CEILING FAN
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER THANK YOU FOR YOUR PURCHASE Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all instructions before using the product SAFETY TIP 1. To avoid possible electric shock, turn ON t he electricity at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan o r installing accessories . 2.
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Plastic wire nut (3PCS) Mounting screw(2PCS) L N Blade screw (1PC) Washer(2PCS) Washer (19PCS) Safety cable screw(2PCS) 5g Washer(2PCS) Balancing sticker (2PCS) Remote control (1 PC) Balancing clip (1PC) Fan motor assembly Blades(6 PCS) Pls check whether above accessories are completed or not?Yes,and install.
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER X18 X6 X2 x2 X18 X18 X6
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER x2 x2 mounting bracket outlet Outlet box Mounting bracket Washer Mounting screw
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER X1 Black MOTOR FROM POWER SOURCE AC 110- 120 VOLT 60Hz 3.5AMPS.
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER X3 X3 The remote controller controls the fan as follows: FAN ON/OFF - for fan on/off LIGHT ON/OFF - for light on/off 1 - for fan spead F/R - for fan reverse/forward function 2 - for fan spead 1H - 1 hour timer for fan and light 3 - for fan spead 4H - 4 hours timer for fan and light 4 - for fan spead 8H - 8 hours timer for fan and light 5 - for fan spead LIGHT ON/OFF FAN ON/OFF
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER size of product 9 9 4in or 10in 1610 in or 2110in 9in or 14in 1 22in 6in 3 105in 70in ∅70in
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Receiver (inside)
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER . .
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER TROUBLESHOOTING GUIDE Table of Contents 1. 2. 3. 4. Fan / Remote is not working Fan is noisy Fan Wobbles Light is not working Please refer to the instruction sheet for detailed directions and descriptions of installation steps and requirements. 1. FAN / REMOTE IS NOT WORKING Ensure the remote is within the 20 foot range of the receiver To reset the remote control: 1) Turn off power to fan using the wall switch or circuit breaker.
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER 3. THE FAN WOBBLES Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). Once fan is properly installed, run the ceiling fan for 10 minutes to let the fan self-adjust. If wobble occurs a er running the fan for 10 minutes, verify blade level using the following process: a) select a point on the ceiling above the p of one of the blades.
Installation & Operating Instructions for the Installation ,Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER AFTER INSTALLATION WOBBLE” The fan blades have been adjusted in the factory to minimize any wobble NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION.
