Owners manual

THE FLEX-A-LITE LIMITED WARRANTY
Flex-a-lite Corporation, P.O. Box 580, Milton, Washington 98354, Telephone No.. 253/922-2700, warrants to the original purchaser User,
all Flex-a-lite products to be free of defects in material and workmanship for a period of 365 days (1 year) from date of purchase. Flex-a-
lite products failing within 365 days (1 year) from date of purchase, may be returned to the factory through the point of purchase,
transportation charges prepaid. If, on inspection, cause of failure is determined to be defective material or workmanship and Not be
misuse, accident, or improper installation, Flex-a-lite will replace the fan free of charge, transportation prepaid. Flex -a-lite will Not be
liable for incidental, progressive, or consequential damages. Some states do Not allow the ex clusion or limitation of incidental or
consequential damages, so the above limitation or ex clusion may Not apply to you. This warranty gives you specific legal rights and you may also
have other rights, which vary from state to state. NOTE: The Flex-a-lite warranty is in compliance with the Magnuson-Moss
Warranty Act of 1975.
ASSEMBLY & MOUNTING INSTRUCTIONS
1. Assemble the brackets to the Flex-a-lite Scirocco
fan/shroud (Diagram A) using the button head
screws and lock nuts provided. Pass the button head
screws through the bracket flange holes, the shroud,
the motor struts on the inside of the shroud, and into
the lock nuts. Note: The half-round cut out in one
bracket is to allow clearance for the fan temperature
switch that mounts in the radiator tank face in some
models.
2. Route the motor lead wires so they pass through the clearance between the two ends of the bulb seal where they
come together. Fasten the wires to the motor struts to prevent the wires from contacting the blades. Use the nylon
ties provided.
3. Fan blades are factory mounted as pullers. To use as a pusher simply slide E-clips off the ends of the motor shafts,
reverse blades and slide E-clips back into position on the ends of the motor shafts.
4. For puller mode attache the black wire to a positive 12 volt power source and the red wires to ground. For pusher
mode attach the black wires to ground and the red wires to a positive 12 volt power source.
5. Mount the Flex-a-lite fan/shroud assembly to the radiator using the spacers*, bolts, washers and lock washer
provided (Diagram B). Always check to make sure there is sufficient clearance for the bolt threading into the radiator
mounting b bosses so that it does not bottom out and crack the radiator. If sufficient clearance does not exist use a
shorter bolt or a spacer under the head of the bolt.
*Spacers are used between the bracket and mounting bosses on radiators where the mounting bosses on one side of
the radiator are shorter than the other. The spacers allow the shroud to lay flat on the radiator core for even support and
a good seal.
SCIROCCO O.E. FAN REPLACEMENT
INSTRUCTIONS
1.Disconnect the battery ground cable.
2. Disconnect the fan motor wiring connector.
3. Remove the (4) shroud retaining bolts.
4. Remove the shroud and fan assembly from
the car.
5. Install Flex-a-lite fan/shroud assembled as
described above.
6. Fans can be wires by slicing into existing fan
wiring harness. For increased control of fan
purchase Flex-a-lite illuminated Switch
#31148 or Adjustable Temperature Sensor
#31147.
“GRIFFIN SCIROCCO RADIATOR ”
I
NSTALLATION:
1. Assemble the Flex-a-lite model 365 Scirocco fan according
to the instructions above, then follow theses directions for adding the additional set of holes in the mounting brackets.
2. Center the fan assembly between the two upper fan mounts on the radiator side tanks and fasten using the bolts
provided.
3. Mark lower mounting hole locations on the fan assembly mounting flanges so they line up with the lower set of fan
mounts on the radiator tanks.
4. Remove fan assembly from radiator.
5. Use file or drill to elongate the holes to fit the Griffin radiator holes.
6. Fasten fan assembly to radiator using the bolts, lock washers, and flat washers provided.
DIAGRAM A
DIAGRAM B
Button Head
Screw
Lock Nuts
Bulb Seal
Allen Cap Bolt
Lock Washer
Flat Washer
Spacer
(if needed)
SCIROCCO RADIATOR DUAL ELECTRIC FAN #365