Quick Installation Guide

ManualsBrandsFlir ManualsNetwork640 X 512 Network Outdoor Thermal Imaging Camera with 9mm Lens

Table Of Contents

1 Quick Install Guide

427-0102-00-28 Triton FH-Series QIG Rev 110

November 2021

This document does not contain any export-controlled information.

Triton™ FH-Series

Quick Install Guide

1 Check Contents

The camera kit includes a bag containing:

a T10 Torx wrench

two 10-pin connectors for I/O terminal blocks

one three-pin connector for 12 VDC terminal block

three two-pin connectors for 24 VAC output / input terminal blocks

In addition, watertight cable glands and seal plugs are attached to the camera's

rear cable ingress holes.

If any of these items are missing or damaged, contact your dealer or Teledyne

FLIR Support.

2 Select a Location

Triton FH-Series cameras are intended to be mounted on a medium-duty fixed

pedestal mount or wall mount commonly used in the CCTV industry, at an

installation height of at least 4 m (13 ft). The mount must support up to 30 lbs (15

kg). For the full list of mounting and other accessories available for the camera

from Teledyne FLIR, see the FLIR Security - Accessory Guide.

If you are powering the camera with PoE 70W class 8 or 24V AC / DC, verify that

the operating temperature is -40°C to 70°C (-40°F to 158°F) with cold start at -40°

C (-40°F), 0-95% relative humidity. Other power sources limit low-temperature

operation. For more information, see the camera's installation and user guide.

For further advice on positioning and orienting the camera, see the camera's

installation and user guide.

Supplying Power to the Camera

The camera can be powered by 12 VDC (±10%); 24 VDC (±10%); 24 VAC

(±10%); or PoE IEEE 802.3bt 50W class 6 or 70W class 8. Teledyne FLIR

recommends using PoE class 8 or 24 VAC / VDC.

Nominal power consumption is 15W; 48W on 12 VDC with heaters enabled; and

70W on all other input voltages with heaters enabled.

Summary of content (10 pages)

PAGE 1
Triton™ FH-Series Quick Install Guide 1 Check Contents The camera kit includes a bag containing: · a T10 Torx wrench · two 10-pin connectors for I/O terminal blocks · one three-pin connector for 12 VDC terminal block · three two-pin connectors for 24 VAC output / input terminal blocks In addition, watertight cable glands and seal plugs are attached to the camera's rear cable ingress holes. If any of these items are missing or damaged, contact your dealer or Teledyne FLIR Support.
PAGE 2
3 Connect the Camera To install the camera, Teledyne FLIR recommends connecting the camera on a bench or in a lab and configuring it for networking before mounting and aiming it. However, circumstances can dictate adjusting the sequence of the steps. For example, you can mount the camera before configuring it for networking, or connect the camera before mounting it. Warning The camera itself does not have a power on/off switch.
PAGE 3
You do not need to remove the sunshield to open the cover. Nonetheless, if you want to remove the sunshield, loosen and remove the screws that attach it to the camera body. Then, carefully remove the sunshield. b. Open the camera cover to expose the inside of the camera body and the following connections. Camera Connections Connection 1 LAN (56V 1.6A) PoE 802.3bt 2 BNC x2 3 Description Attach a Cat 6 cable from the network switch to the RJ45 port for 100/1000 Mbps Ethernet and PoE.
PAGE 4
Connection 4 5 6 Description Connect wires from alarm or audio I/O devices, or from IR LED illuminators, to the appropriate pins on a ten-pin connector included in the camera kit. Then, plug the connectors into the terminal blocks. To use the camera's external IR illumination feature to turn illuminators on and off, connect them to ALARM OUT 2.
PAGE 5
Caution Make sure the camera is properly grounded. Failure to properly ground the camera can permanently damage the camera. 4 Configure for Networking To discover the camera on the network, Teledyne FLIR recommends using the FLIR Discovery Network Assistant (DNA) tool. Version 2.3.0.20 or higher supports Triton FH-Series, does not require a license to use, and is a free download from the product's web page on the Teledyne FLIR website.
PAGE 6
If this is the first time you are configuring the camera or if it is the first time after resetting the camera to its factory defaults, DNA automatically authenticates the camera with the default password for the camera's admin user (admin). If the admin user password has been changed, you need to authenticate the camera. In the DNA Discover List, right-click the camera and select Login. In the DNA - Login window, type the password for the admin user.
PAGE 7
Install the mounting hardware for the camera according to the instructions for the hardware. If relevant, route power, network, and other cables into the mounting hardware so that they are accessible when the camera is mounted. Typically, point the camera towards the ground while ensuring that the field of view includes as little of the skyline as possible. Teledyne FLIR recommends mounting the camera with zero horizontal rotation; that is, a 0º installation roll angle.
PAGE 8
To ensure a watertight seal, fully tighten the gland nuts. Close and Secure the Cover Using the Torx wrench, alternately tighten the four screws that secure the cover to the camera; torque to 8+0.5 kgf-cm. To ensure the camera's IP66 and IP67 dust and water ingress ratings, properly and securely close the camera cover and Caution tighten the screws. Failure to do so can void the camera's warranty. Re-attach the sunshield, if relevant.
PAGE 9
h. Click Display Target. A box simulating a 1.8m (5" 11') person appears in the live video. Make sure the height of the box corresponds to the size of the person standing in the camera's field of view. If it does not, on the Georeference page, verify the camera's installation height, tilt angle, and roll angle. On the Boresight page, make sure the visible and thermal video vertical fields of view are properly aligned. i. On the Thermal tab, make sure analytics are enabled, and repeat the previous two steps.
PAGE 10
Attach the Camera to a Supported VMS After you have mounted the camera and discovered or defined its IP address, attach the camera to a supported VMS using its discovery/attach procedure. 11 Camera Dimensions The Triton FH-Series camera’s dimensions are: 12 Register the Product Register the product at https://customer.flir.com. For warranty information, see https://www.flir.com/supportcenter/warranty/security/flir-security-product-warranties/.