Installation Guide

ManualsBrandsFlexco ManualsFlooringPrime Sports 5-Pack 18-in x 18-in Blue Ice Color flecked Rubber Roll Multipurpose Flooring

INSTALLATION INSTRUCTIONS and TECHNICAL DATA

RECYCLED RUBBER FLOORING

Prime Sports™

TECHNICAL DATA

Nominal Dimensions - Square Edge: 36” x 36” (Area: 9 sq. ft.)

Nominal Dimensions - Interlocking: 34 ¼” x 34 ¼” (Area: 8 sq. ft.)

Nominal Dimensions - Rolls: 48” x 49 ½’ (198 sq. ft.)

Custom Rolls: 48” x 24’ up to 49 ½’, in 1’ increments

Finish: Characteristic Texture

Thickness: 5/32”, 1/4”, 3/8”, 1/2”

Weight per Tile/Roll: 8.2 – 10.7 lbs. (tile) 101 – 262 lbs. (per roll)

(Weight varies based on area/thickness)

ASTM F3041 - Bonded Crumb Rubber: Type I & II, Class A, B, C & D

ASTM D2047 – Coefficient of Friction: >0.8

ASTM E648 (NFPA 253) - Critical Radiant Flux: Unclassified, 0.10 W/cm²

ASTM D3389 - Abrasion Resistance: Passes

ASTM F137 - Flexibility: Passes

ASTM F970 - Static Load Limit: Passes, 250 PSI

ASTM F2199 - Dimensional Stability: Passes

ASTM F1514 - Heat Stability of Color: Passes

ASTM F925 - Short Term Chem. Exposure: Passes

ASTM E492 Impact Sound Transmission: 7 IIC

Acclimation Time: 48 Hours

Storage & Acclimation Temperature: 65° - 85° F

SUSTAINABILITY

Qualifies for LEED Credits

Technical Support: solutions@rhctechnical.com

APPROVED ADHESIVES

Excelsior MS-700 Modified Silane Wet-Set – A premium, one component modified silane adhesive used for the

permanent installation of vinyl & rubber flooring products over porous and non-porous substrate both indoors and

outdoors.

Excelsior U-705 Urethane Wet-Set Adhesive – A premium water resistant, single component urethane adhesive

used for the permanent installation of resilient flooring products, including recycled or crumb rubber flooring products

over porous and non-porous substrates both indoors and outdoors.

Excelsior EW-710 Epoxy Wet-Set Adhesive – A non-flammable two-part urethane-modified epoxy adhesive used for

the permanent, installation of vinyl, rubber and quartz flooring products over porous and non-porous substrates in both

indoor and outdoor applications.

Summary of content (8 pages)

PAGE 1
Prime Sports™ INSTALLATION INSTRUCTIONS and TECHNICAL DATA RECYCLED RUBBER FLOORING TECHNICAL DATA Nominal Dimensions - Square Edge: Nominal Dimensions - Interlocking: Nominal Dimensions - Rolls: Custom Rolls: Finish: Thickness: Weight per Tile/Roll: (Weight varies based on area/thickness) ASTM F3041 - Bonded Crumb Rubber: ASTM D2047 – Coefficient of Friction: ASTM E648 (NFPA 253) - Critical Radiant Flux: ASTM D3389 - Abrasion Resistance: ASTM F137 - Flexibility: ASTM F970 - Static Load Limit: ASTM F2199
PAGE 2
Prime Sports™ RECYCLED RUBBER FLOORING INSTALLATION INSTRUCTIONS and TECHNICAL DATA Adhesive Coverage Rates, Moisture Limits and Traffic Limits Coverage Rates (per gallon) Moisture Limits Traffic Limits & Maintenance Limits Adhesive Porous Non-Porous RH / MVER Limits Foot Traffic Heavy Foot Traffic, Rolling Loads Maintenance MS-700 135 sq. ft. 160 sq. ft. 95% / 10 lbs. 8-12 Hours 24-48 Hours 48 Hours U-705 135 sq. ft. 160 sq. ft. 100% / 25 lbs.
PAGE 3
      Do not stack pallets to avoid damage. Remove any plastic and strapping from product after delivery. Inspect all material for proper type, color and matching lot numbers if appropriate. Ensure that all adhesives intended for installation are approved for use with flooring material. Ensure HVAC system is operational and fully functioning at normal operating conditions.
PAGE 4
New or existing concrete substrates on all grade levels must be tested in accordance with ASTM F2170, using in situ Probes, to quantitatively determine the amount of relative humidity no more than one week prior to the installation.
PAGE 5
All grout lines and irregularities must be filled and troweled flush with a suitable primer and patch such as the Excelsior NP-230 and CP-300 to prevent telegraphing of the existing floor. All existing flooring substrates that are outside of flatness tolerances that cannot be repaired with the Excelsior CP-300 patch should be leveled with the SU-310 self-leveling underlayment to achieve a smooth, flat substrate.
PAGE 6
Ensure adhesive is approved for use with flooring material and the proper trowel type and size is used, as manufacturer is not responsible for any and all adhesion issues related to improper adhesive selection or usage. Prior to installation, confirm material installation pattern and direction per design specifications or work order. Observe directional arrows, (this side up) on face of tile to ensure arrows are installed in the same direction.
PAGE 7
Ensure flooring seams do not directly overlap flooring seams any seams in substrate. After positioning the first roll of material, position the second roll alongside the first roll and check factory side seams for seam acceptable. If the factory side seams are not acceptable the material should be double cut or scribe cut using a straight edge prior to installation to ensure tight seams. If the factory side seams are acceptable overlap the second roll over the side seam of the first roll no more than 1/16”.
PAGE 8
Do not apply finish to areas that may be exposed to heavy weights, heavy use or high/heavy impact. For further information regarding daily or routine maintenance, please consult the product care & maintenance document or the associated product technical data sheet. 10. FLOORING PROTECTION Protect newly installed stair treads, risers and stringers with construction grade paper, such as Ram Board, to protect material from damage by other trades.