MAINTENANCE MANUAL METAL CBU TYPES I, II, III, AND IV 1570 “F” SERIES A FLORENCE COMPANY 5935 CORPORATE DRIVE MANHATTAN, KANSAS 66503 Ph. 800-275-1747 Fax. 800-275-5081 www.auth-florence.
I II III IV INSTALLED HEIGHT TYPE I 62” TYPE II 62” TYPE III 62” TYPE IV 62” DEPTH 17-7/8” 17-7/8” 17-7/8” 17-7/8” WIDTH 30-1/2” 30-1/2” 30-1/2” 30-1/2” WEIGHT (WITHOUT PEDESTAL) 107 LBS 111 LBS 147 LBS 137 LBS WEIGHT (WITH PEDESTAL) 125 LBS 129 LBS 162 LBS 152 LBS QTY OF STANDARD COMPARTMENTS 8 12 16 13 QTY OF PARCEL COMPARTMENTS 2 1 2 1 PARCEL COMPARTMENT HEIGHT 10”, 13” 10” 10”, 13” 10” AF PART # 91196 REV B AF PART # 91196 REV B
TABLE OF CONTENTS DESCRIPTION PAGE REPLACEMENT OF MASTER LOADING DOOR HOLD OPEN MECHANISM REMOVAL OF INSERT ASSEMBLY REPLACEMENT OF MASTER LOADING DOOR REPLACEMENT OF HINGE ROD REPLACEMENT OF RIGHT SIDE PATRON COMPARTMENT DOOR REPLACEMENT OF ARROW LOCK DOOR REPLACEMENT OF RIGHT SIDE PARCEL DOOR REPLACEMENT OF LEFT SIDE PATRON COMPARTMENT DOOR REPLACEMENT OF LEFT SIDE PARCEL DOOR REPLACEMENT OF 910A PATRON LOCK REPLACEMENT OF ARROW LOCK REPLACEMENT OF ARROW LOCK LATCH/SLIDE HANDLE REPLACEMENT OF PARCEL LO
REPLACEMENT OF MASTER LOADING DOOR HOLD OPEN MECHANISM 1. 2. 3. 4. 5. 6. TYPES I, II, III AND IV OPEN MASTER LOADING DOORS TO DISENGAGE HOLD OPEN MECHANISM: REMOVE ONE (1) 86231 6-32 TORX HEAD SHOULDER SCREW 8.
REPLACEMENT OF MASTER LOADING DOOR HOLD OPEN MECHANISM 1. 91067 2/7. 5. 86265 86267 86231 (CUTAWAY VIEW) 86098 86279 4/6.
REMOVAL OF INSERT ASSEMBLY TYPES I, II, III AND IV 1. 2. 3. 4. 5. 6. OPEN MASTER LOADING DOORS DISENGAGE HOLD OPEN MECHANISMS (SEE INSTRUCTIONS PAGE 4) [FOR TYPES I, II] REMOVE EIGHT (8) 91123 8-32 TORX HEAD SCREWS FROM INSERT ASSEMBLY [FOR TYPES III, IV] REMOVE TWELVE (12) 91123 8-32 TORX HEAD SCREWS FROM INSERT ASSEMBLY 8. REPLACE FOUR (4) 91057 3/16” POP RIVETS AT BOTTOM OF SLIDE MECHANISM AND REPLACE BRACKET 9.
REMOVAL OF INSERT ASSEMBLY 2/9. 91057 4/8. 91262 3/7. 91602 91244 91604 91615 91003 91070 5. 91123 1.
REPLACEMENT OF MASTER LOADING DOOR TYPES I, II, III AND IV 1. 2. OPEN MASTER LOADING DOORS DISENGAGE HOLD OPEN MECHANISMS FROM TOP OF MASTER LOADING DOORS (SEE INSTRUCTIONS PAGE 4) 3. REMOVE INSERT ASSEMBLY (SEE INSTRUCTIONS PAGE 6) 4. CLOSE MASTER LOADING DOORS AND REMOVE FOUR (4) 86229 8-32 STAINLESS STEEL TORX HEAD SCREWS 5. REMOVE ONE (1) 91061 TOP FRAME BRACE EXPOSING MASTER LOADING DOOR HINGES 6. 8. REPLACE INSERT ASSEMBLY (SEE INSTRUCTIONS PAGE 6) 9.
REPLACEMENT OF MASTER LOADING DOOR 4. 5. 91061 2/3. 86229 7. 1. 6.
