IOI HD User and Installation Guide CF-5212/CF-5222 Ver.
© 2017 FLIR Systems, Inc. All rights reserved worldwide. No parts of this manual, in whole or in part, may be copied, photocopied, translated, or transmitted to any electronic medium or machine readable form without the prior written permission of FLIR Systems, Inc. Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Systems, Inc. and/or its subsidiaries.
Proper Disposal of Electrical and Electronic Equipment (EEE) The European Union (EU) has enacted Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE), which aims to prevent EEE waste from arising; to encourage reuse, recycling, and recovery of EEE waste; and to promote environmental responsibility.
iv CF-5212/CF-5222 User and Installation Guide April 25, 2017
Table of Contents Table of Contents 1 Document Scope and Purpose .............................................................................................. 1 2 Overview ................................................................................................................................... 7 2.1 Features .......................................................................................................................... 8 2.2 Package Contents ..........................................
Table of Contents 9.5 9.6 9.7 Camera Tab .................................................................................................................. 76 Picture Adjustment ................................................................................................... 81 Advanced Picture Settings ....................................................................................... 82 IR Function ..................................................................................................
Table of Contents List of Figures Figure 1: IOI HD Analytic Fixed IP Camera ............................................................................................... 7 Figure 2: Package Contents....................................................................................................................... 9 Figure 3: CF-5212/CF-5222 Camera Dimensions ...................................................................................
Table of Contents Figure 54: Factory Default Screen ........................................................................................................... 66 Figure 55: Partial Restore Screen ............................................................................................................ 67 Figure 56: Software Version Screen ........................................................................................................ 67 Figure 57: Software Upgrade Screen ........................
Table of Contents Figure 110: Quasar Player Installation Wizard ...................................................................................... 116 Figure 111: Quasar Player Installation Completed ................................................................................ 116 Figure 112: Back Focus Adjustment ...................................................................................................... 119 Figure 113: Typical Spring Clamp Terminal Block .................................
x CF-5212/CF-5222 User and Installation Guide April 25, 2017
Document Scope and Purpose 1 Document Scope and Purpose The purpose of this document is to provide instructions and installation procedures for physically connecting the CF-5212/CF-5222 unit. After completing the physical installation, additional setup and configurations are required before video analysis and detection can commence. Note: This document is intended for use by technical users who have a basic understanding of CCTV camera/video equipment and LAN/WAN network connections.
Document Scope and Purpose A Warning is a precautionary message that indicates a procedure or condition where there are potential hazards of personal injury or death. Avertissement est un message préventif indiquant qu'une procédure ou condition présente un risque potentiel de blessure ou de mort. A Caution is a precautionary message that indicates a procedure or condition where there are potential hazards of permanent damage to the equipment and or loss of data.
Document Scope and Purpose General Cautions and Warnings This section contains information that indicates a procedure or condition where there are potential hazards. SAVE ALL SAFETY AND OPERATING INSTRUCTIONS FOR FUTURE USE. Although the unit is designed and manufactured in compliance with all applicable safety standards, certain hazards are present during the installation of this equipment.
Document Scope and Purpose Warning: Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt. Do not aim the camera lens at strong light, such as the sun or an incandescent lamp, which can seriously damage the camera.
Document Scope and Purpose Site Preparation There are several requirements that should be properly addressed prior to installation at the site. The following specifications are requirements for proper installation and operation of the unit: Ambient Environment Conditions: Avoid positioning the unit near heaters or heating system outputs. Avoid exposure to direct sunlight.
6 CF-5212/CF-5222 User and Installation Guide April 25, 2017
Overview 2 Overview The IOI HD CF-5212/CF-5222 fixed cameras provide real-time, H.264 and MJPEG streaming video with the highest quality image and video analytics. Featuring a compact, sophisticated and aesthetic mechanical design, the lightweight CF-5212 and CF-5222 cameras are easy to install and operate. Two models are available: The CF-5212 is a 1.3 megapixel, HD 720p device. The CF-5222 is a 2.1 megapixel, Full HD 1080p device The cameras include a DC-Iris lens with True Day/Night performance.
Overview 2.
Overview 2.2 Package Contents Before proceeding, check that the box contains the items listed here. If any item is missing or has defects, do not install or operate the product. Contact your dealer for assistance. IP Fixed Analytic Camera Back focus adjuster Quick Installation Guide CD with bundled software and documentation 1x 3-pin male connector Figure 2: Package Contents Related Documentation IOI HD CF-5212/CF-5222 Quick Installation Guide DNA 2.
10 CF-5212/CF-5222 User and Installation Guide April 25, 2017
Introduction to the CF-5212/CF-5222 IP Fixed Camera 3 Introduction to the CF-5212/CF-5222 IP Fixed Camera This chapter provides information about the camera hardware for reference before installation. The connectors included on the camera’s connector panel are described. Camera Dimensions Camera Connections Connecting the Unit to the Network 3.1 Camera Dimensions The mechanical dimensions of a CF-5212/CF-5222 Fixed IP Camera are shown below. Figure 3: CF-5212/CF-5222 Camera Dimensions 3.
