Owner's manual

ManualsBrandsFlint & Walling ManualsEquipment115V Pond and Fountain Systems FPS0501

Description

This pump system is designed for decorative use and can

improve water aeration. It produces water fountains up to 15’

in height, and up to 4,900 gallons of water per hour. Make

your floating fountain system even more dramatic at night by

adding the NightBright lighting system 023069.

Operates in 5 feet of water or deeper.

Unpacking

When unpacking the unit, inspect carefully for any damage

that may have occurred during transit.

021626

Floating Pond Pump System

Models FPS0501 and SPS0501

Operating Instructions & Parts Manual

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product

described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in

personal injury and/or property damage! Retain instructions for future reference.

FW0779

1013

Supersedes

0512

General Safety Information

Carefully read and follow all safety instructions in this

manual and on pump. Keep safety labels in good condi-

tion. Replace missing or damaged safety labels.

This is a SAFETY ALERT SYMBOL. When you see

this symbol on the pump or in the manual, look for one of

the following signal words and be alert to the potential for

personal injury or property damage.

Warns of hazards that WILL cause serious

personal injury, death or major property damage if ignored.

Warns of hazards that CAN cause serious

personal injury or death, if ignored.

Warns of hazards that MAY cause minor

personal injury, product or property damage if ignored.

IMPORTANT: Indicates factors concerned with operation,

installation, assembly or maintenance which could result in

damage to the machine or equipment if ignored.

NOTE: Indicates special instructions which are important but

are not related to hazards.

For installation

videos and other

information, scan

with your smart

phone.

1. Introduction

2. Safety

3. Tools required

4. 115V installation

a. Pre-installation

b. Installation

5. 230V installation

a. Pre-installation

b. Installation - pump

c. Installation - control center

d. Setting timers

e. Setting the clock

6. Scheduled maintenance

7. Seasonal removal and storage

Summary of content (4 pages)

PAGE 1
Operating Instructions & Parts Manual FW0779 1013 Supersedes 0512 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
PAGE 2
Never enter the water either wading, swimming or in a boat with the pump power on, as this may result in severe electrical shock. Always use caution when operating electrical controls in damp areas. If possible, avoid all contact with electrical equipment during thunderstorms or extreme damp conditions. ! Read these warnings and instructions carefully. Failure to follow could result in serious bodily injury and/or property damage.
PAGE 3
6. Before connecting the unit to the power receptacle, check to insure there is no leakage to ground. This can be done by using an ohm meter and setting the scale to its highest setting (i.e. Rx100K). Connect one ohmmeter lead to the unit power cord ground (round prong) and to one of the flat prongs. It should read infinite or at least 2 mega ohms. Repeat with the other prong. If reading is below 2 mega ohms on either prong contact Customer Service Help Line listed at bottom of page. up This si de 7.
PAGE 4
1 2(A/B/C) 3 TROUBLESHOOTING GUIDE 4 Problem Possible Causes Corrective Action 5 Unit won’t run Circuit breaker tripped Reset circuit breaker No or low spray GFI Trips Unit spins 6 GFI Tripped Reset GFI Blocked screen or nozzle, missing or damaged o-ring, or incorrectly installed nozzle Disconnect power. Clean screen and/or nozzle. Check that o-ring is undamaged and seated in groove. Check that nozzle is installed properly (nozzles are marked “This side up”). Check depth of pond.