ 3 What is the Mobility Manager?..................................................................................... 3 Package contents................................................................
PAD-1000 About Flarion Flarion Technologies is mobilizing the Internet with its innovative mobile communications system - FLASH-OFDM®. The system enables licensed mobile operators to profitably offer voice and data broadband services. For mobile operators, Flarion's technology has the lowest cost per broadband subscriber as compared to any mobile system in the world.
PAD-1000 Wireless Broadband Modem Basics About the Wireless Broadband Modem The Wireless Broadband Modem is a wireless desktop modem that provides always-on access to the Wireless Broadband network. The modem is designed for plug-and-play compatibility with desktop PCs, notebook PCs, and other consumer electronic devices (gaming consoles, web tablets, etc) that have standard Ethernet or USB connections. Users can utilize the Wireless Broadband Modem in stationary or mobile environments.
PAD-1000 Package contents • Wireless Broadband Modem (with internal battery) • Antenna • Installation CD-ROM, including this User Guide • Power Adapter • Ethernet Cable • USB Cable • Quick Start Guide Note: Both the Ethernet and USB cables that are provided act as interfaces between your computer and the cT-1000 device. The Ethernet cable is the one that looks similar to (thicker than) a standard telephone line. The power adapter is necessary to charge your mT-1000 device.
PAD-1000 1. Installation and Configuration Getting started General Warning - Do not connect the Wireless Broadband Modem to your PC before the Mobility Manager software has been installed (Installation CD-ROM). Otherwise, the application will not work. BATTERY NOTE: It is recommended that you charge the Wireless Broadband Modem for a minimum of twelve hours before first use, particularly if you plan on using it in a portable environment. Otherwise, the battery will not perform as well.
PAD-1000 3. The CD Launcher Menu should appear. If the Menu does not appear, see box below. 4. In the CD launcher menu, click “Install Software” 5. Select the option for your operating system to launch the Mobility Manager wizard. If the Mobility Manager wizard dialog box does not appear (it may be hidden behind the CD launcher menu), press the Esc key; it should now be visible.
PAD-1000 Step 2: Connect the Wireless Broadband Modem to host PC After successfully installing the software, connect the modem to your PC by completing the following steps: 1. Click (PRESS FIRMLY) the antenna into the circular connector on the side of the modem (opposite side of Ethernet and USB socket). You should hear a click when inserted correctly. Keep the antenna pointed up to ensure its optimum performance. Antenna Figure 2, Attachment of the antenna 2.
PAD-1000 ü STEP 2 COMPLETE (ETHERNET ONLY)- YOUR MODEM IS NOW READY TO CONNECT, BUT ONLY THROUGH THE ETHERNET CABLE. IF YOU WISH TO CONNECT THROUGH THE USB CABLE, ADDITIONAL STEPS ARE REQUIRED (SEE BELOW). For USB Connections Only (Ethernet Connections do not apply) When you first connect using the USB cable, the “Found New Hardware" message appears as Windows attempts to install the appropriate Drivers (this is not applicable for Ethernet connections).
PAD-1000 Figure 5, Digital Signature Not Found (2000) 2. From the "Completing the Found New Hardware Wizard" page, click Finish. The driver installation is now complete for Windows 2000 users. If prompted, restart your PC. ü STEP 2 COMPLETE (USB)- YOUR MODEM IS NOW READY TO CONNECT THROUGH THE USB CABLE. Step 3: Connecting to the Wireless Broadband network When you press the Wireless Broadband Modem power button, and the Ethernet or USB cable is attached correctly, the following will occur: 1.
PAD-1000 Transmit/ Receive Indicators: These will illuminate when data is being transmitted (sent) or received. Signal Indicators Transmit/Receive/ARQ Indicators Power (PWR) Indicator Power Button Signal Indicators: Will show 1-4 indicators illuminated, depending on the signal strength. The higher the strength, the more indicators are shown. If device cannot locate the network, the indicators will “scan” from left to right. Power Indicator This will illuminate when device is turned on.
PAD-1000 2. Using the Modem The Wireless Broadband Modem can be used in stationary or mobile environments. Once the software has been installed, simply plug the modem into your laptop or desktop PC using the Ethernet or USB cable that is included in your packaging. It is recommended that you charge the modem for three hours on an ongoing basis if you consistently require portability. To charge the modem, simply connect it to a power outlet.
PAD-1000 Connection Status and Connection Time The Mobility Manager will indicate either “Connected” or “Searching”, depending on the Connection Status of your Wireless Broadband Modem. The Connection Time indicator will show you how long you have been connected to the Wireless Broadband network (for that particular session only). When you end the session (turn off the computer, unplug the device, or disable the program), this value is reset to zero.
PAD-1000 Power When the modem is plugged into an electrical outlet, a lightning bolt icon appears in the bottom right corner of the Mobility Manager. Your battery is being charged at the point. When the modem is using battery power, the battery icon appears instead. You can use this to monitor your battery power. Close, Exit, and End Session • To Close the Mobility Manager window, click the X in the top right corner. Note that this does not end the session (break the connection).
PAD-1000 Uninstalling the Mobility Manager software To uninstall the Mobility Manager software, follow these steps: 1. Click the “My Computer” icon on your desktop. 2. Click the “Control Panel” icon in your “My Computer” folder. 3. Click the “Add/Remove Programs” icon. 4. Scroll down to “Mobility Manager” and click it. Then click on “Change/Remove.” Follow instructions. Click “Next” and then “Finish.” The software is now uninstalled.
PAD-1000 3. Troubleshooting Problems, causes and suggestions When properly installed and used, the modem is very reliable. Problems that arise are likely to be because: • Wireless Broadband coverage is not available. • the modem is not compatible with the operating system in your PC. • other devices are using the system resources that are required for the modem to function. • the wrong driver has been installed.
PAD-1000 Modem problems Possible Causes Suggestions Mobility Manager displays the message: “Searching” You are outside the network coverage area. Your antenna is not attached. Contact Customer Care to verify that you are in coverage area. Move to another location or reposition your antenna.
PAD-1000 4.
PAD-1000 5. Regulatory Information Manufacturer’s Federal Communication Commission Declaration of Conformity statement Model: Wireless Broadband Modem Wireless Broadband Modem FCC Certification Number: QZX99163001 Manufacturer: Flarion Technologies, Inc.135 Route 202/206 South Bedminster One Bedminster, NJ 07921 This device complies with FCC Rules Part 15 and Part 24. The modem has been tested with a typical laptop.
