Installation Guide

ManualsBrandsFlashlogic ManualsAutomotiveGM Keyless Upgrade Remote Start System

REVISION DATE

20170427

DOCUMENT NUMBER

NOTICE The manufacturer will accept no responsability for any electrical

damage resulting from improper installation of this product, be that either

damage to the vehicle itself or to the installed device. This device must be in-

stalled by a certiﬁed technician. Please review the Installation Guide carefully

before beginning any work.

BEFORE INSTALLATION

1- Connect module to computer

2- Login to Weblink account

3- Flash ﬁrmware to module (module is not preloaded with ﬁrmware)

4- Use accessories accordingly (accessories are sold separately)

U.S. Patent No. 8,856,780

INSTALL GUIDE

FLCGMRSGM10FLRSGM10EN

HARDWARE

FLRSGM10

ACCESSORIES

FLPROG REQUIRED

FLRF1/2/4 OPTIONAL

CARLINK ASCL2 OPTIONAL

FIRMWARE

FLCGMRSGM10FLRSGM10

38693

Summary of content (20 pages)

PAGE 1
INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN DOCUMENT NUMBER 38693 REVISION DATE 20170427 FIRMWARE FLC-GM(RS)-GM10-[FLRSGM10] HARDWARE FLRSGM10 ACCESSORIES FLPROG (REQUIRED) FLRF1/2/4 (OPTIONAL) CARLINK ASCL2 (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician.
PAGE 2
PAGE 2 OF 20 DOC.
PAGE 3
PAGE 3 OF 20 DOC.
PAGE 4
PAGE 4 OF 20 DOC.
PAGE 5
PAGE 5 OF 20 DOC.: #38693 • 20170427 COMPATIBLE ACCESSORIES - 1 OF 1 RF KIT (accessories sold separately) FLRF1/2/4 RF KIT (NC) MODULE RF PORT ANTENNA TELEMATIC KIT (accessories sold separately) CARLINK FLHRNTM MODULE TELEMATIC PORT (NC) TELEMATIC KIT (accessories sold separately) FLHRNTM PN 4120260 MODULE TELEMATIC PORT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VEHICLE OBDII PORT (NC) U.S. Patent No. 8,856,780 Automotive Data Solutions Inc.
PAGE 6
PAGE 6 OF 20 DOC.: #38693 • 20170427 Escalade / ESV / Hybrid Escalade EXT Avalanche Caprice Equinox Express CHEVROLET Impala Impala limited Monte Carlo Silverado / Hybrid 07-14 07-13 07-13 11-13 07-09 08-17 06-13 13-16 06-09 07-13 POLARITY MODULE LOCATION COMPONENT LOCATOR 06-11 WIRE COLOR DTS 08-14 POSITION CADILLAC CTS 06-11 CONNECTOR TYPE Lucerne CONNECTOR COLOR 08-17 Driver Door Pin ~ ~ ~ ~ ~ ~ Do not connect.
PAGE 7
PAGE 7 OF 20 DOC.: #38693 • 20170427 GMC Savana SUZUKI SATURN PONTIAC HUMMER Sierra 17 08-17 07-13 Sierra Premium Package 07-13 Yukon / XL / Denali / Hybrid 07-14 H2 08-09 G8 Torrent Outlook 08-09 07-09 07-10 07-09 U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR ~ ~ ~ ~ ~ Do not connect.
PAGE 8
PAGE 8 OF 20 DOC.
PAGE 9
PAGE 9 OF 20 DOC.: #38693 • 20170427 Captiva Sport 6cyl STD key 08-15 08-10 Vue 6cyl STD key 08-10 U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Driver Door Pin ~ ~ ~ ~ ~ ~ Do not connect.
PAGE 10
PAGE 10 OF 20 DOC.
PAGE 11
MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 Close driver door. 07 02 Re-open driver door to wake up data bus. 08 Wait, LED 1 will turn solid GREEN for 2 seconds. (This may take up to 1 minute.) Turn key to OFF position. ACC OFF 03 Insert key into ignition. ACC ON START Module Programming Procedure completed. ON START OFF 04 09 PAGE 11 OF 20 DOC.: #38693 • 20170427 Turn key to ACC position. ACC ON START OFF 05 Wait, LED 1 will turn solid RED. 06 Turn key to ON position.
PAGE 12
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 01 Time restriction. Complete next step within 7 seconds. 02 OFF ACC ON START >> PAGE 12 OF 20 DOC.: #38693 • 20170427 To exit valet mode: repeat steps 1 to 5. Cycle ignition ON five times [5x OFF/ON] rapidly.
PAGE 13
AFTERMARKET REMOTE PROGRAMMING - 1 OF 1 PAGE 13 OF 20 DOC.: #38693 • 20170427 AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 FLC-GM(RS)-GM10-[FLRSGM10]-EN www.flashlogic.
PAGE 14
PAGE 14 OF 20 DOC.: #38693 • 20170427 MODULE NAVIGATION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. 04 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position.
PAGE 15
PAGE 15 OF 20 DOC.: #38693 • 20170427 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. 01 II Make sure the option is covered on the vehicle before attempting to change the setting.
PAGE 16
PAGE 16 OF 20 DOC.: #38693 • 20170427 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES 14 01 [Z] SETTINGS MODULE NAVIGATION CHART - 2 OF 2 HORN EVENT TRIGGER CONFIGURATION 15 02-07 Technical Support only 01 HORN CHIRPS WIDTH N/A 01 DOUBLE LOCK 02 LOCK + UNLOCK 03 LOCK + UNLOCK + START 04 DOUBLE LOCK + START 01 30 mSEC 02 15 mSec 03 60 mSec 01 N/A *Vehicle will shutdown when a door is opened. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc.
PAGE 17
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - 1 OF 1 I WARNING: The following applies only when the parking lights are connected and supported by the system. 03 Foot brake is ON. 04 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized.
PAGE 18
I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 DIAGNOSTIC TEST MODULE LED 1 STATUS MODULE DIAGNOSTICS - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed.
PAGE 19
MODULE RESET PROCEDURE - 1 OF 1 01 Disconnect all connectors from module except the BLACK 20-PIN connector. 07 Reconnect all connectors. 02 Disconnect the BLACK 20-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module’s programming button while connecting the BLACK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds.
PAGE 20
INSTALLATION CHECKLIST - 1 OF 1 PAGE 20 OF 20 DOC.: #38693 • 20170427 CHECKLIST 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock? ¨ YES: Go to next step. ¨ NO: Repeat step.