Introduction to the CF-5212/CF-5222 IP Fixed Camera ID Connector Name 1 2 3 Line Out Line In/Mic In 4 5 6 Pin Number/ Connector Type Definition Network/PoE RJ45, Network LEDs Video SD BNC Audio out Audio in 10/100 Mbps Ethernet/PoE Analog video microSD card slot DC 12V/AC 24V 1 – Power (+) 2 – Reserved 3 – GND (-) 1- Power (+) 2- Earth GND 3- Power (-) 1 - Output (+) 2 - Output (-) 7 24V AC Alarm output Alarm input Auto Iris 5 – GND 6 - D (-) 7 - D (+) DC iris lens connector Grounding
Introduction to the CF-5212/CF-5222 IP Fixed Camera Note: An Ethernet crossover cable can be used when connecting the CF-5212/CF-5222 camera directly to the PC. Connecting Power to the Camera The camera can be powered by Power over Ethernet (PoE) or by an external 12VDC or 24VAC adaptor (not included in the package). If using an external power supply, connect the power leads or three-pin power terminal block to the power supply.
14 CF-5212/CF-5222 User and Installation Guide April 25, 2017
System Requirements 4 System Requirements To access the camera via a web browser, ensure that your PC has the proper network connection and meets system requirements as described below. Item Minimum System Requirement Personal Computer Minimum: Intel® Core™ i5-2430M @ 2.4 GHz, 4GB RAM Recommended: Intel® Core™ i7-870 @ 2.93 GHz, 8GB RAM Windows XP, 7, 8, 8.
16 CF-5212/CF-5222 User and Installation Guide April 25, 2017
Installation 5 Installation Follow the instructions below for indoor and outdoor installation of the camera. Related Links Outdoor Installation Lens Mounting Initial Camera Configuration Mounting Instructions 5.1 Outdoor Installation Read the instructions provided in this chapter thoroughly before installing the camera.
Installation In a similar manner, the shorter the focal length is, the smaller the size of each object will be, while the captured scene will become wider. Note: Use a short focal length to cover a wide area and detect objects at close distances. Use a long focal length to achieve greater detection distances while narrowing the Field of View.
Installation 3. Align the lens threads into the lens mount and screw in the lens. Figure 6: Installed C-CS Mount 4. If your lens has a DC auto iris, plug the auto iris cable from the lens assembly into the AUTO IRIS port of the camera. Figure 7: Auto Iris Port Connection Tip: If there are problems focusing, it might be necessary adjust the back focus. See Back Focus Adjustment (page 119).
Installation 5.3 Initial Camera Configuration Caution: If you are using Latitude, we recommend that you configure the camera’s settings via the AdminCenter. This is because the camera’s web-based interface might be overwritten by Latitude settings. Refer to the Latitude online help for information regarding configuring camera settings. Attention: Si vous utilisez Latitude, nous vous conseillons de configurer les paramètres de la caméra via l'AdminCenter.
Installation Right-click the mouse and select the assigned IP address or click the Assign IP button to open the DNA Assign IP dialog box. Note: The camera default IP Address and the subnet mask IP Address are automatically supplied by the DHCP server. In the dialog box that is displayed, enter values for the IP Address, Gateway and Netmask. Click Update and wait for OK status to be displayed. Figure 9: DNA Assign IP Dialog Box Disconnect the Ethernet cable.
Installation 5.4 Mounting Instructions The following are mounting instructions for the CF-5212 and CF-5222 fixed IP cameras. Caution: To avoid damage from overheating or unit failure, assure that there is sufficient temperature regulation to support the unit’s requirements (cooling/heating). Operating temperature should be kept in the range -40° to 50°C (-40° to 122°F), with no more than 90% non-condensing humidity.
Installation i. Connect the cables and wiring to the camera. See Figure 4: CF-5212/CF-5222 Camera Input/Output Connections. Note: For outdoor installation, the camera must be installed in a protective housing such as a CF-X200-00 camera housing. See the figure below.
24 CF-5212/CF-5222 User and Installation Guide April 25, 2017
Using the DNA Utility to Search and Access the Camera 6 Using the DNA Utility to Search and Access the Camera The Discovery Network Assistant (DNA) is a user-friendly utility that is designed to easily discover and configure FLIR Professional Security edge devices on a network. The DNA tool has a simple user interface and does not require any installation. The software is provided as a single, standalone executable. It runs on any PC.
26 CF-5212/CF-5222 User and Installation Guide April 25, 2017
Configuring Communication Settings 7 Configuring Communication Settings To configure communication settings on the camera 1. Connect the camera to the network on the same VLAN/LAN as the workstation. 2. If the network supports the default, open the DNA utility by running dna.exe which can be found in the DNA utility folder in the supplied CD, or click the DNA icon . 3. In the DNA application, click the DNA button. 4. If the Windows Firewall is enabled, a security alert window pops up. 5.
Configuring Communication Settings 7. Right-click the camera whose network property is to be changed. From the context menu that opens, select Assign IP. The Assign IP dialog is displayed. Figure 14: DNA Assign IP – Use DHCP Dialog Box Tip: Record the camera’s MAC address for future reference. 8. To access DNA, do one of the following: For DHCP (not supported by Latitude): i. Select Use DHCP. Do not use for Latitude. ii. Click Update and wait for status.
Configuring Communication Settings 9. Right-click and select Web to directly access the camera via a web browser. The web browser opens on the unit’s Login dialog box. Figure 16: Login Dialog Box 10. Log into the unit with the default user name (“admin”) and password (“admin”). Note: 1. Both the user name and password are case-sensitive. 2. It is strongly advised that administrator’s password be altered for security reasons. 3.
Configuring Communication Settings If the existing certificate is old or invalid, the ActiveX installation may fail in systems that are not connected to the internet and therefore cannot update their security certificates. In this case, the Setup.exe file in the ActiveX folder on the supplied CD should be run. The user can then continue with the installation. Figure 18: ActiveX Installation Error Message 11. If a popup message appears for running the ActiveX add-on, click Allow.