REPLACEMENT OF HINGE ROD TYPES I, II, III AND IV 1. 2. 3. OPEN MASTER LOADING DOOR 6. DISENGAGE HOLD OPEN MECHANISM FROM TOP OF MASTER LOADING DOOR (SEE INSTRUCTIONS PAGE 4) 7. COMPLETELY OPEN MASTER LOADING DOOR SO THAT THE HINGE PIN IS VISIBLE / AND OR COMPLETELY REMOVE INSERT ASSEMBLY (SEE INSTRUCTIONS PAGE 6) 8. 4. REMOVE ONE (1) 86455 10-32 HEX LOCK NUT 5.
REPLACEMENT OF HINGE ROD 86455 4. 2/8. 5. 1. 6. 91040 91127 91260 5.
REPLACEMENT OF RIGHT SIDE PATRON COMPARTMENT DOOR 1. 2. 3. 4. 5. TYPES I, II, III, AND IV OPEN MASTER LOADING DOOR 6. REPLACE HOLD OPEN MECHANISM (SEE INSTRUCTIONS PAGE 4) DISENGAGE HOLD OPEN MECHANISM FROM TOP OF MASTER LOADING DOOR (SEE INSTRUCTIONS PAGE 4) 7.
REPLACEMENT OF RIGHT SIDE PATRON COMPARTMENT DOOR 2/6. 1. 3/5. 91111 91108 4.
REPLACEMENT OF ARROW LOCK DOOR TYPES I, II, III AND IV 1. 2. OPEN MASTER LOADING DOOR DISENGAGE HOLD OPEN MECHANISM FROM TOP OF MASTER LOADING DOOR (SEE INSTRUCTIONS PAGE 4) 3. REMOVE HINGE ROD (SEE INSTRUCTIONS PAGE 10) 4. REPLACE COLLECTION DOOR 91118 FOR TYPES I, II, AND III, OR 91119 FOR TYPE IV 5. REINSTALL HINGE ROD (SEE INSTRUCTIONS PAGE 10) REQUIRED TOOLS 1/8” ROD PORTABLE DRILL HAMMER PLIERS 14 AF PART # 91196 REV B 6. REPLACE HOLD OPEN MECHANISM (SEE INSTRUCTIONS PAGE 4) 7.
REPLACEMENT OF ARROW LOCK DOOR 2/6. 1. 3/5. 91118 91119 4.
REPLACEMENT OF RIGHT SIDE PARCEL DOOR TYPES I, II, III AND IV 1. 2. OPEN MASTER LOADING DOOR 7. REPLACE PARCEL DOOR SPRING (SEE INSTRUCTIONS PAGE 30) DISENGAGE HOLD OPEN MECHANISM (SEE INSTRUCTIONS PAGE 4) 8. REPLACE HOLD OPEN MECHANISM (SEE INSTRUCTIONS PAGE 4) 9. INSTALL LOCK MECHANISM (SEE INSTRUCTIONS PAGE 28) 3. REMOVE PARCEL DOOR SPRING (SEE INSTRUCTIONS PAGE 30) 4. REMOVE HINGE ROD (SEE INSTRUCTIONS PAGE 10) 5. 6.
REPLACEMENT OF RIGHT SIDE PARCEL DOOR 2/8. 4/6. 1. 91250-1 5.
REPLACEMENT OF LEFT SIDE PATRON COMPARTMENT DOOR TYPES I, II, III, AND IV 1. COMPLETELY OPEN LEFT SIDE MASTER DOOR SO THAT THE HINGE ROD IS VISIBLE 2. REMOVE HINGE ROD (SEE INSTRUCTIONS PAGE 10) 3. REPLACE COMPARTMENT DOOR 91111 FOR TYPE I, II, AND III, OR 91108 FOR TYPE IV 4. REINSTALL HINGE ROD (SEE INSTRUCTIONS PAGE 10) 5.
REPLACEMENT OF LEFT SIDE PATRON COMPARTMENT DOOR 1. 91111 91108 2/4. 3.
REPLACEMENT OF LEFT SIDE PARCEL DOOR TYPES I AND III 1. COMPLETELY OPEN LEFT SIDE MASTER DOOR SO THAT THE HINGE ROD IS VISIBLE 2. REMOVE HINGE ROD (SEE INSTRUCTIONS PAGE 10) 3. REPLACE PARCEL DOOR 91257-1 4. REINSTALL HINGE ROD (SEE INSTRUCTIONS PAGE 10) 4. REPLACE PARCEL DOOR SPRING (SEE INSTRUCTIONS PAGE 30) 4.
