Instruction Manual

ManualsBrandsFlir ManualsElectronics16CH Full HD NVR with 4 PoE Ports, 2TB

100

Table Of Contents

Basic Setup
- 1. Connect the Cameras
- 2. Connect a Monitor
- 3. Connect the Mouse
- 4. Connect the Ethernet Cable
- 5. Connect the Power Adapters
Front Panel
Rear Panel
Getting Started
Remote Control
- Mouse Control
Using the System
- Password
- On-Screen Display
- Using the Quick Menu
  - Adjusting Color Settings
- Using the Navigation Bar
- Using the Camera Toolbar
- Using the Virtual Keyboard
Setting the Time
Recording
Search (Playback)
- Playing Back Video from the Hard Drive
- Playback Controls
Backup
- Formatting the USB Device
- Backing up Video
- Using Video Clip Backup
- Viewing Backup Files
Using the Main Menu
- Info
- Setting
- Device Search
- Advanced
- Shutdown
FLIR SyncroIP NVR Central Management Software
- System Requirements
- Prerequisites
- Installing FLIR SyncroIP NVR CMS
- Adding a NVR from the local area network (LAN)
- Adding a NVR using a DDNS address
  - CMS Live Viewing Overview
- Using Alarm Rec (Event Search)
- Using Playback Mode
  - Playback Controls
- Configuring Monitoring Tasks and Projects
- Using E-Map
  - Configuring E-Map
  - Opening Cameras from E-Map
- Configuring the CMS
  - Configuring CMS Options
  - Changing the CMS Admin Password
- Adding User Accounts to the CMS
- Multi-Monitor Support
  - Opening Cameras in Secondary Monitors
  - Managing Secondary Monitors
Remote Viewing on Internet Explorer
- Prerequisites
  - IE Live Display Overview
  - Using Search Mode in IE (Playback)
    - Playback Controls
Mobile Connectivity
- iPhone
- iPad
- Android Phones
- Android Tablets
Appendix A: System Specifications
Appendix B: Setting up Remote Viewing
- What Do I Need?
- How Do I Find My IP and MAC addresses?
  - Finding Your External IP Address
- How Do I Enable Port Forwarding?
Appendix C: Auto Port Forwarding Wizard
- Installation
  - Obtaining Your Router Model Number and Version
- Configuration
Appendix D: Setting Up DDNS Service
- How Do I Enable DDNS On My System?
- Connecting to your system using DDNS
  - CMS Software or Mobile Apps
  - Internet Explorer
Appendix E: Remote Firmware Upgrade
- Installing a Firmware Upgrade Over the LAN
- Installing a Firmware Upgrade Over the Internet
Appendix F: Hard Drive Installation
- Installing a Hard Drive
- Removing the Hard Drive
- Formatting the Hard Drive
Appendix G: Connecting an External Monitor
Troubleshooting

Appendix A: System Specifications

APPENDIX A: SYSTEM SPECIFICATIONS

System

Inputs/Outputs

Display

Recording

Main Processor Dual-core embedded processor

Operating System Embedded LINUX

Pentaplex Operation Simultaneous View, Record, Playback, Backup, and Remote Monitoring

IP Camera Input 4 channel / 8 channel / 16 channel

Power over Ethernet

(PoE)

4 integrated PoE ports

Audio 1 channel input (BNC), 1 channel output (BNC)

PTZ RS-485, supports Pelco-D and Pelco-P

USB 2 ports

Alarm Input 4 Channel / 8 Channel / 16 Channel

Relay Out 3 Channel

Interface 1 HDMI, 1 VGA, 1 BNC

Resolution 1920×1080, 1280×1024, 1280×720, 1024×768

Display Split 1/4, 1/4/8, 1/4/8/9/16

OSD Camera Title, Time, Camera Lock, Motion Detection, Recording Status

Compression H.264

Resolution 1080P (1920×1080) / 720P (1280×720) / D1 (704×576/704×480)

Record Rate 480fps@D1, 240fps@720P, 120fps@1080P

Bit Rate 32Mbps

Record Mode High Quality Stream/Sub-Stream Recording: Manual, Schedule, Motion Detection,

Alarm

Record Interval 1~120 min (default: 60 min), Pre-record: 1~30 sec, Post-record: 10~300 sec