Instruction Manual
Table Of Contents
- 1 Important Safeguards
- 2 M3100E Series Features
- 3 Getting Started (M3100E Series)
- 4 Front Panel (M3100E Series)
- 5 Rear Panel (M3100E Series)
- 6 Basic Setup (M3100E Series)
- 6.1 Step 1: Connect the BNC Cameras
- 6.2 Step 2: Connect the Mouse
- 6.3 Step 3: Connect the Ethernet Cable
- 6.4 Step 4: Connect the Monitor
- 6.5 Step 5: Connect the Power Adapter and Power on the DVR
- 6.6 Step 6: Upgrade Firmware to Latest Version (if Available)
- 6.7 Step 7: Verify Camera Image
- 6.8 Step 8: Set the Time
- 6.9 Default System Password & Port Numbers
- 6.10 Quick Access to System Information
- 7 About MPX
- 8 Mouse Control
- 9 Remote Control
- 10 Using the System
- 11 Setting The Time
- 12 Recording
- 13 Search (Playback)
- 14 Backup
- 15 Managing Passwords and User Accounts
- 16 Using the Main Menu
- 16.1 Camera
- 16.2 Info
- 16.3 Setting
- 16.3.1 Network
- 16.3.2 Selecting DHCP or Static IP Address (TCP/IP)
- 16.3.3 Configuring System Ports (Connection)
- 16.3.4 Configuring DDNS Settings
- 16.3.5 Configuring Email Alerts
- 16.3.6 Event
- 16.3.7 Configuring Motion Detection
- 16.3.8 Configuring Video Loss Settings
- 16.3.9 Configuring Hard Drive Warnings
- 16.3.10 Configuring Network Warnings
- 16.3.11 Storage
- 16.3.12 Configuring the Video Recording Schedule
- 16.3.13 Configuring Pre-Recording
- 16.3.14 Configuring the Snapshot Schedule
- 16.3.15 Configuring Holidays
- 16.3.16 Formatting the Hard Drive
- 16.3.17 Configuring Hard Drive Type
- 16.3.18 Configuring General System Settings
- 16.3.19 Setting the Monitor Resolution (Display)
- 16.3.20 Saving Your System Configuration to a USB Flash Drive
- 16.3.21 Setting the System to Factory Defaults
- 16.3.22 Upgrading Firmware from USB
- 16.4 Shutdown
- 17 Connecting to Your System Over the Internet on PC or Mac
- 18 Using FLIR Cloud™ Client for PC or Mac
- 19 Connecting to your System Using Smartphone or Tablet Apps
- 19.1 iPhone
- 19.1.1 Prerequisites
- 19.1.2 Connecting to your System on iPhone
- 19.1.3 Live View Interface
- 19.1.4 Controlling PTZ Cameras
- 19.1.5 Viewing Snapshots and Videos with Local Files
- 19.1.6 Using Playback Mode on iPhone
- 19.1.7 Enabling Push Notifications
- 19.1.8 Using the Event List
- 19.1.9 Using Favorites
- 19.1.10 Using the E-Map
- 19.1.11 Device Manager
- 19.1.12 Adding Devices Using an IP or DDNS Address (Advanced)
- 19.2 iPad
- 19.2.1 Prerequisites
- 19.2.2 Connecting to your system on an iPad
- 19.2.3 Live View Interface
- 19.2.4 Controlling PTZ Cameras
- 19.2.5 Using Playback Mode on iPad
- 19.2.6 Using Local File to View Manual Recordings
- 19.2.7 Enabling Push Notifications
- 19.2.8 Using the Event List
- 19.2.9 Using Favorites
- 19.2.10 Using the E-Map
- 19.2.11 Using the Device Manager
- 19.2.12 Adding Devices Using an IP or DDNS Address (Advanced)
- 19.3 Android
- 19.3.1 Prerequisites
- 19.3.2 Connecting to your System on Android
- 19.3.3 Live View Interface
- 19.3.4 Controlling PTZ Cameras
- 19.3.5 Viewing Snapshots and Videos with Local Files
- 19.3.6 Using Playback Mode on Android
- 19.3.7 Enabling Push Notifications
- 19.3.8 Using the Event List
- 19.3.9 Using Favorites
- 19.3.10 Using the E-Map
- 19.3.11 Device Manager
- 19.3.12 Adding Devices Using an IP or DDNS Address (Advanced)
- 19.1 iPhone
- 20 DDNS Setup (Advanced)
- 21 Connecting a PTZ Camera (M3100E Series)
- 22 M3100E Series Hard Drive Installation
- 23 Troubleshooting
- 24 M3100E Series System Specifications
- 25 Notices
Using the Main Menu16
2. Configure the following:
• EmailSchedule: Click Setup and select the days you want email alerts to be
enabled.
• Receiver: Enter the email address that will receive alerts.
• Sender: Enter the sender’s email address.
• Subject: Enter the subject line for the email alert.
• Interval: Enter the interval between alert emails.
• Health Enable: Check to enable health check emails. Health check emails will be
sent periodically to ensure that the system is functioning normally. If you enable
health check emails, enter the Interval in minutes below.
NOTE
You must enable the Snapshot option for motion detection on each camera you would to receive
a jpg image attachment of the camera image. For details, see 16.3.7 Configuring Motion Detec-
tion, page 55.
3. Click Test to send a test email.
4. Click OK to save settings.
If you want to use Gmail or Yahoo Mail:
1. Under Mail Select, select Gmail or Yahoo Mail.
2. Configure the following:
• Anonymous: Check if your server supports anonymous log ins. Otherwise, leave
this unchecked.
• User Name: Enter your Gmail or Yahoo Mail user name.
• Password: Enter your Gmail or Yahoo Mail password.
• Receiver: Enter the email address that will receive alerts.
• Sender: Enter the sender’s email address.
• Subject: Enter the subject line for the email alert.
NOTE
You must enable the Snapshot option for motion detection on each camera you would to receive
attachments. For details, see 16.3.7 Configuring Motion Detection, page 55.
• Event Interval: Enter the interval between alert emails.
• Health Enable: Check to enable health check emails. Health check emails will be
sent periodically to ensure that the system is functioning normally.
• Interval: Enter the interval in minutes for health check emails.
3. Click Test to send a test email.
4. Click OK to save settings.
NOTE
Gmail and Yahoo Mail are not supported by FLIR. Gmail and Yahoo Mail SMTP information may
change. Contact Google or Yahoo for support.
If you want to use your own email server (advanced):
1. Under Mail Select, select Custom.
#LX400028; r.27370/27370; en-US
54