CEILING FAN
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER THANK YOU FOR YOUR PURCHASE Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all instructions before using the product SAFETY TIP 1. To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 2.
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Wood screws (4PCS) Mounting screws (2 PCS) Plastic wire nut (6 PCS) Blade screw (19PCS) washer (2PCS) Balanced parts package Blade bracket screws spring washer (1PCS) Blade washer (19PCS) (1PCS) (2PCS) AC IN L AC IN N GROUND MOTOR W MOTOR V MOTOR U 30' AC L AC N 4 REMOTE CONTROL(1PCS) Blade (5PCS ) Blade bracket (5PCS) Pls check whether above accessories are completed or not?Yes,and in
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Finish Finish
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Outlet box washers spring washer 1 2 3
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Finish Finish
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Use wire connecting nuts supplied with the fan FROM POWER SOURCE AC 110- 120 VOLT 60Hz 3.5AMPS. WHITE RED or BLACK ANT INPUT OUTPUT RECEIVER WIRE NUT CANOPY Insert the corresponding port of the fan cable into the remote control . RECEIVER (FIG.
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER RE D Finish
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Remote controller GENERAL INFORMATION INSTALLING RECEIVER IN CEILING FAN A.Safety precautions: RECEIVER (FIG.4) WARNING:HIGH VOLTAGE! Disconnect power by removing fuse or switching off circuit breaker. Do not use with solid state fans. Electrical wire must meet all local and national electrical code requirements. B.
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER size of product 355 ［14"］ Ø171 ［6.7"］ 260 ［10.2"］ Ø26.5 ［1 1/20"］x4"or10" 170 ［6.7"］ Ø150 ［5 9/10"］ Ø310 ［12.
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER TROUBLESHOOTING GUIDE Table of Contents 1. 2. 3. 4. Fan / Remote is not working Fan is noisy Fan Wobbles Light is not working Please refer to the instruction sheet for detailed directions and descriptions of installation steps and requirements. 1.
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER 3. THE FAN WOBBLES Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). Once fan is properly installed, run the ceiling fan for 10 minutes to let the fan self-adjust. If wobble occurs a er running the fan for 10 minutes, verify blade level using the following process: a) select a point on the ceiling above the p of one of the blades.
Installation & Operating Instructions for the Manual WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER AFTER INSTALLATION WOBBLE” The fan blades have been adjusted in the factory to minimize any wobble NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION.
