Use and Care Guide

Flexco Floors | 1401 E. 6th St. - Tuscumbia, AL 35674
P: 800.633.3151 | flexcofloors.com | Made in the USA
07.28.2017 | Page 1
CARE & MAINTENANCE
TRIMS, TRANSITIONS & OTHER
ACCESSORIES
Accessories
Flooring accessories do not typically
require specialized maintenance or a
protective wax or floor finish within the
parameters of a maintenance program.
However, these products do require
daily and routine care and maintenance
with cleaning equipment to maintain
the desired appearance, which is usually
consistent with the adjoining floor
covering. The frequency of daily and
routine maintenance will depend upon
the amount and type of traffic in the area.
When installing vinyl accessories in areas
where desks, chairs and or furniture
with castors will be used, it is extremely
important to reduce the amount of
debris around the area of the chair,
furniture feet or castors. When furniture
is moved repeatedly, this debris can
build up underneath chair and furniture
feet or castors and cause damage to
the accessory. The chair castors and
other chair and furniture floor protection
devices must be regularly inspected for
debris, build-up or damage and cleaned
when necessary.
Always use untreated, new or
thoroughly cleaned mops, towels,
cloths and pads when conducting daily
or routine maintenance. Do not use
Kerosene, Gasoline, Naphtha and/or
other solvents to clean Rubber Tile. As
with any maintenance program, be sure
to use proper PPE (Personal Protective
Equipment) per the cleaning product SDS
and ensure all maintenance procedures
are conducted per the cleaning products
instructions. The use of Caution Tape and
/or Wet Floor Signs are recommended to
prevent slips and falls.
Maintenance Overview
Approved Cleaners
Excelsior NC-900 Neutral Cleaner
Excelsior CM-910 Cleaner / Maintainer
Approved Finish Removers
Excelsior FR-920 Finish Remover
Technical Documents & Support
Additional product resources and technical documents are
available online at flexcofloors.com. For additional technical
support, send an e-mail to [e-mail].
Additional Information
1. POST-INSTALLATION CHECKLIST
• Prior to moving furniture or heavy equipment, sweep or
wipe the material and cover with an appropriate protective
product, such as Masonite, Ram Board or equivalent, to
prevent scuffing and scratching that may not come out
during the maintenance procedures.
• DO NOT use vacuums that have a beater bar or electric
brooms with hard plastic bottoms or no padding, as this may
cause discoloration, scratching and loss of sheen.
• DO NOT use highly alkaline or acidic cleaners.
• DO NOT use detergents, abrasive cleaners or “mop and
shine” type products, as they will dull the finish and sheen
of the flooring material.
• DO NOT use sweeping compounds or cleaning agents
containing oils or solvents.
• DO NOT scrub, buff or mop the area per the adhesives traffic
limits (48-72 hours) to allow proper curing of the adhesive.
• DO NOT flood the area when cleaning.
• DO NOT allow the cleaning solution or topical moisture to
work its way beneath the material, as this can result in an
adhesive and/or installation failure.
2. INITIAL MAINTENANCE
Ensure that adhesive has cured for recommended period of time
prior to conducting initial maintenance. Remove any protective
coverings prior to cleaning. Sweep, dust mop, vacuum or
wipe material to remove any dirt, dust or debris. Do not use
vacuums that have a beater bar or electric brooms with hard
plastic bottoms or no padding, as this may cause discoloration,
scratching and loss of sheen. Do not use detergents, abrasive
cleaners or “mop and shine” type products, as they will dull the
finish and sheen of the flooring material.
Mix 2-4 ounces of Excelsior NC-900 Neutral Cleaner per gallon
of clean, potable water. Use a clean mop, cloth or towel to apply
cleaner to material. If necessary, scrub material while wet using
a 22 gauge soft bristled scrubbing brush. If heavily soiled, an
additional cleaning or scrubbing may be required. Use an auto-
scrubber, wet vacuum, clean mop or clean cloth to remove any
and all excess cleaning solution. Rinse area with clean, cool
water and allow material to dry entirely. Ensure material is clean
and that all cleaning residue has been removed (this may require
additional rinsing).
3. DAILY MAINTENANCE
Ensure that initial maintenance has been conducted prior to
conducting daily maintenance. Sweep, dust mop, vacuum or
wipe material to remove any dirt, dust or debris. Do not use
vacuums that have a beater bar or electric brooms with hard
plastic bottoms or no padding, as this may cause discoloration,
scratching and loss of sheen.
Mix 2-4 ounces of Excelsior NC-900 per gallon of clean, potable
water. Use a clean mop or cloth to clean spills, dirt buildup and
other debris. Allow material to dry before allowing foot traffic.