Use and Care Guide

Flexco Floors | 1401 E. 6th St. - Tuscumbia, AL 35674
P: 800.633.3151 | flexcofloors.com | Made in the USA
07.31.2017 | Page 1
CARE & MAINTENANCE
RUBBER WALL BASE
Wallflowers
Wallflowers Rubber Wall Base does not
typically require specialized maintenance
within the parameters of a maintenance
program. However, these products may
require occasional cleaning, which is
usually consistent with the adjoining
floor covering. The frequency of daily and
routine maintenance will depend upon
the amount and type of traffic and wear
in the area.
When installing Wallflowers wall base in
areas where desks, chairs and or furniture
with castors will be used or in areas
where auto-scrubbers and/or vacuums
will be used, it is extremely important
to protect the base from unnecessary
damage due to moving furniture or
equipment. Whenever possible, prevent
damage and abuse to wall base.
Always use untreated, new or thoroughly
cleaned cloth when conducting daily
or routine maintenance. Do not use
Kerosene, Gasoline, Naphtha and/or
other solvents to clean wall base. As
with any maintenance program, be sure
to use proper PPE (Personal Protective
Equipment) per the cleaning product SDS
and ensure all maintenance procedures
are conducted per the cleaning products
instructions.
Maintenance Overview
Approved Cleaners
Excelsior NC-900 Neutral Cleaner
Excelsior CM-910 Cleaner / Maintainer
Approved Finish Removers
Excelsior PR-930 Performance Remover
Technical Documents & Support
Additional product resources and technical documents are
available online at flexcofloors.com. For additional technical
support, send an e-mail to [e-mail].
Additional Information
1. POST-INSTALLATION CHECKLIST
• When moving furniture or heavy equipment, protect wall
base from scuffing and scratching that may not come out
during the maintenance procedures.
• DO NOT use vacuums or electric brooms which have beater
bars, hard plastic bottoms, a rubber bumper or are lacking
proper padding or protection, as this may cause marking,
discoloration, scratching and loss of sheen.
• DO NOT use detergents, abrasive, alkaline or acidic cleaners,
cleaning agents which contain oil or solvents, as well as
“mop and shine” type products, as they will dull the finish
and sheen and potentially damage the wall base material.
• DO NOT clean area per the adhesives traffic limits (48-72
hours) to allow proper curing of the adhesive.
• DO NOT flood the area when cleaning.
• DO NOT allow the cleaning solution or topical moisture to
work its way beneath the material, as this can result in an
adhesive and/or installation failure.
2. INITIAL MAINTENANCE
Ensure that adhesive has cured for recommended period of time
prior to conducting initial maintenance. Remove any protective
coverings prior to cleaning. Sweep, dust or wipe material to
remove any dirt, dust or debris. DO NOT use vacuums or electric
brooms which have beater bars, hard plastic bottoms, a rubber
bumper or are lacking proper padding or protection, as this may
cause marking, discoloration, scratching and loss of sheen. Do
not use detergents, abrasive cleaners or “mop and shine” type
products, as they will dull the finish and sheen of the material.
Mix 2-4 ounces of Excelsior NC-900 Neutral Cleaner per gallon
of clean, potable water. Use a clean towel or cloth to apply
cleaner to material. If heavily soiled, an additional cleaning may
be required. Use clean towel or cloth to remove any and all
excess cleaning solution. Rinse area with clean, cool water
and allow material to dry entirely. Ensure material is clean and
that all all cleaning residue has been removed (this may require
additional rinsing).
3. DAILY MAINTENANCE
Ensure that initial maintenance has been conducted prior
to conducting daily maintenance. Sweep, dust mop or wipe
material to remove any dirt, dust or debris.
Mix 2-4 ounces of Excelsior NC-900 per gallon of clean, potable
water. Use a clean mop or cloth to clean spills, dirt buildup and
other debris. Allow material to dry before allowing foot traffic.
4. MATERIAL PROTECTION
Protect newly installed material with construction grade paper
or protective boards, such as Masonite or Ram Board, to protect
material from damage by other trades. Limit usage and foot
traffic according to the adhesive's requirements. When moving
appliances or heavy furniture, protect wall base from scuffing
and tearing using temporary floor protection.
For more information regarding cleaner
application, floor finish application or finish
removal, please consult the associated Excelsior
product data sheet.