Quick Connection Guide

PACKAGE CONTENTS:
Installing the Camera
Adjusting the Camera
A
A
Thermal Bullet Camera
T4350BS / T4390BT SERIES
Quick Connection Guide
B
B
• Use an appropriate low voltage power cable to prevent fire or electrical shock.
• If using DC power, make sure to follow the correct polarity as marked on the
power cable.
• Make sure to install the camera in an area that can support the camera
weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Be careful not to leave fingerprints on the camera’s infared optics. Clean only
with low pressure fresh water and a lens cloth.
• Camera is rated for outdoor use (IP66), but is not intended for submersion in
water.
Safety PrecautionsWeights & Dimensions Inserting the microSD Card (Optional)
C
Connecting the Camera
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Notice
1
2
3
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2015 FLIR Systems, Inc. All rights reserved.
T4350BS_T4390BT_SERIES_QCG_EN_R1
D
Use the included mounting template to mark holes
for the screws.
Drill holes for the mounting screws.
Connect cables as shown in the section “Connecting
the Camera”.
Mount the camera to the surface using the included
mounting screws (4x).
NOTE: Use the included drywall anchors if installing
into drywall.
1 x IP Bullet Camera 1 x Mounting Template
Quick Start Guides
1 x MPX Terminator
4 x Mounting Screws 4 x Drywall Anchors
Use the included Star key to loosen the adjustment
screw on the camera stand.
1. Loosen the lock screw to position the camera.
2. Tilt the camera on the stand up to 90°.
3. Rotate the camera around the stand.
Tighten the camera stand lock screw when finished.
10.6” / 270mm
4.3”
109mm
3.9” / 99mm
Weight
2.75lbs
1.25kg
For local recording, you can install a microSD card in the camera
up to 32GB. SanDisk™ or Kingston™ brand microSD cards are
recommended.
Loosen the screw on the back of the camera body and
open the access door.
NOTE: For details on configuring microSD recording, see the
Instruction Manual.
Insert a microSD card into
the microSD card slot.
Close the access door and
secure the screw.
A
B
C
Ethernet Port: Not used.
Power: Connect a 12V DC or 24V AC power source.
Video Out (BNC): Connect the camera to an analog DVR.
Ethernet Port: Install the MPX terminator.
When you power up the camera with the
MPX Terminator installed, the camera operates as an MPX camera.
Power: Connect a 12V DC or 24 AC power source (300mA or higher).
Video Out (BNC): Connect the camera to an FLIR MPX DVR. Video and
MPX camera control are supported over a standard coaxial cable.
A
B
C
D
For support, visit
Latest software and manuals available on
www.flir.com/security/support
www.flir.com/security/support
1 x Star Key
1 x RJ45 Waterproof Cap
1 x Power Pigtail
1
1
2
3
4 5
3
2
Drywall anchors (4x)
microSD card slot
Mounting screws (4x)
Ethernet Port: Connect the camera to a FLIR NVR or a router or switch on
your network using Cat5e or better Ethernet cable (not included). PoE Class
3 supported.
Power: Connect a 12V DC or 24V AC power source if you are not using PoE.
Video Out (BNC): Analog video output to a test monitor (optional).
Audio IO: See the Instruction Manual for details.
Alarm IO: 1Brown—ALARM_COM; 2Purple—ALARM_NO;
3Red—Alarm_IN1; 4Yellow—Alarm_IN2; Pink—ALARM_GND.
IP / PoE
MPX
Audio / Alarm (Optional)
Analog
1.
4.
1.
1.
2.
5.
2.
2.
3.
3.
3.
12V DC Power Input Polarity