Adjusting and Framing-Up the Camera View 8 Adjusting and Framing-Up the Camera View After the camera is connected to the network and running, it is necessary to frame-up the scene and adjust the camera settings to optimize the picture for the individual scenes. If Latitude is being used, consider scheduling different settings for changing ambient conditions throughout the day, week, month or seasons. To adjust and frame-up the camera view 1. After the unit’s web interface opens, adjust the zoom and focus.
32 CF-5212/CF-5222 User and Installation Guide April 25, 2017
Configuration and Operation 9 Configuration and Operation The IOI HD camera is provided with a browser-based configuration interface for video playback and recording. If FLIR’s Latitude VMS is used, many of the configurations and features of FLIR’s VMS provide additional configuration and automation options for the camera. This section includes the following information: Browser-Based View Introduction Live Screen System Tabs Streaming Tab Camera Tab Log Out 9.
Configuration and Operation The user interface displays the following information: The Navigation Bar is displayed in the center of the screen containing Live and Settings buttons. Live Button The Live screen opens by default when the camera logs on.
Configuration and Operation 9.2 Live Screen The camera’s Live screen is used to monitor live video. See Figure 19: Browser-Based User Interface (page 33). Double-clicking the Live window opens the Info dialog box, which displays key details about the video stream: Figure 20: Live Video Info Dialog Box To view the Live View screen in Fullscreen mode 1. Double-click the screen. The image is displayed in the entire monitor screen. To exit Fullscreen mode 1. Click CLOSE.
Configuration and Operation Snapshot Click this button to automatically save the JPEG snapshots in the specified location. The default location to save snapshots is: C:\.To change the storage location, refer to File Location. Note: When using Windows 8 OS, the storage location cannot be C:\. You must define a storage location that does not require Administrator privileges on the PC.
Configuration and Operation 9.3 System Tab The Settings tab in the Navigation Bar opens the sections in the sidebar that are used for configuring the camera. The sections available for configuration include System, Streaming, Camera, and Analytics. Note: The System screen is accessible only by the Administrator.
Configuration and Operation System Screen The System screen is used for entering the camera’s friendly name and date and time settings. Click the System tab in the sidebar. The System screen is displayed. Figure 23: System Screen The System screen includes the following fields: Host Name The host name is for camera identification. If the alarm function is enabled and is set to send an alarm message by Mail or FTP, the host name entered here is displayed in the alarm message. See Events Setup.
Configuration and Operation Sync with Computer Time Select this button to synchronize video date and time display with the PC. You can change the PC date and time in the respective text box. Manual The Administrator can set video date and time manually. Entry format should be identical with that displayed to the right of the text box. Sync with NTP Server Network Time Protocol (NTP) is an alternate way to synchronize the camera’s clock with an NTP server. Select Sync with NTP Server.
Configuration and Operation Admin Password Change the administrator’s password by entering the new password in both text boxes. The input characters/numbers are displayed as dots for security purposes. After clicking SAVE, the web browser asks the Administrator for the new password (maximum 14 digits). Note: The following characters are valid: A-Z, a-z, 0-9,!#$%&’-.@^_~. Add user The user name and passwords are limited to 14 characters. There is a maximum of 20 user accounts. To add a new user 1.
Configuration and Operation Figure 25: Edit User Account Dialog Box Click Save to modify the account credentials and privileges, or Close to discard changes. Streaming Authentication Setting From the drop-down list, select one of the following options: Disable – Do not use streaming authentication (default setting). Basic – A form of authentication that uses unencrypted base64 encoding. Basic Authentication should generally only be used where transport layer security, such as HTTPS, is provided.
Configuration and Operation To create a self-signed certificate Before a CA-issued certificate is obtained, users can first create and install a self-signed certificate. Under the Security category, click the HTTPS tab in the sidebar to display the following screen. Figure 26: HTTPS Screen – Create Self-Signed Certificate 1. On the HTTPS page, click CREATE under Create Self-Signed Certificate. The Create SelfSigned Certificate dialog box opens.
Configuration and Operation 2. Enter the information in the appropriate field. A definition of each of the required fields follows. Country – Enter a two-letter combination code to indicate the specific country in which the certificate will be used. For instance, type “US” to indicate United States. State or province – Enter the local administrative region. Locality – Enter other geographical information.
Configuration and Operation 6. Click UPLOAD to install the certificate, as seen in Figure 30. Figure 30: HTTPS Screen – Upload Signed Certificate To create a certificate request 1. Click CREATE CERTIFICATE REQUEST to create and submit a certificate request in order to obtain a signed certificate from a CA.
Configuration and Operation The Create Certificate Request dialog box opens. Figure 32: Create Certificate Request Dialog Box 2. Enter the information in the appropriate field. A definition of each of the required fields follows. Country – Enter a two-letter combination code to indicate the specific country in which the certificate will be used. For instance, type “US” to indicate United States. State or province – Enter the local administrative region.
Configuration and Operation 4. To view details of the Certificate Request, click PROPERTIES below the Subject field. The Certificate Request Properties dialog box opens. If you want to remove the certificate, click REMOVE. Figure 34: Certificate Request Properties Dialog Box 5. Copy the PEM-formatted request and send it to your CA. Note: The self-signed certificate does not provide the same level of security as a CA-issued certificate.
Configuration and Operation IP Filter The IP filter restricts access to the camera by denying/allowing specific IP addresses. Click the IP filter tab under the category Security in the sidebar to display the following page. Figure 35: IP Filter Screen To enable the IP filter 1. Check the box to enable the IP filter function. Once enabled, the listed IP addresses (IPv4) are allowed or denied access to the camera. 2. Select Allow or Deny from the drop-down list. 3.