REPLACEMENT OF LEFT SIDE PARCEL DOOR 1. 2/4. 91257-1 3.
REPLACEMENT OF PATRON LOCK TYPES I, II, III, AND IV 1. 2. 3. 4. 5.
REPLACEMENT OF PATRON LOCK 1.
REPLACEMENT OF ARROW LOCK TYPES I, II, III, AND IV 1. 2. OPEN ARROW LOCK DOOR REMOVE FOUR (4) 86091 10-32 LOCK NUTS AND 92303 PLATE - LOCK SUPPORT 3. REPLACE ARROW LOCK INTO POSITION 4. INSTALL 92303 PLATE - LOCK SUPPORT AS SHOWN 5.
REPLACEMENT OF ARROW LOCK 1. 86091 3/4. ARROW LOCK 2/5.
REPLACEMENT OF ARROW LOCK LATCH/SLIDE HANDLE 1. 2. 3. 4. 5. 6. TYPES I, II, III, AND IV REPLACE HANDLE ASSEMBLY REMOVE TWO (2) 84998SS 10-32 X .865 SHC SCREW 7. 8. REMOVE LATCH RELEASE BRACKET 91011 - REPLACE WITH NEW LATCH RELEASE BRACKET 9. OPEN BOTH MASTER DOORS REMOVE/REPLACE 91063 LOCK BRACKET - REPLACE TWO (2) 91057 POP RIVETS CHECK FOR FIT/FUNCTION REPLACE TWO (2) 91124 SHOULDER BUSHINGS ALIGN WITH MOUNTING HOLES AND REPLACE TWO (2) 84998SS 10-32 X .
REPLACEMENT OF ARROW LOCK LATCH/SLIDE HANDLE 1. 4. 91063 91057 84998SS 2/5. 7. 91011 91124 8. 3.
REPLACEMENT OF PARCEL LOCK ASSEMBLY TYPES I, II, III, AND IV 1. 2. OPEN PARCEL DOOR, #1P ON TYPE I, TYPE II, TYPE III AND TYPE IV AND / OR #2P ON TYPE I AND TYPE III. A. REMOVE OR REPLACE PARCEL LOCK COVER 91255 USING THREE (3) 84995 8-32 X .250 1-WAY TAMPERPROOF SCREW TO REMOVE/REPLACE ARROW LOCK: A. REMOVE FOUR (4) 86091 10-32 LOCK NUTS - REMOVE ARROW LOCK B.
REPLACEMENT OF PARCEL LOCK ASSEMBLY 91259 91255 2A. 2B. 1. M20658017TN90JJ 86091 91092 91099 86243 3A/B. 91610 91258 84995 4A/C. 4B/D. 91620 5/16-24 LOCK NUT 2D. 2C.
REPLACEMENT OF PARCEL DOOR SPRING TYPES I, II, III AND IV 1. 2. 3. OPEN MASTER LOADING DOOR PLACE ONE END OF PARCEL DOOR SPRING 86431 OVER THREADED POST ON PARCEL DOOR AND TIGHTEN ONE (1) 86092 8-32 LOCK NUT INSERT OPPOSITE END OF SPRING THROUGH ONE (1) 91128 8-32 X 0.
REPLACEMENT OF PARCEL DOOR SPRING 1. 91128 2. 86091 3.
REPLACEMENT OF SHELF TYPES I, II, III AND IV 1. 2. 3. OPEN MASTER LOADING DOORS WITH A HAMMER APPLY FORCE UNDERNEATH THE SHELF TO BE REMOVED, DISLODGING IT FROM THE METAL SNAPS HOLDING IT TO THE INSERT PANEL. LIFT AND PULL TOWARD FRONT OF CBU TO REPLACE THE SHELF, PLACE IT ABOVE THE METAL SNAPS, ALIGN IT FRONT TO BACK, AND APPLY FORCE WITH A HAMMER TO SNAP THE SHELF BACK INTO PLACE THIS PROCEEDURE WILL NOT WORK FOR THE SHELF ABOVE A PARCEL LOCKER.
REPLACEMENT OF SHELF (CUTAWAY VIEW) 86051 1. (CUTAWAY VIEW) 3. 2.
