Use and Care Manual

ManualsBrandsFlood ManualsExterior Wood Coatings1 Gal. Clear CWF Oil Penetrating Exterior Wood Stain

FLOOD CWF

-OIL Penetrating Oil Wood Finish

GENERAL DESCRIPTION PRODUCT DATA

RECOMMENDED SUBSTRATES

FEATURES / BENEFITS

Provides a natural oil-based finish that protects wood against

moisture and sun damage. Fortified with PENETROL

for excel-

lent penetration. Recommended for use on any properly pre-

pared exterior wood, including decks, fences, siding, railings, out-

door furniture and other wood surfaces. Apply to new, dry, pres-

sure-treated wood, uncoated new or weathered wood, or wood

previously stained or painted. Apply directly to weathered wood

previously finished with FLOOD CWF-OIL; other previous coat-

ings must be completely removed.

PRODUCT TYPE: Oil

VOLUME SOLIDS*: 56% +/- 2%

WEIGHT SOLIDS*: 61% +/- 2%

VOC: <350 g/L (2.9 lbs./gal.)

WEIGHT/GALLON*: 7.5 lbs. (3.4 kg) +/- 0.2 lbs. (91 g)

*Product data based on product FLD447

COVERAGE: One gallon (3.78 Liters) will normally cover 100 to 200

sq. ft. (9.3 to 18.6 sq. meters). Coverage will vary due to porosity and

texture of wood and application technique.

DRYING TIME: Normally dries to the touch in four hours when applied

in optimal temperatures of 50°F to 90°F (10°C to 32°C). Application in

high humidity or in temperatures below 50°F (10°C) may prolong drying

time. Allow 24 to 48 hours of drying time before light foot traffic and 72

hours before replacing furniture. Allow new stain to cure 30 days before

washing.

To Recoat: Wet-on-wet before first coat has dried

For Pedestrian Service: 24-48 hours

Drying times listed may vary depending on temperature, humidity, film

build, color and air movement.

CLEANUP: Clean brushes and tools with mineral spirits.

DISPOSAL: Contact your local environmental regulatory agency for

guidance on disposal of unused product. Do not pour down a drain or

storm sewer.

PERMISSIBLE TEMPERATURES DURING APPLICATION:

Material: 50 to 90ºF (10 to 32ºC)

Ambient: 50 to 90ºF (10 to 32ºC)

Substrate: 50 to 90ºF (10 to 32ºC)

FLASH POINT: 133ºF (56ºC)

TINTING AND BASE INFORMATION

FLD447 Natural

FLD448 Cedar

Refer to the appropriate color formula book, automatic tinting

equipment, and or computer color matching system for color

formulas and tinting instructions.

T.D. FLD447

Features Benefits

Solvent Borne Clear finish formula Restores rich, warm look of natural wood while providing protection against

with a hint of color damage from UV rays

Added Mildewcide package Provides a mildew resistant finish

Water repellant coating Protects wood from water damage

Fortified with PENETROL

Provides excellent penetration

Easy application Can also be applied with a garden sprayer

FLOOD

FLD447

Wood

Read Label and Material Safety Data Sheet prior to use. See other cautions on last page.

PACKAGING

1 - Gallon (3.78 L)

5 - Gallon (18.9 L)

Summary of content (2 pages)

PAGE 1
FLOOD® FLD447 ® FLOOD CWF®-OIL Penetrating Oil Wood Finish GENERAL DESCRIPTION PRODUCT DATA Provides a natural oil-based finish that protects wood against moisture and sun damage. Fortified with PENETROL® for excellent penetration. Recommended for use on any properly prepared exterior wood, including decks, fences, siding, railings, outdoor furniture and other wood surfaces. Apply to new, dry, pressure-treated wood, uncoated new or weathered wood, or wood previously stained or painted.
PAGE 2
FLOOD FLD447 FLOOD CWF-OIL Penetrating Oil Wood Finish GENERAL SURFACE PREPARATION Surface must be dry and clean. Remove all dust, dirt, mildew, oil, loose wood fibers and other contaminants. Use Wood Stripper to remove any previous coatings. Previous coatings must be completely removed. To ensure proper adhesion, weathered, dirty or mildewed surfaces should be cleaned with Wood Cleaner prior to applying product. After rinsing, allow wood to dry. Remove grade stamps or pencil marks by sanding.