Hawker FB.11 User Manual www.sz-freewing.
Introduction FlightlineRC is a new brand from Freewing Models, designed to bring you a new generation of propeller aircraft with high performance at an affordable price. We will continue to deliver innovative ideas and exquisite designs, and provide propeller aircraft with the same high level of quality our customers expect and deserve. SUMMARY: The Hawker Sea Fury was the last piston engine driven carrier based fighter in British history.
Index 1. Product Basic Information 2. Package List 3. Assembly: 4. Main Wing 5. Tail gear, rudder and elevator 6. Elevator, Tail Wheel Pushrods 7. Tail Hook, Main Landing Gear 8. Servo Introduction, Battery Installation 9. Power System Installation 10. Motor Parameters, CG 11. Control Direction Test 13.
Product basic information C -.- Wing loading:78g/dm2 Motor:3748-580KV brushless motor Propeller:4-blade 12x7 ESC: 60A brushless ESC Servo:9g MGx2, 9g plasticx4 Weight: 1550g (w/o battery) Aileron: Yes Elevator: Yes Rudder: Yes Flap: Yes Landing gear: retract landing gear Cabin door Material: EPO High speed DIY spare-part (The following is DIY spare-part, please contact distributor to purchase separately.
Assembly •Main wing Install main wing servos 1.Use a servo tester or radio to center the servo. 2.Use glue to install the servo and aileron horn on the main wing. 3.Feed the servo cable through the slot. A-9g servo B - Main wing pushrod C -Aileron horn D - Main wing servo slot 4.Insert the pushrod into the servo arm, adjust its length, then insert the clevis into the control horn and lock it into place. 5.Repeat the above four steps for all aileron and flap servos, then apply the decal over the slots.
Assembly • Installation and assembly of the tail gear. 1.Assemble the tail wheel as shown in the diagram. EN A- Rear wheel (035x10mm) B- Rear gear supporting rod C- Rear wheel shaft 0- E-buckle (05x02mm) D A 2.lnsert the tail gear set C to the fixed plastic part B, and then insert it into the tail steering arm A . 3.Use screw D t o fix the tail steering arm. c� --@� -- A- Tail steering arm B - Rear gear fixed plastic part C - Tail gear set D-Screw (PA1.
Assembly EN Installing elevator/rudder pushrods --• 1.lnsert one side of the rudder pushrod A ,through plastic tube B, to the servo arm C. 2.Snap the clevis of the rudder pushrod into the rudder horn D and secure it with the rubber retainer. C B 1.lnsert one side of the elevator pushrod A ,through plastic tube B, to the servo arm C. 2.Snap the clevis of the elevator pushrod to the rudder horn D and secure it with the rubber retainer.
Assembly C Installing the tail hook 1.lnsert the tail hook A on the tail hook fixed part B, and keep the two plastic holes alignment; 2.Use screw C to secure the tail hook A. \ A -Tail hook B -Tail hook fixed part C -Screw (PA2x11mm) Installing the drop tanks Install main wing guns Use glue to attach the drop tanks on the left/right main wing. Ensure you have the correct tank for each wing. Apply glue to the gun holes, then insert the carbon tubes to the gun hole as shown.
Servo introduction i ) A servo or reversed servo is defined as follows: When the servo input signal changes from 1000ųs to 2000ųs, The servo arm rotates clockwise, its a positive servo. If it rotates counter clockwise, its a reversed servo. . · ·· .. / II If you need to purchase other brand of servo, please refer to the following list to choose correct size. Servo installing position No. Pos./Rev.
Installing the power system A-Screw (KM3x5mm 4pcs) B-Motor X-fixed base C-3748-580KV out-runner motor D-Propeller folder E-Screw (HM2.5x10mm 4pcs) \ A-Motor fixed mount B-Screw (PA3x12mm 4pcs) C-Screw (PA2.3x16mm 8pcs) D-Scale propeller (12 x7, 4-blade ) E-Scale propeller fixed plate E \ .../ • ·- ··---e . ... A-Screw (PM3x1Qmm 1pcs) B-Spinner (scale 4-blade spinner) C-Propeller fixing bolt 0-Washer (<1>14x1.5x6.2mm) \--Installing the optional 2-blade propeller high power system A-Screw (PM3x1Q
Parameter of Motor l=N Unit: mm Unit: mm 4-M3.0 037.5 09.0 09.0 4-M2.5 4-M2.5 12.5 12.5 3748-580KV / 3648-880KV 3648-880KV 3748-580KV Item No. KV Value Volate (V) Current (A) Pull (g) Motor Resistance Wei ght (g) M0137481 580RPM/V 14.8 41 2500 0.020 170 2.3A/1 OV 4-B1ade12x7 �60A M0136484 880RPM/V 14.8 53 2600 0.020 165 2.3A/10V 2-B1ade12x8 �60A Motor shaft, X-fixed base 09 .0 H-------r-,=i uHt Unit: mm J •• �J 020 �4-02.
Control direction test After the build is complete but with the propeller removed, power up the radio and connect a fully charged battery to the ESC. Use the radio to ensure proper control direction Aileron Stick Left •• Stick Right •• !!! !!! Elevator Up Elevator Down Elevator Rudder Stick Left Stick Right Optional Flaps Flaps down Pliqhtrfo.!!. Hawker!ieaFury FB.11 /ten, Na.
Dual Rates N According to our test results, the following rates proved to be a good starting point. Low rates are good for initial flights or less experienced pilots. Adjust rates to suit you own style.