Configuration and Operation IEEE 802.1X The camera is allowed to access a network protected by 802.1X/EAPOL (Extensible Authentication Protocol over LAN). Users must contact the network administrator to obtain certificates, user IDs, and passwords. Figure 36: IEEE 802.1X/EAP-TLS Screen CA Certificate The CA certificate is created by the Certificate Authority for the purpose of validating itself. Click Browse to locate the file and UPLOAD to upload the certificate to check the server’s identity.
Configuration and Operation Network From the System screen, click the Network tab. The following screens are available from the Network tab: Basic QoS SNMP UPnP DDNS Mail FTP Basic The Basic screen is used to configure the camera’s basic network settings. Figure 37: Network > Basic Screen It is possible to connect to the camera with either fixed or dynamic (DHCP) IP address.
Configuration and Operation Get IP address automatically If you select Get IP address automatically, you can use the DNA utility, which is provided in the supplied CD, to obtain the IP address from a DHCP server on the network. See Using the DNA Utility to Search and Access the Camera. Note: For future reference, record the camera’s MAC address, which is found on the camera label. Use fixed IP address The camera’s default setting is Use fixed IP address.
Configuration and Operation Note: Be sure to assign a different port number for each service mentioned above. Click SAVE to save the settings. IPv6 Address Configuration IPv6 is not supported. QoS QoS (Quality of Service) provides differentiated service levels for different types of traffic packets and guarantees delivery of priority services during periods of network congestion.
Configuration and Operation Note: To enable this function, make sure the switches/routers in the network support QoS. SNMP Settings The Simple Network Management Protocol (SNMP) enables the camera to be monitored and managed remotely by the network management system. SNMP configuration settings are entered in the System > Network > SNMP screen. Figure 39: SNMP Settings Screen SNMP v1/v2 Enable SNMP v1 or Enable SNMP v2 – Select the version of SNMP (v1 or v2) to use by checking the relevant box.
Configuration and Operation SNMP v3 SNMP v3 provides important security features including: Confidentiality – Encryption of packets to prevent snooping by an unauthorized source. Integrity – Message integrity to ensure that a packet has not been tampered with in transit including an optional packet replay protection mechanism. Authentication – To verify that the message is from a valid source.
Configuration and Operation UPnP Settings Enable UPnP – If UPnP is enabled and a camera is discovered on the LAN, the icon of the connected camera appears in My Network Places, allowing direct access, as seen below. Figure 41: Direct Access to Camera with UPnP Enabled Note: To enable this function, make sure the UPnP component is installed on your computer. Refer to Install UPnP Components for the Windows 7, 8, 8.1, and 10 procedure.
Configuration and Operation DDNS Dynamic Domain Name System (DDNS) allows a host name to be constantly synchronized with a dynamic IP address. This permits those using a dynamic IP address to be accessed by a static domain name. DDNS configuration settings are entered in the System > Network > DDNS screen: Figure 42: DDNS Screen To use DDNS 1. Select the Enable DDNS checkbox. 2. From the Provider drop-down list, select a DDNS host provider name. 3.
Configuration and Operation Mail Simple Mail Transfer Protocol (SMTP) is a protocol for sending e-mail messages between servers. It is a relatively simple, text-based protocol, where a text message is transferred to one or more specified recipients. The Administrator can send an e-mail via Simple Mail Transfer Protocol (SMTP) when an alarm is triggered. E-mail notifications are set by selecting the checkbox for an e-mail-related triggered action on the IO and Network Failure Detection screens.
Configuration and Operation FTP The Administrator can send an alarm message to one or two File Transfer Protocol (FTP) sites when motion is detected. FTP notifications are set by selecting the checkbox for an FTP-related triggered action on the IO and Network Failure Detection screens. For each server, enter the server IP address, server port number, user name, password, and remote folder path.
Configuration and Operation Events Setup The Events Setup tab includes the following screens: IO Network Failure Detection IO The IO screen is used to control input and output alarms and messages, which are generated when an event is recognized by the system. Figure 45: IO Screen Alarm Switch The Administrator can select from the following options: Select Off to disable an alarm. Select On to enable an alarm (default setting). Select By Schedule to set a schedule.
Configuration and Operation Alarm Type Select an alarm type (Normal close or Normal open) that corresponds to the alarm application. Normal open is the default setting. Click SAVE after configuring the settings. Alarm Output Define the normal alarm output signal as Normal Open or Normal Close, according to the current alarm application. Normal open is the default setting. Click SAVE after configuring the settings.
Configuration and Operation Select the Continuous image upload checkbox to upload an image by FTP for a defined period of time or while the trigger is active. Select one of the following options: To specify the length of time for the upload, select Upload for and enter the number of seconds in the text box. To upload while the trigger is active, select Upload while the trigger is active.
Configuration and Operation Click SAVE after configuring the settings. File Name File Name – Enter a file name in the field, for example image.jpg. The uploaded image’s file name format is set in this section. Select one that meets your requirements. Add date/time suffix (default setting) File name: imageYYMMDD_HHNNSS_XX.jpg Y: Year, M: Month, D: Day H: Hour, N: Minute, S: Second X: Sequence Number Add sequence number suffix (no maximum value) File name: imageXXXXXXX.
Configuration and Operation Detection Switch The Administrator can select from the following options: Select Off to disable an alarm (default setting). Select On to enable an alarm. Select By Schedule to set a schedule. Then click Please Select to select up to 10 schedules from the drop-down list that opens. The selected schedules are displayed in the Please Select text box. To set a schedule, open the Schedule tab. Click SAVE after configuring the settings.