REPLACEMENT OF MASTER LOADING DOOR SLIDE MECHANISM 1. 2. TYPES I, II, III AND IV OPEN MASTER LOADING DOORS COMPLETELY REMOVE INSERT ASSEMBLY (SEE INSTRUCTIONS - PAGE 6) 3. DRILL OUT TWO (2) 86098 1/8” POP RIVETS AT TOP OF SLIDE MECHANISM AND REMOVE WEAR PLATE 4. DRILL OUT TWO (2) 86098 1/8” POP RIVETS NEAR ARROW LATCH AND REMOVE WEAR PLATE 5. REMOVE ARROW LATCH HANDLE (SEE INSTRUCTIONS PAGE 26) 6.
REPLACEMENT OF A MASTER LOADING DOOR SLIDE MECHANISM 2. 91106 91019 91086 1. 3. 86098 91037 4. 5.
REPLACEMENT OF PEDESTAL TYPES I, II, III AND IV 1. 2. OPEN MASTER LOADING DOORS 6. TO REPLACE CBU CABINET, REVERSE STEPS 1-4 REMOVE LEFT AND RIGHT SIDE 91079 FLOATING SHELVES, EXPOSING MOUNTING HOLES WARNING: 2 PEOPLE REQUIRED TO REMOVE CABINET FROM PEDESTAL, UNIT IS FRONT HEAVY. 3. REMOVE FOUR (4) 86089B 3/8-16 HEX NUTS AND FOUR (4) 86097 3/8” X .688 OD LOCK WASHERS 4. FROM UNDERNEATH UNIT, REMOVE FOUR (4) 86101 3/8-16 X 1.25 CARRIAGE BOLTS 5.
REPLACEMENT OF A PEDESTAL 6. 86084B 3. 86097 86101 4. 5. 1. 2.
Part# QTY Type 1 QTY Type 2 QTY Type 3 QTY Type 4 14707 BOLT-CARRIAGE 10-32 X 1.5 2 2 2 2 30807 CLIP-LOCK 10 13 18 14 30697 RIVET TUBULAR .125 X .250 SS 2 1 2 1 30997 RIVET TUBULAR .125 X .312 SS 2 1 2 1 84500 LABEL LOCK & KEY 1 1 1 1 84993 SCREW- 10-32 X .312 MCGARD 4 2 4 2 84994 SCREW- 10-32 X .375ONE WAY 4 2 4 2 84995 SCREW- 8-32 X .25 ONE WAY 2 1 2 1 84998SS 38 Description SCREW 10-32 X .
Part# QTY Type 1 QTY Type 2 QTY Type 3 91023 DOOR-COLLECTION 1 1 1 91027 SHELF-BTM. LEFT 1 1 1 1 91028 SHELF-BTM RT 1 1 1 1 91031 CROSSBAR-TOP RT 1 1 1 1 91032 CROSSBAR-BTM 2 2 2 2 91033 CROSSBAR-CTR.
Part# QTY Type 1 QTY Type 2 QTY Type 3 QTY Type 4 4 2 4 2 91103 BUMPER-SELF ADHESIVE 91105 RT SIDE OF LT MLD T4 1 91106 SLIDE T4 1 91107 DOOR-COLLECTION T4 1 91108 DOOR-COMPARTMENT T4 91110 MLD ASSY.-LT T2 91111 DOOR-COMPARTMENT 91112 PANEL-INSERT T2 91113 PANEL INSERT LT T4 91114 INSERT PANEL RT T4 91118 DOOR ASSY.-COLLECTION 13 1 8 12 16 1 1 1 1 1 1 91119 DOOR ASSY-COLLECTION T4 91120 HOUSING ASSY-SLIDE T1 & T2 1 1 91123 SCREW-TORX 8-32 X .
Part# Description QTY Type 1 QTY Type 2 QTY Type 3 QTY Type 4 91260 INSERT-THREADED 2 2 2 2 91262 BRACKET-STFNR TP & BTM. 1 1 1 1 91467 1 2 1 ROD-THREADED 1 91511-T1 NAMEPLATE KIT T1 1 91511-T2 NAMEPLATE KIT T2 91511-T3 NAMEPLATE KIT T3 91511-T4 NAMEPLATE KIT T4 91601 WASHER-BEARING 2 91602 DOOR/INSERT ASSY. T1 1 91604 DOOR/INSERT ASSY. T2 91610 LOCK ASSY.-PARCEL 91615 DOOR/INSERT ASSY. T3 91620 1 1 1 1 2 1 2 1 1 2 1 NUT-HEX .
