USER MANUAL For Flic English
Welcome to the Flic family! Take control and simplify your life with the push of a Flic.
Contents Setup guide 1 Pairing your Flic 2 Bluetooth connection 3 Stick your Flic anywhere 4 Cleaning the reusable adhesive 5 Using the clip accessory 6 Changing the battery 7 Problems? 8 Compliance 10 Safety usage guidelines 11 Battery warning 12 Battery & device disposal 12 Warranty 13
Setup guide To get started, you will need the following: 1. A device supporting* iOS or Android with Bluetooth® Smart (BLE 4.0) 2. An active internet connection 3. The Flic app, available on the App Store or Google Play For more information on setting up your Flic for the first time and to see instructional videos go to https://start.flic.io/ *Device compatibility is subject to change. Current minimum requirements available at https://flic.
Pairing your Flic 1. Make sure Bluetooth is activated on your phone. 2. Open the Flic app, create an account and login. 3. Follow the interactive app guide to get your Flic paired with your phone. 4. Now you are ready to set up your first actions.
Bluetooth connection When setting Flic up be sure to connect to your device through the Flic app. iOS users: An in app pop up will ask you to confirm the Bluetooth connection with your device. Android users: Do not try to pair with your Flic through the Bluetooth settings ‘Available devices’ page. Always keep your Bluetooth turned on to ensure your Flic stays connected with your device. Bluetooth works within range of up to 50m. Make sure your Flic stays close to your device to ensure a stable connection.
Stick your Flic anywhere Each Flic comes with a reusable adhesive sticker (pre attached to the base) which can be used again and again. Simply peel off the protective film and stick your Flic on any clean surface.* If you want to change the position of your Flic you can remove it by peeling** both the Flic and adhesive off the surface. The special adhesive used with Flic should leave the surface undamaged and mark free, as long as the adhesive was clean prior to mounting.
Cleaning the reusable adhesive To clean your adhesive, remove it from the Flic’s base and rinse with water. Give it a rub and rinse again. Do not apply solvents, chemicals or abrasive cleaning products as this will damage the adhesive. Leave it to air-dry and it will return to full stickiness. You can now mount it again and stay confident that your Flic will remain where you stick it.
Using the clip accessory To attach your clip you need to open the base of the device. The easiest way to open it is to use the adhesive and stick your Flic on a surface. Once in place simply twist anticlockwise and your Flic should pop open. To attach the clip make sure the battery is seated correctly and then align the three tabs on the clip with the respective slots on the Flic. Firmly push in place and twist clockwise until you hear a click. The click noise signifies that the clip is correctly attached.
Changing the battery The Flic uses a CR2016 coin cell battery. To change the battery you need to open the base. Check the “Using the clip accessory” (page 6) to learn how to open your Flic. Remove the old battery and replace with a new CR2016 with the positive (+) side facing up. Slot the battery in the direction of the V contact first and then apply downward pressure until the battery locks in position.
Problems? If you are unable to connect your Flic or have any other issues then please read our FAQ’s. They can be found at https://start.flic.io/faq Alternatively you can contact us via the in-app customer support or email us at support@shortcutlabs.
Shortcut Labs AB Disclaimer This contains important information regarding device set up, product compliance, safety and warranty information. Flic and Shortcut Labs are trademarks of Shortcut Labs AB C 2017. All other trademarks and logos are properties of their respective owners.
Compliance Shortcut Labs declaration of conformity is available at https://flic.io/doc For a full compliance list visit https://flic.io/compliance Flic is certified as FCC, IC, CE, TELEC, WEEE, RoHS, REACH, AUS and R-NZ compliant.
Safety usage guidelines • Flic is not a toy. It contains small parts and accessories that present a choking hazard. As such it is not suitable for children or pets. • Do not attempt to service the product. • Battery life will be shortened with heavy usage and/or use in extreme conditions. • Do not use the product in temperatures below -20 degrees Celsius or above +54 degrees Celsius. • Flic is rated as splash proof only - IP44.
Battery warning This device contains a battery composed of lithium, organic solvents, and other combustible materials. For this reason, improper handling of the battery could lead to distortion, leakage, overheating, explosion or fire, causing personal injury. Please observe the following instructions to prevent accidents. Never swallow, charge, heat, expose to open flames, moisture, liquid. Never attempt to disassemble, reverse the polarity or short circuit. Keep away from children and pets.
Warranty Shortcut Labs AB warrants that your Flic hardware product (“the product”) will be free from defects in materials and workmanship for a period of 24 months from the date of delivery to the original retail purchaser (“the warranty period”).
Join the Flic community! https://community.flic.io/ Share your ideas with other Flic users and keep up to date with the latest news and happenings from the Flic team.