Configuration and Operation Schedule The Schedule screen is used for setting schedules for the recording of events triggered in the Events Setup > IO and Events Setup > Network Failure Detection screens. The functions in this tab allow administrators to create customized schedules for the camera that uses this option. If a schedule exists, the administrator can apply that schedule to this camera using the available drop-down list. See Figure 49: Schedule Screen.
Configuration and Operation File Location From the File Location page, specify a storage location for snapshots and web recordings. The default setting is: C:\. After confirming the setting, click SAVE to save the snapshots and recordings in the designated location. Figure 50: File Location Screen Note: 1. Make sure the selected file path contains valid characters. 2. When using Windows 8 OS, the storage location cannot be C:\.
Configuration and Operation Maintenance Clicking the Maintenance tab in the System screen opens a drop-down menu with the following tabs: Log File User Factory Information Default Software Version Software Parameters Upgrade Log File Click Log file to view the system log file. The content of the file provides information about connections after system boot-up.
Configuration and Operation View User Privilege Click GET USER PRIVACY to view each user’s privileges. Figure 53: User Information – Get User Privacy In the screen above, the admin is granted privileges of I/O access, Camera control, Talk and Listen, and Analytics, which are the maximum privileges that can be granted. The user Joe has only I/O access privilege. Note: User credentials and privileges are set in the User screen (page 39). Factory Default The Factory default page is shown below.
Configuration and Operation Partial Restore Click PARTIAL RESTORE to restore the factory default settings of the camera system, but save the network settings. The system restarts in 30 seconds. Figure 55: Partial Restore Screen Analytics Restore Click ANALYTICS RESTORE to reset the analytic firmware. Note: Analytics firmware is stored in a separate file than the camera system firmware. To backup and restore the analytics firmware version, see Analytics > Backup & Restore.
Configuration and Operation Software Upgrade The Software Upgrade screen enables you to select a software file to upload. Figure 57: Software Upgrade Screen Note: 1. Make sure that the software upgrade file is available before performing a software upgrade. 2. Do not change the file name. If you change the upgrade file name, the system will fail to find the file. 3. Analytics firmware is stored in a separate file than the camera system software.
Configuration and Operation Parameters The Parameters screen displays all of the system’s parameter settings. Figure 58: Parameter Screen Note: Slide the sidebar located on the right of the screen to view the entire list of parameters. Import/Export From the Import/Export screen you can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the camera. Figure 59: Import/Export Screen Note: 1.
Configuration and Operation Warning: Do not unplug power while changing file names. Avertissement: Ne débranchez pas l'alimentation pendant la modification des noms de fichiers. To export a configuration file 1. Click EXPORT. An information bar opens. Figure 60: File Download Screen 2. Click Save. 3. Specify a location to save the configuration file. To import a configuration file 1. Click Browse to select the configuration file 2. Click UPLOAD. The file is uploaded to the camera.
Configuration and Operation 9.4 Streaming Tab Select the Streaming tab in the navigation bar at the top of the page to display the configurable video and audio selections in the sidebar. From the Streaming sidebar, the Administrator can configure a specific video resolution, video compression mode, video protocol, audio transmission mode, etc. Details of these settings are specified in the following sections.
Configuration and Operation GOV Settings Users can set the GOV length to determine the frame structure (I-frames and P-frames) in a video stream for saving bandwidth. The setting range is from 1 to 255. A longer GOV means decreasing the frequency of I-frames. The default setting is 30. Click SAVE to confirm the GOV setting. H.264 Profile The H.264 standard defines 21 sets of capabilities. These are referred to as profiles and they target specific classes of applications.
Configuration and Operation MJPEG Compression Setting A higher value implies higher bit rates and higher visual quality. The default setting of the MJPEG Q factor is 35. The setting range is from 1 to 45. Click SAVE to confirm the setting. H.264-1 Compression Setting The default setting of H.264 is 2074 kbps. The setting range is from 64 to 8192 kbps. Click SAVE to confirm the setting. Compression Information Setting Select the checkbox to display compression information on the Home page.
Configuration and Operation Video OCX protocol setting options include: RTP over UDP RTP over RTSP (TCP) RTSP over HTTP MJPEG over HTTP Multicast mode – Enter in each field all required data, including Multicast H.264 Video Address and Port, Multicast MJPEG Video Address, Multicast Audio Address, and Multicast TTL. The default Multicast TTL (time-to-live) setting is 1, which prevents multicast datagrams from being forwarded beyond a single sub-network. Click SAVE to confirm the settings.
Configuration and Operation Audio From the Audio screen you can select the Transmission Mode, Server Gain, Bit Rate, and enable or disable storage of the audio recording. Figure 65: Audio Screen Transmission Mode Full-duplex (Talk and listen simultaneously) – In the Full-duplex mode, the local and remote sites can communicate with each other simultaneously, i.e. both sites can speak and be heard at the same time.
Configuration and Operation 9.5 Camera Tab From the Camera tab, the administrator can adjust any of the camera settings from the following tabs: Exposure Picture Adjustment Advanced Picture Settings IR Function Misc. Figure 66: Camera Section Tabs Exposure Screen The Exposure screen is used to configure lens settings and exposure modes. The exposure is the amount of light received by the image sensor.
Configuration and Operation Caution: Using a slow shutter speed causes moving objects to be blurred. Attention: L'utilisation de vitesses d'obturation faibles peut rendre les objets en mouvement flous. To set the Exposure mode 1. From the Max Gain drop-down list in 3db steps from to 54dB. Increasing the gain lightens dark pictures resulting from low-level lighting. The default setting is 36dB. Caution: The noise level might increase if the gain level is set too high in low-light scenes.
