Smart Water Detector Install Guide Guide d'installation du Smart Water Detector meetflo.
DESCRIPTION This Smart Water Detector provides valuable telemetry to help protect property from damage caused by water, temperature extremes and high humidity. The Detector should be installed in locations with high risk of exposure to water and/ or temperature/ humidity extremes (i.e. basements for weather-related events, under or near appliances or fixtures like dishwashers, water heaters, etc., and attics or crawl spaces for temperature).
GENERAL SPECIFICATIONS SPECIFICATIONS GENERALES Moisture Detection Base unit Remote Sensing Disc Leak Sensing Cable (920-006) Temperature Range -20 to 140 °F (-29 to 60 C) Temperature Accuracy 40 to 140 °F(4 to 60 C): ·: 2 °F (lC) -20 to 40 °F(-29 to 4 C): + 3 °F (LS C) Humidity Range: Oto 100% Relative Humidity (RH) Typical accuracy: 0-20 RH: ±5% 20-80: ±3% 80-100: ±5% Battery type CR123A Lithium Cell Battery Lifet 2 years Connectivity Wi-Fi network (WLAN connectivity/ IEEE 802.11 bgn, 2.
SETUP AND INSTALLATION CONFIGURATION ET INSTALLATION Prior to installation, the Flo By Moen App must be downloaded from the Apple App Store or Google Play Store and installed on a smartphone (iPhone or Android). After an account has been created and the user logged in, the Detector is ready for set-up. The diagrams on the following pages provide guidance on how to access and activate the Smart Water Detector's battery.
remote sensing disc (included with Detector) or the separate leak sensing cable accessory must be installed to enable leak detection. le cable de teledetection de fuite (non inclus) doit etre installe pour permettre la detection de fuite. OU The sensing disc is intended for small spaces, such as under fixtures or appliances. The leak sensing cable (sold separately) enables creation of a sensing line or ring that will indicate if water contacts any point along its length.
COMPONENTS COMPOSANTS 0 2 Primary Sensor Capteur principal 3 Remote Sensing Disc Disque de teledetection Wall Mount Base (mounting screw and self-adhesive backing included) Support mural (vis de montage et support autocollant inclus) 4 Flo By Moen™ Mobile App Application mobile Flo By Moen TM
INSTALLATION INSTRUCTIONS INSTRUCTIONS D'INSTALLATION 0 1 Uft Sensor from Base Lever le capteur du support View Sensor from Top Regarder le capteur de face 3 c::? (Q)_ 0 Hold base. Rotate top cover counter clockwise Tenir le support.
Battery Insulator /so/ant batterie Battery Batterie Review important internal components Examiner avec attention les composants internes Reset button (Used when re-pairing) Bouton de reinitialisation. 6 7 Pull insulator to remove-. Blue LED will start to flash Tirer l'isolant pour l'enlever. La LED bleue commencera clignoter.
Hold base. Rotate top cover clockwise Maintenir le support. Faire pivoter le couvercle superieur dans le sens des aiguilles d'une montre. t t Complete re-assembly. Make sure base and cover are completely joined. Refermer. S'assurer que la base et le couvercle sont completementjoints. Reinstall the wall mount base only if using the remote sensing disc or leak sensing cable Remettre en place le support mural si vous utilisez un disque ou un cable de teledetection.
LIMITED WARRANTY GARANTIE LIMITEE Flo Technologies, 3750 Robertson Blvd., Suite 202, Culver City, CA 90232, warrants to the owner of the enclosed Flo by Moen Device contained in this box ("Product" or "Device") will be free from defects in materials and workmanship for a period of one (1) year from the date of delivery following the original retail purchase (collectively, the "Warranty Period").
breach of this Limited Warranty. Any Product that has either been repaired or replaced under this Limited Warranty will be covered by the terms of this Limited Warranty for the longer of (a) ninety (90) days from the date of delivery of the repaired Product or replacement Product, or (b) the remaining Warranty Period. This Limited Warranty is transferable from the original purchaser to subsequent owners, but the Warranty Period will not be extended in duration or expanded in coverage for any such transfer.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT DECLARATION DE CONFORMITE FCC This equipment has been tested and found to comply with the FCC-regulated limits per CFR 47 Part 15 Subpart C. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Warning: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
LED PATTERNS LED Pattern Voyants LED Status Description Description ·oFF tteint Normal operation mode when powered. Mode de fonctionnement normal lorsqu'il est alimente. Blinking Blue Bleu clignotant Detector in pairing mode - device will be visible to mobile device SSID list. Detecteur en mode jumelage, l'appareil sera visible sur la liste des appareils mobiles. Blinking Blue/ Purple Bleu / Violet clignotant Finalizing pairing process. Finalisation du processus de jumelage.
CANADA, INDUSTRY CANADA (IC) NOTICES CANADA, AVIS D'INDUSTRY CANADA (IC) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.