Configuration and Operation WDR Multiple Shutter RSS – This setting is recommended when flickering occurs in indoor applications where fluorescent lighting is used. The shutter speed decreases in order to compensate for decreased ambient lighting. Figure 68: Multiple Shutter RSS Exposure Screen From the drop-down list, select Normal or WDR First. Normal – See explanation above. WDR First – See explanation above. From the Min Shutter Speed drop-down list, select a shutter speed.
Configuration and Operation Caution: Using a slow shutter speed causes moving objects to be blurred. Attention: L'utilisation de vitesses d'obturation faibles peut rendre les objets en mouvement flous. To set the Exposure mode 1. From the Auto Mode Max Gain drop-down list, set the maximum gain in 3db steps from Off to 54dB. Increasing the gain lightens dark pictures resulting from low-level lighting. The default setting is 36dB.
Configuration and Operation Auto Shutter Min Shutter Speed PAL NTSC Auto Shutter Min Shutter Speed PAL NTSC 1/425 1/300 1/215 1/150 1/120 1/100 1/75 1/50 1/25 1/12 1/500 1/350 1/250 1/180 1/125 1/100 1/90 1/60 1/30 1/15 Shutter Priority – Select this mode to set a fixed exposure while other parameters can change. The shutter speed range is from 1/25 to 1/425 sec (PAL) to 1/30 to 1/500 sec (NTSC). The default setting is 1/25 (PAL) or 1/30 (NTSC).
Configuration and Operation Manual Mode Fixed Shutter Speeds PAL NTSC 1/10000 1/10000 1/3500 1/4000 1/2500 1/3000 1/1750 1/2000 1/1250 1/1500 1/1000 1/1000 1/600 1/725 1/425 1/500 1/300 1/350 1/215 1/250 1/150 1/180 1/120 1/125 1/100 1/100 1/75 1/90 1/50 1/60 1/25 1/30 1/12 1/15 From the Gain drop-down list, set the maximum gain in 3db steps from Off to 54dB. Increasing the gain lightens dark pictures resulting from low-level lighting. The default setting is 36dB. Click SET.
Configuration and Operation Contrast Camera image contrast level is adjustable. Select from a range of -13 to +12 in 1dB steps. The default setting is 0. Click SET to confirm the new setting. Saturation Camera image saturation level is adjustable. Select from a range of -12 to +13 in 1dB steps. The default setting is 0. Click SET to confirm the new setting. Hue Camera image hue level is adjustable: select from a range of +1 to +12 in 1dB steps. The default setting is 0.
Configuration and Operation Caution: Noise levels can be compromised when using the 2DNR/3DNR functions. Attention: Les niveaux de bruits peuvent être compromis avec les fonctions 2DNR/3DNR. Advanced Picture Settings with WDR Off When Advanced Picture Settings are disabled (configured as Off), in addition to 3DNR and 2DNR settings, the user can configure Backlight Compensation and Gamma WDR from this screen.
Configuration and Operation Smart – Smart mode enhances monochrome/Night mode stability when IR illumination is dominant and keeps the camera from switching between Day and Night modes. In this mode, the IR Cut filter is on (i.e. monochrome/Night mode) when the IR LED illuminator also is activated. This prevents the camera from returning to color/Day mode. Click SET to confirm the new setting. Miscellaneous From the Misc. (Miscellaneous) tab, you can set the TV System and Shutter WDR. Figure 74: Misc.
Configuration and Operation 9.6 Analytics Tab The IOI HD camera includes a rich set of video analytic functionality embedded in its firmware. The Analytics tab contains menus for defining the camera’s Field of View depth and detection rules, including region entrance, loitering, tripwire crossover, fence trespass, unattended baggage, stopped vehicle, and object removal. Figure 77: Analytics > Manual Depth Screen In real-time, the camera sends notifications and alarms upon the occurrence of events.
Configuration and Operation Caution: The camera is disarmed when configuring Analytics. Detection will not take place until the camera is manually re-armed from the Home screen. Attention: La caméra est désactivée lors de la configuration d'Analytics. La détection n'aura lieu qu'après que la caméra soit réactivée depuis l'écran Accueil. Depth The Depth screen enables you define the perspective of the scene being monitored and to.
Configuration and Operation The Auto Calibration function automatically configures scene depth and calculates camera height, focal length, and tilt angle according to the scene depth. The system discovers people in the scene and configures human markers automatically. This function eliminates the time and effort required to manually add human markers.
Configuration and Operation 9. Select the Auto > Step 2: Verification tab. 10. Verify that the horizon, camera height, and human marker settings are correct. Note: If the results are unsatisfactory, run Auto Calibration again (follow Step #1 on-screen) or click MANUAL to manually configure the depth settings. 11. After finishing the Auto Configuration, click the MANUAL tab. 12. Select the Manual > Step 4: Verification tab to complete the depth configuration.
Configuration and Operation Follow the instructions in the Solo Setup tab to single-handedly setup the camera: Figure 80: Analytics > Depth > Solo Setup Instructions To perform a solo setup 1. Click the Solo Setup tab.
Configuration and Operation 2. On the Solo Setup control keypad, click Start Recording camera’s Field of View. to record a view in the 3. Select a folder where to store the clip. Recording starts when the folder is selected. 4. Walk through various locations across the vertical axis of the camera’s Field of View in order to place ground and height markers and guidelines in the clip. 5. Click Stop Recording . 6. Click Step 1: Ground & Height and follow the instructions. 7.
Configuration and Operation Configuring Ground and Height Settings If you are not performing a solo setup, do the following: To configure ground and height settings 1. Click the Step 1: Ground & Height tab. The Step 1: Ground & Height screen opens. Figure 82: Analytics > Depth > Step 1: Ground & Height Screen 2. Follow the instructions on screen.
Configuration and Operation 3. Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings. 4. Click APPLY when finished or continue to the next step. Configuring Camera and Horizon Settings After completing Solo Setup or manually configuring ground and height settings, configure camera height and horizon settings. The Camera & Horizon tab is used for manually discovering people in the scene and configuring human markers.
Configuration and Operation 3. Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings. 4. Click APPLY when finished or continue to the next step. Configuring Advanced Depth Region Settings After configuring camera and horizon settings, configure advanced depth region settings. To configure advanced depth region settings 1. Click the Step 3: Advanced Depth Regions tab. The Step 3: Advanced Depth Regions screen opens.
Configuration and Operation 3. Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings. 4. Click APPLY when finished or continue to the next step. Settings Verification After configuring advanced depth region settings, verify your settings. To verify settings 1. Click the Step 4: Verification tab. The Step 4: Verification screen opens. Figure 88: Analytics > Depth > Step 4: Verification Screen 2. Follow the on-screen instructions to verify settings.
Configuration and Operation 3. Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings. 4. Click APPLY when finished. Rules The Rules tab enables you to define detection rules according to the type of detection you want to be notified about. By default, the Human or vehicle enter region rule is enabled.
Configuration and Operation To select a different rule, click the Human or vehicle enter region link. Select the rule from the dropdown list. Figure 91: Rules Drop-down List You can assign a name for the rule in the Name text box at the top of the screen. Select the Enable checkbox to activate the rule. Detection occurs when one or more detection rules are active, the camera is in Arm mode, and the scenario on the video (scene) fits the detection criterion specified.
Configuration and Operation The Advanced tab displays additional information for the rule. Click RESTORE DEFAULT to return to factory default settings. Figure 93: Analytics > Rules > Advanced Attributes Tab Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings.
Configuration and Operation Each automatic response definition includes the following three parameters: Triggering event, Actions and Schedule. Triggering event – Select the event that will start the automatic response.
Configuration and Operation To define a triggering event 1. Click ADD. A new Response is displayed in the top of the screen. 2. Select Enable to activate the Response. 3. From the Detection by type drop-down list, select one of the following detection types: Any detection (default), Intrusion detection, Vehicle Stopped, Unattended Object, Object Removed, Tripwire detection, Fence detection, or Loitering detection. The selection is displayed in the top of the screen. 4.
Configuration and Operation Note: Actions related to an analytic event that is defined in this screen are not affected by the status of the alarm switch configured on the Events Setup > IO screen. To define an action 1. From the Action drop-down list, select one of the following Actions. The selection is displayed at the top of the screen. Activate relay output Select Activate relay immediately or enter the number of seconds (1-999) in After x seconds drop-down list. Select the Relay number.
Configuration and Operation 2. To add an action, click ADD. The action is displayed in the Actions table. Figure 97: Responses > Actions Table 3. Repeat step 1 for each new Action. 4. To change the order of the Actions, click UP or DOWN. 5. To delete an action, select the Action and click DELETE. 6. Click APPLY when finished. 7. Schedule – Define when to monitor the triggering event occurrence. Figure 98: Responses > Schedule Tab To set a schedule 1. Do one of the following: Select Always.
Configuration and Operation Scheduled Actions (Sched. Actions Screen) The Sched. Actions screen is used for setting schedules for actions to be taken when an event occurs. Figure 99: Sched. Actions > Actions Tab Each scheduled action includes the following two parameters: Actions and Schedule Actions – Select the action to perform at the scheduled time To define an action 1.
Configuration and Operation Clear alarms Select Clear alarms immediately or enter the number of seconds (1-999) in After x seconds drop-down list. Click APPLY. Arm camera Select Arm immediately or enter the number of seconds (1-999) in After x seconds drop-down list. Click APPLY. Disarm camera Select Disarm immediately or enter the number of seconds (1-999) in After x seconds drop-down list. Click APPLY.
Configuration and Operation Schedule – Select when to perform the actions. Figure 101: Sched. Actions > Schedule Tab To set a schedule 1. Do one of the following: Select Always. Select Monitor event occurrences. In the From text box, enter the start date. In the To text box, enter the end date. If there is no end date, check No end date. From the Weekdays list, select the day of the week. In the Between text box, enter the hours during which the monitoring will occur. 2. Click APPLY.
Configuration and Operation On Screen Display The On Screen Display screen determines the information to be displayed on the video screen as an overlay on top of the video. The settings on this screen define the selection, alignment and color configuration of the various overlays that appear during normal monitoring, events and detection.
Configuration and Operation In the table, select the settings that you want to configure: In the Display column, select the checkbox to display the display item. In the Caption column, click Set to change the name of the display item. You cannot change the names Channel name, Date, Time and Status. In the Background color, Foreground color, Horizontal Align, and Vertical Align columns, clicking a field opens a drop-down list. Select one of the options from the drop-down list.
Configuration and Operation Refer to the HTML Edition Units User’s Guide for detailed instructions on configuring these settings. Backup & Restore The Backup & Restore screen enables you to create backup files of the unit’s analytics settings and to restore them. Figure 104: Analytics > Backup & Restore Screen To back up the analytic firmware file 1. Click BACKUP. To restore the analytic firmware file 1. Do one of the following: To restore factory defaults, select To factory defaults.
Configuration and Operation 9.7 Log Out Select the Log Out link in the navigation bar to close the session. The following message appears: Figure 105: Logout Message To return to the application, click Login. The Login dialog box opens. See Figure 16: Login Dialog Box.
Appendices 10 Appendices Technical Specifications Internet Security Settings Install UPnP Components Installing and Deleting the Web Player Deleting Temporary Internet Files Back Focus Adjustment Connecting Wires to a Spring Clamp Terminal Block Mounting and Lens Accessories April 25, 2017 CF-5212/CF-5222 User and Installation Guide 109
Appendices A.1. Technical Specifications Camera Image Sensor Effective Pixels Shutter Speed Sensitivity (w/ analytics) Color Mode Night Mode Enclosure CF-5212 CF-5222 1/3” Progressive 1.3MP 1/2.8” Progressive 2.1MP CMOS CMOS 1600 x 896 1920 x 1080 1/1.5 to 1/10,000 (PAL) 1 to 1/10,000 (NTSC) 0.1 lux @ F1.4 @ 15 FPS, 0.2 lux @ F1.4@ 15 FPS, 36dB max. gain 36dB max. gain 0.05 lux @ F1.4 @ 15 FPS, 0.1 lux @ F1.4@ 15 FPS, 36dB max. gain 36dB max.
Appendices Operation Two-way Audio Compression Connections Input Alarm Output Event Notification Languages Audio MicroSD Card Recording Network Interface Protocols Password Levels Security Firmware Upgrade Operating Systems Internet Browser User Accounts Line out and Line in/Mic-in G.711/G.
Appendices A.2. Internet Security Settings If ActiveX control installation is blocked, either set Internet security level to default or change ActiveX controls and plug-in settings. To set the default Internet security level 1. Start Internet Explorer (IE). 2. From the Command Bar toolbar, select Tools and select Internet Options from the menu that appears. Figure 106: Command Bar Toolbar – Select Internet Options 3. In the Internet Options window that appears, select the Security tab. 4.
Appendices ActiveX Controls and Plug-in Settings To create a custom level 1. Start Internet Explorer (IE). 2. From the Command Bar toolbar, select Tools and select Internet Options from the menu that appears. Figure 108: Command Bar Toolbar – Internet Options 3. In the Internet Options window that appears, select the Security tab. 4. If not already selected, select , then select Custom Level. 5.
Appendices A.3. Install UPnP Components Follow the instructions below to enable UPnP so that the camera can be discovered and displayed in Network locations under Other Devices: To enable UPnP discovery in Windows 7, 8, 8.1, and 10 1. Click (Start) and select Control Panel. 2. Click Network and Internet. 3. Click Network and Sharing Center. 4. Click Change advanced sharing settings.
Appendices 5. Expand the Home or Work node, select Turn on network discovery. 6. Click Save Changes. Note: Network discovery requires that the DNS Client, Function Discovery Resource Publication, SSDP Discovery, and UPnP Device Host services are started, that network discovery is allowed to communicate through Windows Firewall, and that other firewalls are not interfering with network discovery. To check that the UPnP Device Host services are running 1.
Appendices A.4. Installing and Deleting the Web Player The Quasar Player enables you to view the camera’s user interface. If this is a first-time installation of the camera, the Quasar Player installation wizard opens after accessing the camera. Figure 110: Quasar Player Installation Wizard To install the Quasar Player 1. Click Next. The Player is installed. 1. Click Finish when the next screen opens. The installation is completed. Quasar Player is displayed in the list of installed programs.
Appendices 3. On the banner bar, click Uninstall. 4. If prompted to confirm the Uninstall, click Yes. After deleting the previous player file, you must clear your computer’s cache memory. To clear your computer’s cache memory 1. In the Control Panel, click Internet Options. The Internet Properties dialog box opens. 2. From the Browsing History section, click Delete. The Delete Browsing History dialog box opens. 3.
Appendices A.5. Deleting Temporary Internet Files To improve browser performance, it is recommended to clean up all of the temporary Internet files. To delete temporary Internet files 1. In Internet Explorer (IE), from the Command Bar toolbar, click Tools and select Internet Options from the menu that appears. 2. In the General tab in the Internet Options dialog box, click Delete. 3. In the Delete Browser History dialog box that appears, select Temporary Internet files.
Appendices A.6. Back Focus Adjustment When to adjust back focus Back focus refers to the distance from the rear lens element to the camera focal plane. In most cases, it is required to adjust back focus only when the camera’s lens cannot hold focus throughout its zoom range. If the focus cannot be achieved within the zoom range, you may need to adjust the back focus.
Appendices A.7. Connecting Wires to a Spring Clamp Terminal Block The unit is delivered with a 3-pin terminal block connector. The terminal block enables you to connect power wires to the unit. Figure 113: Typical Spring Clamp Terminal Block To connect a wire to the spring clamp terminal block 1. Strip the insulation from the end of each wire that is to be connected to the terminal block. Approximately 1 cm (2.54”) of wire should be exposed. 2.
Appendices A.8. Mounting and Lens Accessories The following mounting accessories are available from FLIR for installation of your IOI HD CF-5212/CF-5222 Fixed IP Camera. For more information on available options, contact your FLIR sales representative or visit www.FLIR.com/security to request details on where to get the accessories you need.
FLIR Systems, Inc. 6769 Hollister Ave. Goleta, CA 93117 USA PH: +1 805.964.9797 PH: +1 877.773.3547 (Sales) PH: +1 888.747.3547 (Support) FX: +1 805.685.2711 www.FLIR.com/security Corporate Headquarters FLIR Systems, Inc. 27700 SW Parkway Ave. Wilsonville, OR 97070 USA PH: +1 503.498.3547 FX: +1 503.498.
